decorflame M405-48FBK Manual

decorflame M405-48FBK Manual

Electric fireplace heater
Table of Contents

Advertisement

Available languages

Available languages

Quick Links

iMpOrtaNt:
NOtE: DO NOt rEtUrN UNit tO tHE StOrE
BEFOrE cONtactiNG OUr cUStOMEr SErVicE
DEpartMENt. DO NOt DiSpOSE OF yOUr
cartONS UNtil yOU arE cOMplEtEly SatiSFiED
witH yOUr NEw FirEplacE HEatEr.
plEaSE NOtE: wHEN yOU OpEN tHE cartON carEFUlly cHEck
tHE UNit aND MakE SUrE tHErE iS NO DaMaGE. iF yOU HaVE
aNy prOBlEMS witH aSSEMBliNG tHE UNit, witH HOw tHE
VariOUS FUNctiONS wOrk Or witH DaMaGE Or MiSSiNG partS,
plEaSE GO tO OUr wEBSitE www.qUalitycraFt.cOM aND
click ON cUStOMEr SUppOrt.
NOtE: light bulbs may become loose during shipping. if the flame effect is dim or does not
work, please check that light bulb or bulbs are finger tight in socket. See instructions for
replacing bulb or bulbs.
NOtE: the electric fireplace heater may emit a slight harmless odor when first turned on. this
is caused by activating the internal heater components for the first time and should not occur
again.
INSTRUCTION MANUAL
attENtiON:
1. Find a location for the fireplace heater that is protected from direct sunlight.
2. Do not plug the unit into the power outlet before reading all instructions.
IMPORTANT SAFETY
INSTRUCTIONS
wHEN USiNG ElEctrical appliaNcES, BaSic prEcaUtiONS SHOUlD alwayS BE
FOllOwED tO rEDUcE tHE riSk OF FirE, ElEctric SHOck, aND iNJUry tO pErSONS,
iNclUDiNG tHE FOllOwiNG:
1) read all instructions before using this electric fireplace heater.
2) this electric fireplace heater is hot when in use. to avoid burns, do not let bare skin touch
hot surfaces. the grill directly in front of the heater outlet becomes hot during heater
operation. keep combustible materials, such as furniture, pillows, bedding, papers,
clothes, and curtains at least 3 ft (0.9 m) away from the front of the unit and keep them
away from the sides and rear.
3) Extreme caution is necessary when any heater is used by or near children or individuals
with disabilities and whenever the fireplace is left operating and unattended.
4) always unplug fireplace when not in use.
5) Do not operate any electric fireplace with a damaged cord or plug or after the heater
malfunctions, has been dropped or damaged in any manner.
ElEctric FirEplacE HEatEr
Model: M405-48FBK
6) Do not use outdoors.
7) this electric fireplace heater is not intended for use in bathrooms, laundry areas and
similar indoor locations. Never locate heater where it may fall into a bathtub or other
water container.
8) Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar
coverings. arrange cord away from traffic area and where it will not be tripped over.
9) to disconnect fireplace, turn controls to off, then remove plug from outlet.
10) connect to properly grounded outlets only.
11) Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this
may cause an electric shock or fire, or damage the heater.
12) to prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on
soft surfaces, like a bed, where openings may become blocked.
13) a heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline,
paint, or flammable liquids are used or stored.
14) Use this fireplace heater only as described in this manual. any other use not
recommended by the manufacturer may cause fire, electric shock, or injury to persons.
15) avoid the use of an extension cord because the extension cord may overheat and cause
a risk of fire. However, if you have to use an extension cord, the cord shall be No.14 awG
minimum size and rated not less than 1875 watts.
16) caution: Do not plug this product into a receptacle controlled by a wall switch or dimmer.
17) when storing or transporting the unit and cord, keep in a dry place, free from excessive
vibration and store so as to avoid damage.
SAVE THESE INSTRUCTIONS
FOR FUTURE USE.
caUtiON:
iF yOU USE tHiS HEatEr iN cONJUNctiON witH a tHErMal cONtrOl, a prOGraM
cONtrOllEr, a tiMEr Or aNy OtHEr DEVicE tHat SwitcHES tHE HEatEr ON
aUtOMatically, rEMEMBEr tO OBSErVE all SaFEty warNiNGS at all tiMES. tHE
FirEplacE HEatEr HaS SaFEty OVErHEat prOtEctiON. iF tHE OVErHEat prOtEctiON
tripS, SwitcH OFF all SwitcH BUttONS aND wait apprOxiMatEly 5 - 10 MiNUtES. it
SHOUlD rESEt aUtOMatically ONcE tHE UNit cOOlS DOwN.
warNiNG - DO NOt lOaD MOrE tHaN 22.7 kG (50 lBS) ON tHE tOp SHElF.
warNiNG: prOcEDUrES aND tEcHNiqUES iF NOt carEFUlly FOllOwED will rESUlt iN
DaMaGE tO tHE EqUipMENt aND will ExpOSE tHE USEr tO tHE riSk OF SEriOUS iNJUry,
illNESS Or DEatH.
A 15 AMP circuit is required to operate this heater. If the breaker trips when the heater
is used, then you may need to move the heater to another location or unplug other
appliances that are on the same circuit. If you require an extension cord use one that is
rated at 1875 watts.
1

Advertisement

Table of Contents
loading

Summary of Contents for decorflame M405-48FBK

  • Page 1 ElEctric FirEplacE HEatEr Model: M405-48FBK iMpOrtaNt: 6) Do not use outdoors. 7) this electric fireplace heater is not intended for use in bathrooms, laundry areas and NOtE: DO NOt rEtUrN UNit tO tHE StOrE similar indoor locations. Never locate heater where it may fall into a bathtub or other BEFOrE cONtactiNG OUr cUStOMEr SErVicE water container.
  • Page 2: Parts List

    This electric fireplace heater is for use on 120 volts. The cord has a plug,as shown at A in illustration below. An adapter, as shown at C, is available for connecting three-blade grounding-type plugs to two-slot receptacles. The green grounding plug extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box.
  • Page 3 Step 2: Attach 8 shelf supporting pins [O] to panels G, H, I and J, as shown in Fig. B. Step 6: Attach panel K in between panel G and I. Attach panel L in between panel J and H. See Fig.
  • Page 4 Step 9: Attach panel A to panel G and H with 4 long screws [W], as shown in Fig. I. Step 12: Attach door hinges [Q] to left door [M] and right door [N] with 8 mounting screws [T] (2 screws for each door hinge). Attach door handles [Pb] to left and right door [M and N] with door handle screws [Pa].
  • Page 5: Operation

    OPERATION Step 16: Make sure that the foam tape is completely covering both of the side flanges, as shown in Fig. O. After reading complete instructions, confirm all controls on fireplace are in the OFF position. Plug the fireplace into a 15 AMP/120 Volt outlet. If the cord does not reach, you may use an extension cord rated for a minimum of 1875 WATTS.
  • Page 6: Replacing The Light Bulbs

    REPLACING THE LIGHT BULBS REPAIRS Step 1: Remove 12 screws on the back of fireplace and open the rear cover. There are 2 If any problems are found with the original parts during mantel assembly such as the larger screws and 10 smaller screws. panels cannot be installed with the plastic connector.
  • Page 7: Warranty

    WARRANTY OptiON 2: Use the small L-brackets and screws. Every electric fireplace heater is tested before it leaves the factory and it is guaranteed for one year. If the unit should fail to operate correctly within one year from the date of 1.
  • Page 8 FOyEr ÉlEctriqUE Modèle : M405-48FBK iMpOrtaNt : 3) Faites preuve de la plus grande prudence lorsqu’un poêle est utilisé à proximité d’enfants ou de personnes invalides, ou par ceux-ci, et chaque fois que l’appareil est laissé en état rEMarqUE : NE paS rEtOUrNEr l’UNitÉ aU de marche, sans surveillance.
  • Page 9: Liste Des Pièces

    lES aVErtiSSEMENtS rElatiFS À la SÉcUritÉ, EN tOUt tEMpS. cE FOyEr cOMpOrtE Q) Charnières de porte ....................4 UNE prOtEctiON iNcOrpOrÉE cONtrE lES SUrcHaUFFES. Si la prOtEctiON cONtrE R) Guide-câble ......................1 la SUrcHaUFFE SE DÉclENcHE, ÉtEiGNEz tOUS lES iNtErrUptEUrS Et attENDEz S) Équerres de montage ...................
  • Page 10 ASSEMBLAGE DU MANTEAU : Étape 4 : Fixer les panneaux G, H, I et J au panneau D avec huit vis longues [W]. Voir la figure D. aVErtiSSEMENt : Placer un morceau de carton ou une couverture de protection sur le plancher afin d’éviter d’égratigner la surface du manteau de foyer pendant l’assemblage.
  • Page 11 Étape 7 : Fixer le panneau C aux panneaux G, H, I et J avec les huit vis longues [W] comme Étape 9 : Fixer le panneau A aux panneaux G et H avec quatre vis longues [W] comme illustré dans la figure G. illustré...
  • Page 12 Étape 12 : Poser les charnières [Q] de la porte gauche [M] et de la porte droite [N] Étape 16: S’assurer que le ruban mousse recouvre complètement les deux rebords avec huit vis de montage [T] (deux vis pour chaque charnière). Installer les comme illustré...
  • Page 13: Remplacer Les Ampoules

    FONCTIONNEMENT REMPLACER LES AMPOULES Suite à la lecture complète des directives, vérifier si toutes les commandes sont Étape 1 : Enlever les 12 vis à l’arrière du foyer et retirer le panneau arrière du foyer. éteintes (OFF). Brancher le foyer dans une prise de courant de 15AMP/120Volt. Si le Il y a 2 grandes vis et 10 vis plus courtes.
  • Page 14: Pièces De Remplacement

    RÉPARATIONS OptiON 2 : Utiliser les petites équerres et les vis Si des problèmes surviennent avec les pièces d’origines pendant l’assemblage du manteau de foyer, tels que problèmes d’installation des panneaux avec les raccords 1. Placer une petite équerre sur le meuble, tel qu’illustré et faire une marque pour définir de plastique.
  • Page 15: Garantie

    GARANTIE Chaque foyer électrique est testé avant de quitter l’usine et est garanti pendant un an. Si l’appareil ne fonctionne pas correctement dans la période d’un an à compter de la date d’achat, allez sur notre site Web www.qualitycraft.com et cliquez sur Soutien à...
  • Page 16: Instrucciones Importantes De Seguridad

    ElÉctricO Modelo: M405-48FBK iMpOrtaNtE: 5) No haga funcionar ninguna chimenea que tenga un cordón o enchufe dañado o después de que haya funcionado mal, se haya caído o dañado. NOta: NO DEVUElVa la UNiDaD a la tiENDa 6) No utilice la chimenea al aire libre.
  • Page 17: Lista De Piezas

    aDVErtENcia: Y) JUEGO PARA AUTORREPARACIONES Pintura para efectuar retoques (botella) .............. 1 Si no se siguen atentamente los procedi-mientos y técnicas indicados, se dañará el Soporte en forma de “L” ..................2 equipo; el usuario quedará expuesto al riesgo de sufrir lesiones o dolencias graves o Tornillos para el soporte en forma de “L”...
  • Page 18 Paso 1: Sujete los 36 conectores plásticos [X] a los paneles G, H, I. J, Da, Dd, Dc, y Dd con Paso 4: Sujete los paneles G, H, I y J al panel D con 8 tornillos largos [W]. Vea la fig. D. 72 tornillos largos [W] (2 tornillos para cada conector).
  • Page 19 Paso 7: Sujete el panel C a los paneles G, H, I y J con 8 tornillos largos [W], como se Paso 9: Sujete el panel A a los paneles G y H con 4 tornillos largos [W], como se muestra muestra en la fig.
  • Page 20 Paso 12: Sujete las bisagras de la puerta [Q] a la puerta izquierda [M] y a la puerta Paso 16: Procure que la cinta de espuma cubra completamente ambos rebordes laterales, derecha [N] con 8 tornillos de montaje [T] (2 tornillos para cada bisagra). Sujete como se muestra en la fig.
  • Page 21: Operación

    OPERACIÓN REEMPLAZO DE LAS BOMBILLAS Paso 1: Quite 12 tornillos de la parte trasera de la chimenea y abra la cubierta trasera. Después de leer las instrucciones completas, compruebe que todos los controles Verá 2 tornillos grandes y 10 pequeños. de la chimenea estén en la posición de apagado (OFF).
  • Page 22: Piezas De Repuesto

    REPARACIONESS OpcióN 2: Utilice los soportes largos pegueños y los tornillos argos. En el caso de que surjan problemas con las piezas originales durante el montaje de la repisa, por ejemplo, que los paneles no puedan instalarse con el conector plástico, 1.
  • Page 23 GARANTÍA Todos los calefactores eléctricos de chimenea se prueban antes de salir de la fábrica y cuentan con una garantía de un año. Si la unidad no funciona correctamente dentro del año a partir de la fecha de compra, visite nuestro sitio web www.qualitycraft. com y haga clic en ayuda al cliente.

Table of Contents