Page 3
▪ Return the part(s) and the completed Warranty Claim Form to Finn Corporation using the return shipping label. (Within 2 weeks) ▪ Tape the Orange identifier sheet, marked with the W/RMA# on the outside of the box you are shipping the defective part(s) to Finn in.
Page 4
(except those referred to herein) that are manufactured any representation or promise on behalf of Finn Corporation or to by Finn to be free from defects in material and workmanship for a modify the terms or limitations of this warranty in any way.
SAFETY FIRST With any piece of equipment, new or used, the most important part of its operation is SAFETY! Finn Corporation encourages you and your employees to familiarize yourselves with your new equipment and to stress safe operation. The first five pages of this manual are a summary of all the main safety aspects associated with this unit.
Practice all other usual and customary safe working precautions; and above all, remember that safety is up to you. The FINN HydroSeeder® is designed to mix and apply water, seed, fertilizer, agricultural lime and hydraulic mulch to the prepared seedbed. The resultant slurry from mixing one or more of the above materials may react causing harmful or deadly gasses within the tank.
Page 9
driver and/or the operator(s). All personnel should 2. Never engage the clutch review and be familiar with stop/start signals between when both the recirculation the driver and operator(s) before going into operation. and discharge valves are Only the operator should be located on the platform closed.
Page 10
29 CFR 1910.146. including the following: 9. It is recommended that only authorized genuine FINN Drain, flush and ventilate tank interior. replacement parts be used on the machine. Turn off engine and disconnect battery cables and perform lockout/tagout procedures.
THE FINN HYDROSEEDER® AND HOW IT WORKS: The Finn HydroSeeder® will apply seed, fertilizer and/or lime, wood fiber mulch, or stabilizing materials in any prescribed or desired combination. The materials placed in the HydroSeeder® slurry-tank are mixed with water and kept in suspension by a dual agitation process, recirculation of slurry and mechanical agitation, thus forming a slurry that is pumped to the discharge assembly and directed onto the seed bed by the operator.
TRUCK MOUNTING CALCULATIONS: (WB x FL) – (WB x FE) = G WB x (RE + HW -RL) = G G + C must be equal to or less than CA (WB x FE) + (G x HW) = FL (WB x RE) + HW x (WB –...
Place hard wood spacers along the length of truck rails or use Finn Spring Mounting Kit (#011562) or equivalent. ATTACHMENTS: 1. Extension hoses for reaching remote areas are available in 50 ft. (15m) lengths. All connections are camlock quick operating fittings.
6. Radio Remote Control. The radio remote control option provides the operator with pump on/off con- trol, throttle control, and engine shutdown at the end of the hose. With control of the engine throttle, the operator can precisely adjust the pump flow to whatever output the situation requires (i.e., for close-up work around buildings).
Turn thumb nut clockwise until stem rises to maximum height. SPRING b) Remove cap and fill cap with sodium (water soluble) base grease. PRESSURE (FINN part number 000698). Do not use lithium base (chassis DISK lube) grease. c) Replace cap.
WARNING: Never engage the slurry pump clutch when both valve handles are positioned as shown Figure 4. Both valves are closed and will result in extreme heat generation that will cause damage or bodily injury if the slurry pump is running. 1.
® The following tables show loading versus coverage rates for the Finn HydroSeeder . Table A shows rates for ®...
Page 19
TABLE A Using Seed, Fertilizer and Mulch Unit Amount of Material in Tank (pounds(kilograms)) Coverage Area (sq. ft.(sq. m.)) Seed Fertilizer Mulch T170 172 (78) 200 (91) 750 (340) 21,780 (2,023) Above Table is based on 1,500 pounds of mulch, 400 pounds of fertilizer and 345 pounds of seed (8 pounds/1,000 sq.
G. Replace nozzle and gasket in discharge boom. 4. Continue filling tank with water. 5. Increase engine speed to full RPM. Governed speed of the engine on the Finn HydroSeeder® should be 2,700 to 2,800 RPM under load. 6. Start loading dry material, loading the lightest material first. Agitator control should be in full reverse for mixing.
C. Fertilizer - Stand over hatch opening and drop the bag onto the bag cutter. Grasp both ends of the bag and dump material. D. All other additives - Consult with manufacturer for proper loading technique. 7. When all materials are loaded and in suspension, and the tank is full, move the agitator to neutral then full speed forward to insure all material is mixed.
APPLICATION OF SLURRY: I. GENERAL APPLICATION TECHNIQUES DANGER: Do not spray toward power lines, transformers or other high voltage con- ductors. CAUTION: The driver of the carrying vehicle should remain alert for hazards to the operator, such as low power lines, hanging branches, etc. Driver should never start or stop abruptly.
A. PUMP TAKE OFF SYSTEM OR HOSE REEL WITH REMOTE VALVE: 1. Open recirculation valve and close discharge valve and close remote valve at the end of the hose. 2. Engage clutch. When stream is flowing freely through the recirculation line, open the pump take off valve.
C. HOSE WORK WITH RADIO REMOTE: 1. Begin with the engine around 1/4 throttle (1,400 RPM). 2. Close recirculation valve. If using an extension hose connected to the discharge boom, open the dis- charge valve. If using the hose reel, close the discharge valve and open the pump take off valve to the hose reel.
6. Move the throttle to approximately 1/2 engine speed. 7. Engage the clutch, and move the throttle to full engine speed. A stream of water should be coming from the end of the recirculation pipe beside the hatch opening, as well as from the boom. 8.
Page 27
2. Plugging or clogging: DANGER: Turn off engine and disconnect battery cables before working on equip- ment. Serious injury or death can result from moving parts or high pres- sure spray. Sometimes when a stoppage occurs, you will not be able to find anything in the line. When this hap- pens, it means that the system became airbound instead of plugged.
Page 28
4. Obstruction in the sump area, which is located at the bottom of the tank on the inside where the suc- tion pipe is attached: A. The easiest way to clear the sump is to back flush through the discharge plumbing with the water supply hose.
Page 29
TROUBLESHOOTING YOUR HYDROSEEDER ® Problem Probable Causes Suggested Solutions Pump loses prime - lacks Too much agitation Slow the agitator distance - leaves excessive Pump worn Reset pump tolerance page 30 amount in tank (100 gal Suction partially plugged Clean out machine see pages 24-25 (378 liters) or more) Nozzle worn or plugged Clean nozzles, replace if necessary...
TROUBLESHOOTING YOUR HYDROSEEDER ® Problem Probable Causes Suggested Solutions PUMP CONT'D: Will not turn Frozen Warm housing to melt ice Jammed with fertilizer or lime Remove cover and clean interior Impeller rusted to suction cover plate Pull cover and remove rust Do not turn the shaft backwards with a pipe wrench - this will unscrew CAUTION: the impeller from the shaft.
12. Add fuel stabilizer to fuel tank. HYDRAULIC SYSTEM: The hydraulic system on your Finn HydroSeeder® is designed to give trouble free service, if maintained. The most important areas of maintenance are the hydraulic oil and filtration. The reservoir holds 22 gallons of Mobil DTE-13M or equivalent hydraulic oil.
CLUMP MAINTENANCE SECTION: Clump maintenance to be done only while engine is not running, and bat- CAUTION: tery cables are disconnected. A. FACTORY-TOLERANCES 1. To check clump tolerances loosen the two clamps on the pump suction piping and remove the inlet elbow.
D. INSTALLING NEW SEAL ASSEMBLY (DO NOT UNWRAP THE NEW SEAL ASSEMBLY UNTIL YOU ARE READY TO INSTALL. ALL PARTS OF THE ASSEMBLY ARE PACKED IN SEQUENCE OF INSTALLATION.) 1. To replace the seal assembly (9), perform the above operations under cleaning and remove pump casing (8) by removing the three bolts (39) holding the clump casing (8) to the clutch body (33).
FUEL TANK POLY HATCH DETAIL DETAIL STRUCTURE & RAILING Ref. No. Part Number Description No. Req’d 012700 Swing Gate 012755 Spring Hinge F330-0108 Main Tank Top F170-0015 Left Rear Toe Rail 008639 Left Rear Guard Rail F170-0038 Tank Top Support 012703 Slide Gate 012737...
Page 50
NOTE: ITEM #1 (DISCHARGE BOOM ASSEMBLY) INCLUDES ITEMS #2 - #7. WHEN ORDERING PARTS, BE SURE TO STATE SERIAL NUMBER OF MACHINE...
VIEW A ENGINE & RADIATOR Ref. No. Part Number Description No. Req’d 075200 Kubota Tier II V3300 Diesel Engine Assembly KU1G521-97010 Fan Belt 075565 1/2" Fan Spacer 075563 Pusher Fan 075562 Radiator 023807 Radiator Cap F816-0008-01 Fan Guard F330-0096 Fan Guard Mounting Strap F170-0042 Top Radiator Mount F170-0014...
Page 54
WHEN ORDERING PARTS, BE SURE TO STATE SERIAL NUMBER OF MACHINE...
ENGINE SHEET METAL Ref. No. Part Number Description No. Req’d 055669 Door Positioning Hinge F260-0006-02 Radiator Cap Cover F260-0006-03 Hinge Spacer F170-0023 Radiator Shroud 075562-01 Radiator Screen F170-0026 Front Sheet Metal Mount F170-0020 Radiator Pan F170-0018 Left Front Engine Foot F170-0019 Right Front Engine Foot 052397...
Page 56
NOTES: ● Air Intake Assembly Includes Items #1-15. ● Item #1 (Air Cleaner Assembly) Includes Items #2-8. ● Exhaust Assembly Includes Items #16-21. WHEN ORDERING PARTS, BE SURE TO STATE SERIAL NUMBER OF MACHINE...
AIR INTAKE & EXHAUST SYSTEM Ref. No. Part Number Description No. Req’d AIR INTAKE ASSEMBLY 012646 Air Cleaner Assembly 012621 Air Cleaner 012623 Safety Filter Element (3.75-E2) 1 per 012622 Main Filter Element (3.75-E1) 1 per 012621D Filter Cap 1 per 012621A Flapper Valve 1 per...
Page 58
WHEN ORDERING PARTS, BE SURE TO STATE SERIAL NUMBER OF MACHINE...
CLUMP, PIPING & DISCHARGE ASSEMBLY Ref. No. Part Number Description No. Req’d 011736 5" Vitaulic Pipe Clamp 011919 Seal For 5" Vitaulic Pipe Clamp 1 Per 008259 5" Dia x 90º Pipe Elbow 0X1232 3/4-10 x 2" Lg. Hex Hd. Cap Screw (Grade 5/Zinc) 012722 Suction Valve Flange Weldment 012058...
Page 62
Pressure Lubricator (Includes Items #41-43) NOTE: Item #15 (10¨ Clutch Assembly Kit) Includes Items #16-39) WHEN ORDERING PARTS, BE SURE TO STATE SERIAL NUMBER OF MACHINE...
CLUMP ASSEMBLY Ref. No. Part Number Description No. Req’d 005146 Suction Cover 005150 O-Ring 005145 Impeller 006443 Mechanical Shaft Seal 005144 Clump Casing 006444 Grease Retainer 005446 Flange Pilot Bearing 012733 Seal 012734 Bearing Retainer Ring 012729 Clump Shaft 012731 Bearing 012732 SN-11 Nut...
Page 64
DETAIL A NOTE: ITEM #13 ALSO NOTE: INCLUDES ITEMS #14. ITEM #9 ALSO INCLUDES ITEMS #10. WHEN ORDERING PARTS, BE SURE TO STATE SERIAL NUMBER OF MACHINE...
CONTROL BOX WIRING Part Number Description No. Req’d 008658 Modified Control Box 008659 Modified Aluminum Subpanel 023802 Safety Switch 045055 30A Panel Mount Circuit Breaker 021198 Flasher 012825 Flasher Mounting Bracket 052118 6 Circuit Fuse Panel 055449 ATO/ATC 10 Amp Fuse 031401 Stud-Type Junction Block (8-Std) 020886...
Page 68
BEARING & SEAL ASSEMBLY 2“ AGITATOR SHAFT THROUGH BACK SIDE NOTE: ITEM #1 (BEARING & SEAL ASSY) INLUDES ITEMS #2 - 9. APPLY (1) SOLID, CONTINUOUS BEAD OF SILICONE ADHESIVE AROUND OUTER EDGE ON THE INSIDE FACE OF THE CLAMPING RING BEFORE INSTALLATION.
AGITATOR & SEAL ASSEMBLY Ref. No. Part Number Description No. Req’d 012529 Bearing and Seal Assembly 012527 Inner Clamping Ring w/Studs 1 per 012528 Agitator Shaft Seal 1 per 012525 Outer Clamping Ring 1 per 012451 Flangette 1 per 012450 2"...
Page 70
WHEN ORDERING PARTS, BE SURE TO STATE SERIAL NUMBER OF MACHINE...
DISCHARGE HOSE EXTENSIONS Part Number Description No. Req’d BOOM TAKE OFF SYSTEM 007930-02 Boom Discharge Extension Hose Assembly As Ordered 007929 1-1/2” x 50 ft. Extension Hose w/ Nipples 1 per 002191 2-1/2" Male Brass Adapter 1 per 160768 2-1/2" to 1-1/2" Reducer Bushing 1 per 010544 2-1/2"...
Page 74
NOTE: ITEM #1 (HOSE REEL ASSEMBLY) INCLUDES ITEMS #2 - 10. DETAIL A DETAIL A WHEN ORDERING PARTS, BE SURE TO STATE SERIAL NUMBER OF MACHINE...
HOSE REEL ELECTRIC MOTOR STARTER CIRCUIT BREAKER 6 GA. RED ENGINE GROUND SOLENOID POWER (See Hose Reel Lead 16 GA. BLUE On Page 54) 6 GA. RED 6 GA. RED 6 GA. BLACK PUSH BUTTON HOSE REEL ASSEMBLY Ref. No. Part Number Description No.
Page 76
17 18 (Inside of Railing - Both Sides of Tank) LEFT SIDE OF UNIT WHEN ORDERING PARTS, BE SURE TO STATE SERIAL NUMBER OF MACHINE...
Page 78
RECOMMENDED SPARE PARTS AND REPAIR KITS Part Number Description No. Req’d RECOMMENDED SPARE PARTS 000698 Pump Seal Lubricator Grease (1 Lb. Can) 011919 Suction Pipe Seal - 5 In. 008472 Suction Pipe Seal - 5 In. x 4 In. Reducer 002820 Discharge Pipe Seal 006722...
Multi-Purpose Grease Cartridge 007469 Lube Sticks For Discharge & Recirculation Valves (Box of 24) 1 012681A Touch-Up Paint (FINN Beige - 4.5 Oz Aerosol) Engine Operator's Manual HydroSeeder® Parts and Operator's Manual WHEN ORDERING PARTS, BE SURE TO STATE SERIAL NUMBER OF MACHINE...
Need help?
Do you have a question about the HydroSeeder T170 and is the answer not in the manual?
Questions and answers