ADJ FOCUS BEAM LED User Instructions
Hide thumbs Also See for FOCUS BEAM LED:

Advertisement

Quick Links

FOCUS BEAM LED
User Instructions

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FOCUS BEAM LED and is the answer not in the manual?

Questions and answers

Summary of Contents for ADJ FOCUS BEAM LED

  • Page 1 FOCUS BEAM LED User Instructions...
  • Page 2 ©2021 ADJ Products, LLC all rights reserved. Information, specifications, diagrams, images, and instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted.
  • Page 3: Table Of Contents

    CONTENTS General Information Limited Warranty (USA Only) Safety Guidelines Maintenance Guidelines Overview Static Gobos Fixture Installation DMX Setup DMX Addressing System Menu DMX Traits: Channel Functions & Values Dimmer Curve Chart Fuse Replacement / Cleaning / Troubleshooting Specifications...
  • Page 4: General Information

    GENERAL INFORMATION INTRODUCTION Please read and understand all instructions in this manual carefully and thoroughly before attempting to operate these products. These instructions contain important safety and use information. UNPACKING The products in this kit have been thoroughly tested and have been shipped in perfect operating condition.
  • Page 5: Limited Warranty (Usa Only)

    All shipping charges must be pre-paid. If the requested repairs or service (including parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return shipping charges only to a designated point within the United States. If the entire instrument is sent, it must be shipped in its original package. No accessories should be shipped with the product.
  • Page 6: Safety Guidelines

    To guarantee a smooth operation, it is important to follow all instructions and guidelines in this manual. ADJ PRODUCTS LLC is not responsible for injury and/or damages resulting from the misuse of these devices due to the disregard of the information printed in this manual. Only qualified and/or certified personnel should perform installation of these devices and only the original rigging parts included with these devices should be used for installation.
  • Page 7 SAFETY GUIDELINES DO NOT position devices close to any FLAMMABLE MATERIALS while operating. DO NOT attempt installation and/or operation of devices without knowledge how to do so. DO NOT permit operation by persons who are not qualified to operate these types of devices. DO NOT shake devices, avoid brute force when installing and/or operating.
  • Page 8 LEDs. This issue is not specific only to ADJ lighting fixtures, it is a common issue with lighting fixtures from all manufacturers. Although there is no true way to fully prevent this issue from happening, the guidelines below can prevent any potential damage from occurring if followed.
  • Page 9: Maintenance Guidelines

    Regular inspections are recommended to insure proper function and extended life. There are no user serviceable parts inside this fixture, please refer all other service issues to an authorized ADJ service technician. Should you need any spare parts, please order genuine parts from your local ADJ dealer.
  • Page 10: Overview

    OVERVIEW UP Button RIGHT Button ENTER Button SERVICE PORT IP65 Locking DOWN Button IP65 Locking Power LEFT Button Power Connectors Out Menu Screen Connector In IP65 Locking 5-Pin DMX In/Out Safety Cable Attachment Point Carrying Handle Omega Bracket Attachment Point...
  • Page 11: Static Gobos

    STATIC GOBOS...
  • Page 12: Fixture Installation

    FIXTURE INSTALLATION OMEGA BRACKETS INSTALLATION Insert the Omega Brackets into the matching holes on the bottom of the fixture. Secure the Omega Brackets to the fixture by turning each quick-lock fastener ¼ turn clockwise; making sure the fastener is completely locked. 4x Omega Bracket Attachment Points Safety Cable (not included)
  • Page 13 CLAMP FAILS. AROUND CABLE CONNECTIONS. The Focus Beam LED is fully operational in three different mounting positions, hanging upside-down, mounted sideways on trussing, or set on a flat level surface. Always use and install a safety cable as a safety measure to prevent accidental damage and/or injury in the event the clamp fails. Never use the...
  • Page 14: Dmx Setup

    DATA CABLE (DMX CABLE) REQUIREMENTS (FOR DMX AND PRIMARY/SECONDARY OPERATION): The Focus Beam LED can be controlled via DMX-512 protocol. Your unit and your DMX controller requires a 5-pin XLR connector for data input and data output. We recommend Accu-Cable DMX cables.
  • Page 15 3 of a male XLR connector (DATA + and DATA -). This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable terminator (ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior.
  • Page 16: Dmx Addressing

    DMX ADDRESSING All fixtures should be given a DMX starting address when using a DMX controller, so the correct fixture responds to the correct control signal. This digital starting address is the channel number from which the fixture starts to “listen” to the digital control signal sent out from the DMX controller. The assignment of this starting DMX address is achieved by setting the correct DMX address on the digital control display on the fixture.
  • Page 17: System Menu

    SYSTEM MENU The fixture includes an easy to navigate system menu control panel display where all necessary settings and adjustments are made. (See image below) During normal operation, pressing the MODE button once will access the fixture’s main menu. Once in the main menu, you can navigate through the different menus and the sub-menus with the UP and DOWN buttons.
  • Page 18 SYSTEM MENU (Software Version >V1.0.3) OPTIONS / VALUES MENU SUBMENU DESCRIPTION (Default Settings in BOLD) Set Address 001-XXX DMX Addressing DMX SETTINGS DMX Channel Mode 16Ch / 18Ch DMX Channel Mode Selection Hold Last / Blackout / Manual No DMX Status DMX Lost Status Pan Invert: ON / OFF Reverse Pan Motion...
  • Page 19 SYSTEM MENU (Software Version >V1.0.4) OPTIONS / VALUES MENU SUBMENU DESCRIPTION (Default Settings in BOLD) Set Address 001-XXX DMX Addressing DMX SETTINGS DMX Channel Mode 16Ch / 18Ch DMX Channel Mode Selection Hold Last / Blackout / Manual No DMX Status DMX Lost Status Pan Degree: 630 / 540 Pan Degree Selection...
  • Page 20 SYSTEM MENU MENU SUBMENU OPTIONS / VALUES DESCRIPTION (Default Settings in BOLD) Program 1 Speed: 000~255 Fade: 000~255 Program 1 with Adjustments Program 2 Speed: 000~255 Fade: 000~255 Program 2 with Adjustments Program 3 Speed: 000~255 Fade: 000~255 Program 3 with Adjustments INTERNAL Program 4 Speed: 000~255 Fade: 000~255...
  • Page 21 SYSTEM MENU DMX SETTINGS - The submenus listed under DMX SETTINGS are as follows: Set Address, DMX Channel Mode, and No DMX Status. • SET ADDRESS - In this submenu you can find and set your desired DMX address. • DMX CHANNEL MODE - In this submenu you can find and set your desired DMX channel mode. •...
  • Page 22 SYSTEM MENU INTERNAL PROGRAMS - In this menu you are able to select 1 of 7 internal programs to run. Program running speed and fade speed are adjustable. INFORMATION - The submenus listed under INFORMATION are as follows: Fixture Life Time, Total LED Time, Fixture Temps, Fan Info.
  • Page 23 SYSTEM MENU Primary-Secondary Configuration: This function will allows you to link units together to run in a Primary-Secondary set-up. In a Primary-Secondary set up one unit will act as the controlling unit and the others will react to the controlling units built-in programs.
  • Page 24: Dmx Traits: Channel Functions & Values

    DMX TRAITS: CHANNEL FUNCTIONS & VALUES (16/18 DMX Channels) 16 Channels 18 Channels Values Functions PAN MOVEMENT 8-BIT: 000-255 Pan Movement (0° - 630°) PAN FINE 16-BIT: 000-255 Fine Control of Pan Movement TILT MOVEMENT 8-BIT: 000-255 Tilt Movement (0° - 270°) TILT FINE 16-BIT: 000-255 Fine Control of Tilt Movement...
  • Page 25 16 Channels 18 Channels Values Functions GOBO WHEEL: 000-003 Open 004-007 Gobo 1 008-011 Gobo 2 012-015 Gobo 3 016-019 Gobo 4 020-023 Gobo 5 024-027 Gobo 6 028-031 Gobo 7 032-035 Gobo 8 036-039 Gobo 9 040-043 Gobo 10 044-047 Gobo 11 048-051...
  • Page 26 16 Channels 18 Channels Values Functions SHUTTER & STROBING: 000-031 Close 032-063 Open 064-095 Strobing Slow - Fast 096-127 Open 128-159 Pulsating Strobe 160-191 Open 192-223 Random Strobing Slow - Fast 224-255 Open MASTER DIMMER: 000-255 0% - 100% DIMMER FINE: 000-255 0% - 100% FOCUS:...
  • Page 27 16 Channels 18 Channels Values Functions LED REFRESH RATE & SPECIAL FUNCTIONS: 000-010 Default LED Refresh Rate 1200Hz 011-078 Refresh Rate (Hz) 1000 1010 1020 1030 1040 1050 1060 1070 1080 1090 1100 1110 1120 1130 1140 1150 1160 1170 1180 1190 1210...
  • Page 28 16 Channels 18 Channels Values Functions LED REFRESH RATE & SPECIAL FUNCTIONS: 1410 1420 1430 1440 1450 1460 1470 1480 1490 1500 2500 4000 5000 6000 10,000 15,000 20,000 25,000 Disable LED Refresh Rate 080-089 Enable Blackout with Pan/Tilt Movement 090-099 Disable Blackout with Pan/Tilt Movement 100-109...
  • Page 29: Dimmer Curve Chart

    DIMMER CURVE CHART...
  • Page 30: Fuse Replacement / Cleaning / Troubleshooting

    DIMMER CURVE CHART Fuse Replacement Unplug the unit from any power source it may be connected to. Once the power has been disconnected, use a flat head screw driver to unscrew the fuse holder located next to the powerCON input. Remove the bad fuse and replace with a new one, and screw the fuse holder back in.
  • Page 31: Specifications

    SPECIFICATIONS Light Source: • 1x 80W Cool White LED Engine • 2.5° Beam Angle • Color Temperature: 7400K • 50,000 Hour Average LED Life Features: • Control Protocol: DMX & RDM (Remote Device Management) • DMX Modes: 2 (16 & 18) •...
  • Page 32 DIMENSIONS (VERTICAL)
  • Page 33 FCC STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC RADIO FREQUENCY INTERFERENCE WARNINGS &...

Table of Contents