SOMFY Sonesse 30 RTS Instructions Manual
  1. Manuals
  2. Brands
  3. SOMFY Manuals
  4. Engine
  5. sonesse 30 rts
  6. Instructions manual

SOMFY Sonesse 30 RTS Instructions Manual

Hide thumbs Also See for Sonesse 30 RTS:
Table of Contents

Advertisement

Quick Links

Download this manual
Somfy RTS Motor Programming Instructions
Motor Programming Instructions have been rewritten by
https://www.AVOutlet.com
We rewrite the Somfy instructions in an effort to make things a little easier to follow. There are
however some subtle differences in the motors. Please refer to the included Somfy motor
specific instructions if something is not working. Feel free to let us know if something is found to
be incorrect.
Please Read and Follow These Instructions.
Please use the motor programming instructions provided here. The remote control
instructions can be used for reference but they are not as easy to follow. A copy of the
Somfy instructions are also provided for your reference.
Please read installation instructions and programming instructions completely prior to
proceeding with installation and programming. Failure to do so can result in damage to the
motor and or the shade.
Be prepared to stop the shade during programming. The programming step where you set the
first stop limit (upper or lower whichever you do first) will activate the motor to move without
stopping on its own. You will need to stop the motor at the next stop limit using the remote as
indicated. Failure to stop the shade can result in shade or motor damage.
The motors MUST be installed in the tube and the assembly must be mounted into brackets to
be able to program the motor.
Only apply power to the motor being programmed regardless if the other motors have been
programmed or not. This will prevent inadvertent interaction with other motors. This is not
possible for motors with built-in batteries like the R28WF, ST30WF etc. Motors with built-in
batteries must be put to sleep.
We recommend mapping out the installation before proceeding. This will reduce set-up time and
make life easier. Decide the channels and or additional remotes to be assigned to each shade
in the installation. Each shade should be completely programmed before moving to the next.
Have the necessary remotes and controls ready prior to proceeding.
All motors programmed to the same RTS channel will operate at the same time. If you want
individual control of the motor, you must use separate channels on multi-channel remotes or
separate single channel remotes
The remote controls are generally considered to be dummy devices as they do not store any
motor or programming information. The motors are the intelligent devices. The motors store the
shade operation limits in their memory and the motors also memorize the specific remotes or
channels assigned to control them. Each motor can have up to 12 remotes or channels
controlling them.
th
Note: The Telis 4 Remote Control is a 5 Channel Remote control. The 5
channel is all lights
th
on. The 5
channel by default is not a group channel. This channel is not automatically
assigned and must be programmed.

Advertisement

Table of Contents
loading

Related Manuals for SOMFY Sonesse 30 RTS

Summary of Contents for SOMFY Sonesse 30 RTS

  • Page 1 Motor Programming Instructions have been rewritten by https://www.AVOutlet.com We rewrite the Somfy instructions in an effort to make things a little easier to follow. There are however some subtle differences in the motors. Please refer to the included Somfy motor specific instructions if something is not working.
  • Page 2 Please read the previous page before proceeding. Step 1 - Assign a RTS Channel to the Motor 1-A) Select the RTS remote control and channel you want to use. 1-B) Press and Hold both the UP and DOWN buttons simultaneously until the motor jogs, then release.
  • Page 3 Optional Programming Tasks These procedures can be done at any time after initial programming, but we do recommend performing all desired additional tasks before moving onto the next shade. All shades not being programmed should have the power disconnected be put to sleep. Set the Customer Preferred MY Intermediate Position 1) Using the remote, position the shade to the location you would like as your intermediate customer preferred position...
  • Page 4 Adjusting the Upper Limit 1) Move the shade to its current upper limit position and let it stop. 2) Press and Hold the UP and DOWN buttons simultaneously until the motor jogs, then release. A jog is a movement in both directions. 3) Adjust to a new upper limit position.
  • Page 5 1) Disconnect power for 2 seconds. 2) Connect power for 5 seconds. Note: Somfy recommends 10-15 seconds but we found 5 seconds to work better. 3) Disconnect power for 2 Seconds 4) Connect power and then leave it on. The motor will rotate in one direction if the shade is between limits or will jog if at one of the programmed stops.
  • Page 6 Intentionally blank...
  • Page 7 Sonesse 30 RTS Instructions...

  • Page 9: Table Of Contents

    Sonesse 30 RTS ORIGINAL INSTRUCTIONS These instructions apply to all Sonesse 30 RTS drives, the different versions of which are available in the current catalogue. CONTENTS 1. Prior information................... 1.1. Field of application................1.2. Liability ....................2. Installation...................... 2.1. Assembly ....................
  • Page 10 Indicates a danger which may result in death or serious injury. PRECAUTION Indicates a danger which may result in minor or moderate injury. CAUTION Indicates a danger which may result in damage to or destruction of the product. © Copyright 2020 SOMFY ACTIVITES SA. All rights reserved.

  • Page 11: Prior Information

    Any operation of the drive outside the field of application described above is prohibited. Such use, and any failure to comply with the instructions given in this guide and in the attached Safety instructions document, absolves Somfy of any liability and invalidates the warranty.

  • Page 12: Installation

    1] Unclip the cover. 2] Clip the new cover on the head. 2.1.2.Preparing the drive CAUTION • Sonesse 30 RTS : interior diameter of the tube has to be Ø27.7 mm or greater. • The crown is mandatory. © Copyright...
  • Page 13 ▪ or by using a wheel lock, for non-smooth tubes. CAUTION The screws or pop rivets must only be fastened on the wheel and not on the drive. © Copyright 2020 SOMFY ACTIVITES SA. All rights reserved.

  • Page 14: Compatible Power Supplies (For Us Only)

    • Light gap reduced: Do not pinch cable or be careful they are not in contact with moving parts. 2.2.Compatible power supplies (for US only) References Designations 1870196 5 motors / Control Distribution panel 1870192 10 motors / Control Distribution panel © Copyright 2020 SOMFY ACTIVITES SA. All rights reserved.

  • Page 15: Wiring

    • Do not use an extension cord. If the power supply cord is too short, have a qualified electrician install an outlet near the motorised product. Connect the drive to the power supply: ▪ Black wire: - ▪ Red wire: + © Copyright 2020 SOMFY ACTIVITES SA. All rights reserved.

  • Page 16: Commissioning

    LED blinks 5 times. b2] Press the Up button on the control point to confirm the direction of rotation. 2.4.3.Setting the end limits NOTICE The end limits can be set in any order. © Copyright 2020 SOMFY ACTIVITES SA. All rights reserved.
  • Page 17 Briefly press the control point Prog. button. →The motorised product briefly moves up and PROG. down to confirm pairing. The control point is recorded “paired” to the motorised product and green LED blinks 5 times. © Copyright 2020 SOMFY ACTIVITES SA. All rights reserved.

  • Page 18: Tips And Advice On Installation

    Readjusting the end limits [} 14] End-limits are not properly Adjust the end-limit adjusted. referring to Readjusting the end limits [} 14] © Copyright 2020 SOMFY ACTIVITES SA. All rights reserved.
  • Page 19 The control point battery is Check the battery of the low. LED doesn't light control point and replace it when any button of a as required. paired control point is pressed. © Copyright 2020 SOMFY ACTIVITES SA. All rights reserved.
  • Page 20 4] To confirm the new position press and hold the My button until the motorised product briefly moves up and down and green LED blinks 5 times. © Copyright 2020 SOMFY ACTIVITES SA. All rights reserved.
  • Page 21 LED blinks 5 times. 4] Press the Up button to check the new rotation direction. The drive rotation direction is reversed. © Copyright 2020 SOMFY ACTIVITES SA. All rights reserved.
  • Page 22 LED starts to blink slowly. 3] Press the Up, My and Down buttons simultaneously, until the motorised product briefly moves up and down, wheel rotation is reversed and green LED blinks 5 times. © Copyright 2020 SOMFY ACTIVITES SA. All rights reserved.
  • Page 23 3 times. → All the settings are erased. Green LED blinks 5 times then orange LED is fixed on. 2.5.8.Temporary sleeping mode CAUTION The motorised product must be programmed. © Copyright 2020 SOMFY ACTIVITES SA. All rights reserved.

  • Page 24: Use And Maintenance

    The drives are designed to work in 2 modes: Tilting mode or Roller mode. This feature allows the drive to be set according to the type of application. NOTICE The drive is set (by default) to work in Roller mode. © Copyright 2020 SOMFY ACTIVITES SA. All rights reserved.

  • Page 25: Controlling Up, Down, My: In Roller Mode

    2] To stop the motorised product, press the My button. 3] (If a My position is recorded) To move the motorised product to the My position, briefly press the My button. The © Copyright 2020 SOMFY ACTIVITES SA. All rights reserved.

  • Page 26: Favourite Position (My)

    1] Press the my button: ð The motorised product starts to move and stops in the favourite position (my). 2] Press and hold the my button until the motorised product briefly moves up and down: © Copyright 2020 SOMFY ACTIVITES SA. All rights reserved.

  • Page 27: Sun Disappearing Position

    Up and Down buttons. 3] Press and hold the My button until the motorised product moves up and down. g The new sun disappearing position is programmed. © Copyright 2020 SOMFY ACTIVITES SA. All rights reserved.

  • Page 28: Sun Function

    ð The motorised product moves to the My position or to its lower end limit if no MY position has been memorized. 2] When the sunlight level falls below the threshold set on the sun sensor: © Copyright 2020 SOMFY ACTIVITES SA. All rights reserved.

  • Page 29: Adjusting The Speed

    Maximum speed is reached when the motorised product moves briefly 3 times in one direction and 3 times in the other direction. Red LED blinks 3 times and 3 times intermittently. © Copyright 2020 SOMFY ACTIVITES SA. All rights reserved.

  • Page 30: Tips And Advice On Operation

    Set the sun disappearing position is not set. position referring to Sun disappearing position [} 21]. NOTICE If the motorised product still does not work, contact a drive and home automation professional. © Copyright 2020 SOMFY ACTIVITES SA. All rights reserved.
  • Page 31 2] Briefly press the Prog. button (B) on the control point to add or delete. g Green LED blinks 5 times. 3.8.3.Adding/Deleting RTS sensors NOTICE Orange LED blinks slowly when adding or deleting an RTS sensor. © Copyright 2020 SOMFY ACTIVITES SA. All rights reserved.

  • Page 32: Technical Data

    Index protection rating IP30 (For indoor use only) Safety level Class III Torque 2 N·m Adjustable speed 6 - 28 rpm Roller speed (by default) 25 rpm Maximum number of associated controls © Copyright 2020 SOMFY ACTIVITES SA. All rights reserved.
  • Page 33 We care about our environment. Do not dispose of the appliance with usual household waste. Give it to an approved collection point for recycling. SOMFY ACTIVITES SA, F-74300 CLUSES as manufacturer hereby declares that the drive covered by these instructions and used as intended according...
  • Page 34 SOMFY ACTIVITES SA 50 avenue du Nouveau Monde F-74300 CLUSES www.somfy.com 5155873A...

Table of Contents