1 Brief Introduction HT2018B/C Series Battery System Tester is a performance testing tool for startup lead- acid batteries. It is a testing tool for measuring the startup process, charging process and battery performance during electric load process. HT2018C has the Bluetooth printing function for startup process test report.
Function keys and test forceps: < > < >: Recurring, decreasing, up and down page keys; <ESC>: Cancel, return key; <ENTER>: Confirm, enter and test key. Intermediate key: Enter the printing interface; Red test clamp: Positive connection test clamp; HT2018B(C) Battery System Tester...
Page 5
Black test clamp: Negative connection test clamp. HT2018B(C) Battery System Tester...
3) According to the nameplate on the battery, press < > < > button to select the quick test or exact test. Select Quick Test here and press <ENTER> to proceed to the next step. Quick Test Exact Test HT2018B(C) Battery System Tester...
Page 7
2. Starting Load 3) According to the nameplate on the battery, press < > < > button to select the quick test or exact test. Select Exact Test here and press <ENTER> to proceed to the next step. HT2018B(C) Battery System Tester...
Page 8
100 % 8) Now press the middle button to enter the print test report interface (refer to Section 5.6), press the < ESC > button will return to step (4). Note: only HT2018C has Bluetooth printing function. HT2018B(C) Battery System Tester...
Page 9
Test Result Comment >80% Good The battery is in good condition. >60% Common The battery condition is acceptable. >45% Attention Battery will be exhausted. Pay attention. <45% Replace Battery is exhausted. Please replace it. 2) Replace HT2018B(C) Battery System Tester...
Attention must be made to good contact so as not to affect test results. 2) Press < > < > button to select Start Load Test, and press <ENTER> to enter the selection, as follows: HT2018B(C) Battery System Tester...
Common need to observe 9.6~10.2V need to be replaced recently Below 9.6V Very Bad need to be replaced immediately 5.4 Maximum Load Test 5.4.1 Preparation before testing If the car is flameout, please start the car. HT2018B(C) Battery System Tester...
Page 12
If the voltage is less than 12.8V (for 6V system, the voltage is less than 6.40V; for 24V system, the voltage is less than 25.60V), please check whether the generator belt is worn out and can not be used, and whether the wire is short-circuit. HT2018B(C) Battery System Tester...
6.6V; for 24V system, the standard minimum voltage is 26.60V), and the minimum voltage is 13.58V. 5) Press the < ESC > button will return to step (2). 5.5.3 Charging system problematic HT2018B(C) Battery System Tester...
12.87 V 588 CCA 4.75 mΩ 100% 100 % 2) Now press the middle button to enter the inquiry “Print the test report?” Press the <ENTER> button to print or press the <ESC> button to exit. HT2018B(C) Battery System Tester...
<ESC> and <ENTER> two buttons more than one second. The device will enter the language switching interface. Press < > < > button to select language, then press <ENTER> button to enter the test interface, or press <ESC> button to exit. HT2018B(C) Battery System Tester...
2) When the battery passes through a high current, the electrode inside the battery will polarize and produce polarization resistance. Therefore, the measuring time must be very short, otherwise the error of the measured internal resistance is very large. 3) The large current will damage the electrodes inside the battery. HT2018B(C) Battery System Tester...
Page 17
1) Using this measurement method can measure almost all batteries, including small capacity batteries. The internal resistance of notebook batteries is measured by this method. 2) Measuring with this method will not cause much damage to the battery itself. HT2018B(C) Battery System Tester...
6V, 12V, 24V battery test √ √ Startup load test √ √ Charging system test √ √ Maximum load test √ √ Prevent reverse function √ √ The cable length 600mm 600mm Size 143×77×28(mm) Weight 270g HT2018B(C) Battery System Tester...