Table of Contents
Advertisement
Quick Links
Fast closing valve
with pneumatic actuator
This manual is valid for the valve ordering number(s):
77136- . E44- . . . .
77140- . E44- . . . .
77144- . E44- . . . .
The fabrication number is indicated on each product as per the label
below (or similar):
made in Sw itz er land
F abric ation N o.:
patented
771 . . – . . . . – . . . . / . . . .
A – . . . . . .
Explanation of symbols:
Read declaration carefully before you start any other
action!
Attention!
Product is in conformity with EC guidelines,
if applicable!
Disconnect electrical power and compressed air
lines. Do not touch parts under voltage!
Read these «Installation, Operating & Maintenance Instructions» and the enclosed «General
Safety Instructions» carefully before you start any other action!
VAT Vakuumventile AG, CH-9469 Haag, Switzerland
Tel +41 81 771 61 61 Fax +41 81 771 48 30 CH@vatvalve.com
Installation, Operating & Maintenance Instructions
Series 77.1, DN 63-160 CF-F (I.D. 2½"- 6")
. .
Fabr ication num ber
Keep body parts and objects away from the valve
opening!
Hot surfaces; do not touch!
Loaded springs and/or air cushions are potential
hazards!
Wear gloves!
www.vatvalve.com
283762EA
1/11
2010-04-21
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for VAT 77.1 Series
Summary of Contents for VAT 77.1 Series
- Page 1 Do not touch parts under voltage! Read these «Installation, Operating & Maintenance Instructions» and the enclosed «General Safety Instructions» carefully before you start any other action! VAT Vakuumventile AG, CH-9469 Haag, Switzerland 283762EA 1/11 Tel +41 81 771 61 61 Fax +41 81 771 48 30 CH@vatvalve.com www.vatvalve.com...
- Page 2 VAT products. The VAT firmware contains a limited, time unlimited user license. The VAT firmware may not be used for purposes other than those intended nor is it permitted to make copies of the VAT firmware. In particular, it is strictly forbidden to give copies of the VAT firmware to other people.
-
Page 3: Table Of Contents
4 Trouble shooting ............................... 9 5 Maintenance & repairs .............................. 9 6 Drawing................................... 10 7 Warranty ................................. 11 VAT Vakuumventile AG, CH-9469 Haag, Switzerland 283762EA 3/11 Tel +41 81 771 61 61 Fax +41 81 771 48 30 CH@vatvalve.com www.vatvalve.com... -
Page 4: Use Of Product
Series 77.1, DN 63-160 CF-F (I.D. 2½“- 6") Use of product Use product for clean and dry indoor vacuum applications under the conditions indicated in chapter «Technical data» only! Other applications are only allowed with the written permission of VAT. Technical data Leak rate <... -
Page 5: Installation
Installation into the system The valve must not support other components and has to be protected from forces of the system (e.g. by bellows sections). VAT Vakuumventile AG, CH-9469 Haag, Switzerland 283762EA 5/11 Tel +41 81 771 61 61 Fax +41 81 771 48 30 CH@vatvalve.com www.vatvalve.com... -
Page 6: Connections
To avoid malfunctions of the solenoid, we recommend to seal the thread of the compressed air inlet with liquid plastic (e.g. Loctite) and not by means of Teflon ribbon or similar fibrous material. VAT Vakuumventile AG, CH-9469 Haag, Switzerland 283762EA 6/11 Tel +41 81 771 61 61 Fax +41 81 771 48 30 CH@vatvalve.com... -
Page 7: Electrical Connection
Electrical connection between fast closing valve and controller is performed with a 12 pole plug and a single connection cabel according to the following drawing. Wiring diagram 12 pole plug VAT Vakuumventile AG, CH-9469 Haag, Switzerland 283762EA 7/11 Tel +41 81 771 61 61 Fax +41 81 771 48 30 CH@vatvalve.com www.vatvalve.com... -
Page 8: Operation
We recommend to use an emergency air reservoir at the compressed air input. Behavior in case of power failure The behaviour at power failure can be set inside the controller, either for «no change» or «valve closes». VAT Vakuumventile AG, CH-9469 Haag, Switzerland 283762EA 8/11 Tel +41 81 771 61 61 Fax +41 81 771 48 30 CH@vatvalve.com... -
Page 9: Trouble Shooting
Contamination from the process may influence the function and requires more frequent maintenance. Before carrying out any maintenance or repairs, please contact VAT. It has to be individually decided whether the maintenance/repair can be performed by the customer or has to be carried out by VAT. The fabrication number on the valve made in Switzerland Fabrication No.:... -
Page 10: Drawing
Installation, Operating & Maintenance Instructions Series 77.1, DN 63-160 CF-F (I.D. 2½“- 6") Drawing VAT Vakuumventile AG, CH-9469 Haag, Switzerland 283762EA 10/11 Tel +41 81 771 61 61 Fax +41 81 771 48 30 CH@vatvalve.com www.vatvalve.com 2010-04-21... -
Page 11: Warranty
(including any delay in or failure to deliver), packaging, storage or use of any product sold or delivered by VAT shall fail to conform to the...
Need help?
Do you have a question about the 77.1 Series and is the answer not in the manual?
Questions and answers