Page 2
Products, LLC brands and product names are trademarks or registered trademarks of their respective companies. ADJ Products, LLC and all affiliated companies hereby disclaim any and all liabilities for property, equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic...
TABLE OF CONTENTS General Information Key Features | Warranty Returns Limited Warranty (USA Only) Safety Guidelines Overview DMX Set Up Installation Gobo Replacement Control Panel System Menu DMX Addressing DMX Traits White Color Temperature Presets Color Wheel Dimmer Modes and Curves Frame Macros Table Cleaning and Maintenance Fuse Replacement | Software Updates...
GENERAL INFORMATION Introduction: Congratulations on your purchase of the ADJ Focus Profile! This device is a 400W, CMY (Cyan, Magenta, Yellow), LED moving head spot, and has been designed to perform reliably for years when the guidelines in this booklet are followed. Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this device.
KEY FEATURES • 400W LED engine • 20,000 total lumens (fully zoomed out) • 7 to 45 degree zoom range • 6,700K color temperature • >70 CRI • 4 rotating framing shutter blades • Full CMY color mixing • 0-100% variable CTO INCLUDED ITEMS: •...
LIMITED WARRANTY (USA ONLY) A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories.
SAFETY GUIDELINES For Your Own Personal Safety, Please Read and Understand This Manual Completely Before You Attempt To Install Or Operate This Unit! • Be sure to save the packing carton in the unlikely event the device may have to be returned for service.
DMX chain. Data Cable (DMX Cable) Requirements (For DMX Operation): The Focus Profile can be controlled via DMX-512 protocol. The DMX address is set on the front panel of the fixture. Your unit and your DMX controller require a standard 3-pin XLR connector for data input and data output.
Page 10
XLR connector of the last unit in your daisy chain to terminate the line. Using a cable terminator (ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior. 5-Pin XLR DMX Connectors. Some manufacturers use 5-pin DMX-512 data cables for DATA trans- mission in place of 3-pin.
INSTALLATION IP RATING This device is IP20 rated. It is protected against instrusion of solids larger than 12.5mm in size, or approximately the size of an adult finger. The device is NOT protected against liquid instrusion of any kind. FLAMMABLE MATERIAL WARNING! Keep device a minimum of 5.0 feet (1.5m) away from flammable material and/or pyrotechnics.
Page 12
LEDs. This issue is not unique to ADJ lighting fixtures; it is a common issue with lighting fixtures from all manufacturers. Although there is no true way to fully prevent this issue from happening, the guide- lines below can reduce the risk of any potential damage if followed.
Page 13
INSTALLATION CLAMP INSTALLATION This fixture features multiple mounting clamp attachment points, as well as a safety cable attach- ment point, located on the bottom face of the fixture (see the illustration below). When mounting the fixture to a truss or any other suspended or overhead installation, be sure to secure appropriately rated clamps (not included) to the clamp attachment points and attach a separate SAFETY CABLE of the appropriate safety rating to the safety cable rigging point.
Page 14
The Focus Profile is fully operational in three different mounting positions: hanging upside-down from a ceiling or trussing, sideways on trussing, or set on a flat level surface. Be sure this fixture is kept at least 12m (40ft) away from any flammable materials (decoration etc.).
GOBO REPLACEMENT 1. Engage both the pan and tilt locks. Use a screwdriver to loosen the 4 fasteners that secure the cover (left), then unclip the security cable (right) and remove the cover. Repeat this process for both halves of the cover. 2.
Page 16
GOBO REPLACEMENT 3. Locate the two screws that hold the gobo wheel module in place. The first screw is located below and left of the stepper motors, and the second is located below and right of the electrical con- nector that was disconnected in Step 2. 4.
Page 17
GOBO REPLACEMENT 5. Rotate the replaceable gobo wheel (top wheel) so that the gobo you wish to replace is positioned near the open area just behind the left-most stepper motor. Then rotate the non-replaceable gobo wheel (bottom wheel) so that the open slot is aligned with the gobo you wish to replace. The top image shows the 2 gobo wheels out of alignment;...
Page 18
GOBO REPLACEMENT 6. Firmly grasp the holder of the gobo you wish you replace by the toothed gear portion. Lift the gobo upward, gently pushing from below with a finger if necessary (left), then pull the holder out- ward (right) to remove from the gobo wheel. 7.
Page 19
GOBO REPLACEMENT 8. Place the new gobo in the gobo holder, and re-install the retainer spring. 9. Manually rotate the silver central gear of the gobo wheel so that the positioning mark is aligned with the slot where you will be installing the new gobo. 10.
CONTROL PANEL This fixture includes an easy to navigate control panel display, from which all necessary settings and adjustments can be made. During normal operation, pressing the MODE button once will access the fixture’s main menu. Once in the main menu, the UP and DOWN buttons can be used to navi- gate through the different functions.
SYSTEM MENU A001~AXXX Set Address Standard 40 DMX Channel Basic 36 Mode DMX SETTINGS Extended 51 Hold Last No DMX Status Blackout Manual On / Off Primary On / Off Secondary 630 / 540 Pan Degree On / Off Pan Invert Status Settings On / Off Tilt Invert...
Page 22
SYSTEM MENU 900Hz~1500Hz, 2500Hz, 4000Hz, Default = 15KHz LED Refresh Rate 5000Hz, 6000Hz, 10KHz, 15KHz, 20KHz, 25KHz Linear Square Dim Curve Inverse Square S-Curve Off / On CT Mode Yes / No Reset All Motors Yes / No Pan/Tilt Reset Yes / No Color Reset Yes / No...
Page 23
SYSTEM MENU Gobo2 000-255 Gobo2Rot 000-255 Shutter 000-255 Dimmer 000-255 Dimmer Fine 000-255 Prism 1 000-255 Prism 1 Rot 000-255 Prism 1 Rot Fine 000-255 Prism 2 000-255 MANUAL Prism 2 Rot 000-255 CONTROL (cont’d from prev Prism 2 Rot Fine 000-255 page) Focus...
Page 24
SYSTEM MENU Speed 000-255 INTERNAL Program 6 Fade 000-255 PROGRAMS (cont’d from prev Speed 000-255 Program 7 page) Fade 000-255 Power On Time xxxxxx Hours Fixture Life Time P-On Time-R xxxxxx Hours P-On Time-Reset Passcode = 050 LED On Time xxxxxx Hours Total LED Time LED ON Time-R...
DMX ADDRESSING All fixtures should be given a DMX starting address when operating with a DMX controller, in order to ensure that the correct fixture responds to the correct control signal. This digital starting address is the channel number from which the fixture starts to “listen” to the digital control signal sent out from the DMX controller.
DMX TRAITS CHANNEL VALUES FUNCTION 36-CH 40-CH 51-CH Pan Movement, 630/540 000 - 255 Pan Fine 000 - 255 Tilt Movement 000 - 255 Tilt Fine 000 - 255 Cyan 000 - 255 Cyan Fine 000 - 255 Magenta 000 - 255 Magenta Fine 000 - 255 Yellow...
Page 27
DMX TRAITS CHANNEL VALUES FUNCTION 36-CH 40-CH 51-CH Color Wheel (continued) Green 083 - 092 Green - Yellow Yellow 094 - 104 Yellow - CRI 106 - 116 CRI - CTB 118 - 126 CTB - Open Color off (open) 128 - 190 Clockwise color wheel rotation, fast to slow 191 - 192...
Page 28
DMX TRAITS CHANNEL VALUES FUNCTION 36-CH 40-CH 51-CH Rotating Gobos, continuous rotation (continued) 105 - 178 Clockwise gobo wheel rotation, fast to slow 179 - 181 Stop gobo wheel rotation 182 - 255 Counter-clockwise gobo wheel rotation, slow to fast Gobo Rotation 000 - 127 Gobo Rotation Indexing...
Page 29
DMX TRAITS CHANNEL VALUES FUNCTION 36-CH 40-CH 51-CH Shutter, Strobe 000 - 031 No function (shutter closed) 032 - 063 No action, shutter open 064 - 095 Strobe, slow to fast 096 - 127 No action, shutter open 128 - 159 Pulse effect, slow to fast 160 - 191 No action, shutter open...
Page 30
DMX TRAITS CHANNEL VALUES FUNCTION 36-CH 40-CH 51-CH Zoom, minimum to maximum beam angle 000 - 255 Zoom Fine 000 - 255 Iris 000 - 191 Diameter, maximum to minimum 192 - 223 Pulse opening, fast to slow 224 - 255 Pulse closing, slow to fast Iris Fine 000 - 255...
Regular inspections are recommended to insure proper function and extended life. There are no user serviceable parts inside this fixture. Please refer all other service issues to an authorized ADJ service technician. Should you need any spare parts, please order genuine parts from an authorized ADJ dealer.
DOWNLOAD FIXTURE SOFTWARE TO PC ONLY! (NO MAC SUPPORT) PLEASE CONTACT ADJ CUSTOMER SERVICE FOR FURTHER INFORMATION. 1. Contact ADJ customer service to obtain the updated software. Download software to a USB flash drive. In order to minimize the risk of downloading the incorrect software to your device, make sure that the desired update files are the only files on the USB flash drive.