Advertisement
PART Nos
THIS BULL BAR MUST NOT BE FITTED TO AIRBAG EQUIPPED VEHICLES.
FITMENT TO AIRBAG EQUIPPED VEHICLES MAY INTERFERE WITH THE
PROPER OPERATION OF THE AIRBAGS AND MAY RESULT IN SERIOUS INJURY.
TAKE NOTE OF THE FOLLOWING:
• THIS PRODUCT MUST BE INSTALLED EXACTLY AS PER THESE INSTRUCTIONS
USING ONLY THE HARDWARE SUPPLIED.
• IN THE EVENT OF DAMAGE TO ANY BULL BAR COMPONENT, CONTACT YOUR
NEAREST AUTHORISED ARB STOCKIST. REPAIRS OR MODIFICATIONS TO THE
IMPACT ABSORPTION SYSTEM MUST NOT BE ATTEMPED.
• DO NOT USE THIS PRODUCT FOR ANY VEHICLE MAKE OR MODEL, OTHER THAN
THOSE SPECIFIED BY ARB.
• DO NOT REMOVE LABELS FROM THIS BULL BAR.
• THIS PRODUCT OR IT'S FIXING MUST NOT BE MODIFIED IN ANY WAY.
25/10/2008
If you have any queries regarding the installation of this product please contact the distributor from whom it was purchased, or alternatively the ARB office in your state.
Head Office – ARB Corporation Ltd VIC: 42-44 Garden Street, Kilsyth, Victoria, 3137 Tel: (03) 9761 6622 Fax: (03) 9761 6807
WA:(08) 9244 3553 NSW: (02) 9821 3633 ACT: (02) 6280 7475 SA: (08) 8244 5001 QLD: (07) 3872 3872 NT: (08) 8947 2262 TAS: (03) 6331 4190
3414020 Suits standard dual cabs & all single cabs and cab chassis
3414030 Suits 89-91 extra cabs & 4 Runners
3414060 Suits Feb '92 on SR5 4 runners with OE flares
3414070 Suits extra cabs, 4 runners without OE flares & SRS dual
cabs from Feb '92 on
WARNING
Page 1 of 5
3782882
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ARB 3414020
Summary of Contents for ARB 3414020
- Page 1 3782882 If you have any queries regarding the installation of this product please contact the distributor from whom it was purchased, or alternatively the ARB office in your state. Head Office – ARB Corporation Ltd VIC: 42-44 Garden Street, Kilsyth, Victoria, 3137 Tel: (03) 9761 6622 Fax: (03) 9761 6807...
- Page 2 Refit 2 indicator plastic plugs to square holes in indicator brackets in bull bar. Using 2 self-tapping screws from ARB kit and 2 original screws refit indicators into bull bar. Use the 2 original screws where the plastic plugs were fitted and the 2 new screws from the back of the bar through the bracket and into the light.
- Page 3 9. Tighten all bolts and refit shackle pins if fitting to leaf spring model. 10. Fit the new indicators supplied as follows: a. Push plastic plugs into holes in indicator recess in each wing. Put the indicator into the indicator recess and secure in place with the screws supplied.
- Page 4 Place 8mm packers over the winch mounting holes. 9. Place the bull bar on top of the winch and align mounting holes. Using bolts supplied with winch and 3/8” washers in ARB kit, fit and finger tighten the two upper bolts.
- Page 5 RESULT IN OPERATION DANGER AND WINCH FAILURE. Note 1 When fitting the control box under the bonnet ARB bracket number 3751214 is required along with one 1500mm length red cable and two 1500mm black cables. Fit the cables to the winch before mounting the bull bar to the vehicle. Identify and tag the cables with number codes for easier identification later.
Need help?
Do you have a question about the 3414020 and is the answer not in the manual?
Questions and answers