Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for PERCo RTD-03S
Summary of Contents for PERCo RTD-03S
- Page 1 Waist high Rotor Turnstile RTD-03S OPERATION MANUAL...
- Page 2 Waist-high Rotor Turnstile RTD-03S Operation manual...
-
Page 3: Table Of Contents
Power-up ........................16 Operating modes ......................17 Operation from the built-in SPS .................. 19 Operation from the external power supply..............19 Troubleshooting ......................19 MAINTENANCE ........................20 TRANSPORTATION AND STORAGE ................. 20 Appendix. Guide barriers set versions for RTD-03S turnstile ............ 21... -
Page 4: Application
The operation manual for RTD-03S waist-high rotor turnstile contains data that is necessary for the most full usage of operating advantages of the turnstile as well as chapters on packaging, installation and maintenance. -
Page 5: Delivery Set
Operation manual 4 DELIVERY SET 4.1 Standard delivery set Basic equipment: Turnstile post assembled ......................1 Barrier wing with fastenings ......................4 Filler panel ..........................4 Control unit CU-05.2 with 1.5 m power cable................1 Remote control panel with cable 6.6 m long ................ -
Page 6: Design
The remote control panel (9) is connected to the processor module inside the control unit (8) with a multi-thread floppy tape (13) via a cable inlet on the lower panel of the control unit (Fig. 3 and Fig. 9). Figure 1. Dimensions of the RTD-03S waist-high rotor turnstile... - Page 7 Operation manual Figure 2. RTD-03S waist-high rotor turnstile overall view 1 – rotary post; 2 – post with flange; 3 – cover; 4 – mechanical release lock; 5 – mechanical release key; 6 – barrier wing; 7 – filler panel; 8 – control unit;...
- Page 8 RTD-03S Waist-high rotor turnstile Figure 3. Control unit...
-
Page 9: Control Over The Turnstile
Operation manual The control unit (CU) (8) (see Fig. 2, 3) is intended for the turnstile units powering and control. It comes as a standalone unit in a metal case with the pull-resistant fasteners for wall mounting. The CU can also be desk-mounted. The CU case contains the power transformer, the DC power supplies module, the processor module and two 12V SPS batteries. - Page 10 RTD-03S Waist-high rotor turnstile Pin number Signal RIGHT STOP LEFT Pwr Failure E PASS L1 PASS R1 Pwr Failure C PASS L2 PASS R2 Pass Sensor 1 Bat Failure C Bat Failure E Pass Sensor 2 Pin number Signal +24V Figure 4.
- Page 11 Operation manual At the AC mains failure the transistor is closed; • «Bat failure C» – built-in SPS failure (contacts “Pwr failure C” and “Pwr failure E” – collector (+) and emitter (-) of the galvanic decoupling circuit correspondingly). At the built-in SPS failure (the battery discharge up to 22.5V) the transistor is closed; •...
-
Page 12: General Requirements For Indicators Connection To The Turnstile
RTD-03S Waist-high rotor turnstile 5.4 General requirements for indicators connection to the turnstile For indication control is used a transistor circuit with open collector (see Fig. 6). Figure 6. Indication control circuit The connector (the RC7TV plug) pins assignment for indicators connection on the cable connectors block: ... -
Page 13: Marking And Packaging
Operation manual 6 MARKING AND PACKAGING The turnstile has the following marking: • on the turnstile post – a label located on the underside of the flange; on the control unit – a label located on the rear panel of the control unit. •... -
Page 14: Installation Procedure
(10) and the power cable (11) as shown in Fig. 7 and according to your checkpoint layout. Figure 7. Marking layout for RTD-03S installation (dotted line shows the dimensions of the turnstile and the position of one of its wings) Drill the holes for the cables and PFG IH 10 anchor bolts for the turnstile post mounting (3 holes Ø16×60mm) in the floor. - Page 15 Operation manual connectors block (16) into the turnstile post with flange (2) at height suitable for further installation. Place the turnstile post in the upright position. Mount the turnstile post flange on the anchor bolts sleeves. The turnstile post should be mounted strictly upright.
-
Page 16: Electrical Connection Layout
RTD-03S Waist-high rotor turnstile 10. Connect the cables 10, 11, 13 to the control unit (8) as follows (see Fig. 3): control cable (10) to the “Control” connector; • power cable (11) to the “DC=24V” connector; • put remote control cable (13) through its cable inlet inside the control unit and connect it •... -
Page 17: Operation Instructions
Operation manual Table 1. List of elements of the turnstile connection layout Legend Item Qty. Comments Turnstile post Control unit Processor module Remote control panel Wireless remote control ∗ ACS controller ∗ External power supply 24VDC ∗ Intrusion detector ∗ Siren ∗... -
Page 18: Operating Modes
RTD-03S Waist-high rotor turnstile 9.2 Operating modes After its power-up the reset state of the turnstile is the “Closed” position (the mechanical lock is locked up with a key). The following operating modes with the corresponding indication, which can be set from the RC, are shown in Table 1. - Page 19 Operation manual • Set the «Power» and «Battery» switchers on the control unit (8) in the «0» position (Fig. 3); • Disconnect the power cable (12) from the mains; • Swap positions of the following RC cables inside the control unit, on the connectors X3 and X4 of the processor module (Fig.
-
Page 20: Operation From The Built-In Sps
RTD-03S Waist-high rotor turnstile Indication Turnstile operating Indication on № Your actions outputs Turnstile status mode the RC status “LED Grn_L” Always free (open for Press all the three The two green The barrier wings buttons on the RC indicators (left... -
Page 21: Maintenance
Operation manual Table 3. Potential problems and their remedies № Fault Possible cause Remedy The turnstile does not work after its power- The "220V/1A" fuse is Turn the “Power” toggle up (the “Power” toggle switch is in the “I” burnt out switch to the “O”... -
Page 22: Appendix. Guide Barriers Set Versions For Rtd-03S Turnstile
RTD-03S Waist-high rotor turnstile Appendix. Guide barriers set versions for RTD-03S turnstile RB-03TP guide barriers set Guide barriers set posts — polished tubular stainless steel dia 50 mm; rails — beechwood (ashwood); filler panels — tinted polycarbonate plastic; mnemonic indication units. - Page 23 Operation manual RB-03SP guide barriers set Guide barriers set posts – polished tubular stainless steel dia 50 mm; rails – polished tubular stainless steel dia 32 mm; filler panels – tinted polycarbonate plastic; symbol indication units. RB-03T guide barriers set Guide barriers set posts —...
- Page 24 RTD-03S Waist-high rotor turnstile Marking layout for installation of turnstile with guide barriers set: (electric raceway to the control unit is laid from the turnstile post center in the direction of the control unit according to the layout). Figure 11. Marking for mounting of the railing set posts...
- Page 25 PERCo Polytechnicheskaya str., 4, block 2 194021, Saint Petersburg Russia Tel: +7 812 247 04 64 E-mail: export@perco.com support@perco.com www.perco.com...
- Page 26 www.perco.com...
Need help?
Do you have a question about the RTD-03S and is the answer not in the manual?
Questions and answers