Advertisement

LIE16MU1
1
Index and Conventions
2
Introduction to E16 series
3
SIRIO E, CONDOR E transmitting unit
4
Warnings for use
5
Warnings for maintenance
6
Operation of SIRIO E, CONDOR E transmitting unit
7
Frequencies
8
Settings
9
SIRIO E, CONDOR E transmitting unit diagnostic
In this manual, all important information is indicated using the following symbols and
conventions:
!
abcd. . .
:
WARNINGS
:
TECHNICAL DATA
abcd. . .
Before installing, starting and using the radio remote control, this manual MUST be
read and understood carefully by all people who install, use and carry out
maintenance on the radio remote control.
Follow the indications and warnings
given by the machine producer
regarding the machine controlled
by the radio remote control.
The information contained in this manual
is subject to modification
without notice and is not binding.
1
INDEX AND CONVENTIONS
INDEX
CONVENTIONS
abcd. . .
abcd. . .
by any means without the written permission of Autec
:
ISTRUCTIONS
:
IMPORTANT TEXTS
If this manual is lost or damaged,
ask for a copy from Autec.
Please specify the serial number
of the relative radio remote control.
No parts of this manual may be reproduced
(Including recording and photocopying).
Page
1
2
5
7
8
9
11
12
13
Page 1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the E16 Series and is the answer not in the manual?

Questions and answers

Summary of Contents for AUTEC E16 Series

  • Page 1 The information contained in this manual No parts of this manual may be reproduced is subject to modification by any means without the written permission of Autec without notice and is not binding. (Including recording and photocopying). Page 1...
  • Page 2 MUST ALWAYS be respected. Autec cannot be held responsible if the radio remote control is installed on applications that are different from those permitted or if used in working conditions that do not respect prescribed standard.
  • Page 3 In any cases of emergencies, damaged parts faults or damaged can ONLY be parts, ALWAYS stop replaced by authorised the “machine + radio Autec personnel, and remote control” only using original system until the Autec spare problem has parts. been solved.
  • Page 4 LIE16MU1 E16 SERIES TECHNICAL DATA Frequency range 433.050 ÷434.790 MHz (or 869.7 ÷870 MHz) Programmable radio channel 32 at 433 MHz (or 12 at 870 MHz) Channel spacing 25kHz Hamming distance Probability of non-recognition of error <10 exp-11 Typical working range...
  • Page 5 This manual refers exclusively to the transmitting unit: the installation warnings are given in the receiving unit manual. The E16 series is equipped with a safety function called SAFETY which protects the "radio remote control + machine" system from involuntary movements caused by possible radio remote control faults.
  • Page 6 LIE16MU1 CONDOR E starting keyswitch STOP button green signalling LED identification plate actuators (joystick and selector) START selector technical data plate battery SIRIO E, CONDOR E TRANSMITTING UNIT TECHNICAL DATA NiCd 7,2V - 0,7 Ah or NiMH 7,2V - 1.3 Ah Power supply (battery pack) internal Antenna...
  • Page 7: Warnings For Use

    LIE16MU1 WARNINGS FOR USE VISUALLY NEVER BE POSITIONED FOLLOW all LEAVE the in a way that movements of the transmitting unit permits him to see the machine and its load unguarded when the “machine + radio remote remaining inside a starting keyswitch control”...
  • Page 8: Warnings For Maintenance

    LIE16MU1 WARNINGS FOR MAINTENANCE ENSURE THAT THE BATTERY faults should HAS BEEN REMOVED be repaired by FROM THE TRANSMIT- authorised Autec TING UNIT BEFORE personnel using CARRYING OUT ANY original Autec MAINTENANCE spare parts WORK. only. No particular maintenance needs to be carried out on the transmitting unit, but the...
  • Page 9: Led Signals

    LIE16MU1 OPERATION OF SIRIO E, CONDOR E TRANSMITTING UNIT LED SIGNALS TYPE OF MEANING OF ACTION SIGNAL SIGNAL NECESSARY Slow OPERATION flash NORMAL LOW BATTERY Switch off the COMMAND Fast The transmitter unit transmitter unit ACTIVATION flash switches off approx. 7 and replace the minutes after the LED battery...
  • Page 10: Charging The Battery

    LIE16MU1 CHARGING THE BATTERY To recharge a flat battery, proceed as follows: Insert the battery into its proper battery charger, which should be positioned in an area having a temperature of between +5°C and +35°C. The battery now starts charging, a state signalled by the lighting up of the “ON CHARGING”...
  • Page 11 A radio remote control operating in MANUAL selection mode can operate at a specific frequency. In order to set the frequency selected the dip switch on the transmitter and receiver units must be set. To activate this means of operation contact authorised Autec personnel. Page 11...
  • Page 12 LIE16MU1 SETTINGS DIP SWITCH ON RADIO MODULE The eight dip switches on the transmitter module are for programming various functions and setting the operating frequency. The dip switches must be programmed with the battery removed from the transmitting unit and can be done only by authorised personnel.
  • Page 13 LIE16MU1 TRANSMITTING UNIT DIAGNOSTIC If the “machine+radio remote control” system does not start, check if the problem is caused by the radio remote control or the machine. Before carrying out any verifications, check the functioning of the machine with the cable control panel: - if it does not switch on, the problem lies with the machine itself - if it does switch on, the problem lies with the radio remote control.

Table of Contents

Save PDF