VAT 264 Series Installation, Operating, & Maintenance Instructions
Hv angle valve with manual actuator
Hide thumbs
Also See for 264 Series:
Table of Contents
Advertisement
HV Angle valve
● with manual actuator
This manual is valid for the valve ordering number(s):
26436-QA/H/E01
26436-GE01
The fabrication number is indicated on each product as per the label
below (or similar):
made in Switzerland
Fabrication No.:
patented
26. . . – . . . . – . . . . / . . . .
A – . . . . . .
Explanation of symbols:
Read declaration carefully before you start any other
action!
Attention!
Product is in conformity with EC guidelines,
if applicable!
Disconnect electrical power and compressed air
lines. Do not touch parts under voltage!
Read these «Installation, Operating & Maintenance Instructions» and the enclosed «General
Safety Instructions» carefully before you start any other action!
Imprint:
VAT Vakuumventile AG, CH-9469 Haag, Switzerland
Tel +41 81 771 61 61 Fax +41 81 771 48 30 CH@vatvalve.com www.vatvalve.com
Installation, Operating & Maintenance Instructions
Series 264, DN 63 (I.D.2
(Series 264)
. .
Fabrication number
1
/
")
2
Keep body parts and objects away from the valve
opening!
Hot surfaces; do not touch!
Loaded springs and/or air cushions are potential
hazards!
Wear gloves!
287199EA
2010-12-23
1/9
Advertisement
Table of Contents
Related Manuals for VAT 264 Series
Summary of Contents for VAT 264 Series
- Page 1 Read these «Installation, Operating & Maintenance Instructions» and the enclosed «General Safety Instructions» carefully before you start any other action! Imprint: VAT Vakuumventile AG, CH-9469 Haag, Switzerland 287199EA Tel +41 81 771 61 61 Fax +41 81 771 48 30 CH@vatvalve.com www.vatvalve.com...
- Page 2 VAT products. The VAT firmware contains a limited, time unlimited user license. The VAT firmware may not be used for purposes other than those intended nor is it permitted to make copies of the VAT firmware. In particular, it is strictly forbidden to give copies of the VAT firmware to other people.
-
Page 3: Table Of Contents
4.1.3 Installation of "actuator/gate assembly" ....................7 5 Drawing..................................8 6 Spare parts ................................9 7 Warranty ................................... 9 VAT Vakuumventile AG, CH-9469 Haag, Switzerland 287199EA Tel +41 81 771 61 61 Fax +41 81 771 48 30 CH@vatvalve.com www.vatvalve.com 2010-12-23... -
Page 4: Use Of Product
") Use of product Use product for clean and dry indoor vacuum applications under the conditions indicated in chapter «Technical data» only! Other applications are only allowed with the written permission of VAT. Technical data for standard valve Leak rate... -
Page 5: Installation Into The System
» lbf . ft inch A combination of both forces «F » and «M» is prohibited. Please contact VAT. Operation Normal operation The valve is fully open when the green marking on the spindle is visible. Operation under increased temperature See «1.1 Technical data»... -
Page 6: Maintenance & Repairs
Contamination from the process may influence the function and requires more frequent maintenance. Before carrying out any maintenance or repairs, please contact VAT. It has to be individually decided whether the maintenance/repair can be performed by the customer or has to be carried out by VAT. The fabrication number on the valve made in Switzerland Fabrication No.:... -
Page 7: Replacement Of Plate Seal
• Tighten 4 screws (60) uniformly and crosswise in 2 to 3 steps • Perform function and leak test VAT Vakuumventile AG, CH-9469 Haag, Switzerland 287199EA Tel +41 81 771 61 61 Fax +41 81 771 48 30 CH@vatvalve.com www.vatvalve.com... -
Page 8: Drawing
Series 264, DN 63 (I.D.2 ") Drawing (Drawing shows the angle valve version. Inline version has a different body.) VAT Vakuumventile AG, CH-9469 Haag, Switzerland 287199EA Tel +41 81 771 61 61 Fax +41 81 771 48 30 CH@vatvalve.com www.vatvalve.com 2010-12-23... -
Page 9: Spare Parts
(including any delay in or failure to deliver), packaging, storage or use of any product sold or delivered by VAT shall fail to conform to the...
Need help?
Do you have a question about the 264 Series and is the answer not in the manual?
Questions and answers