Table of Contents
Related Manuals for LinMot CC-Link IE Field Basic C1250-CC Series
Summary of Contents for LinMot CC-Link IE Field Basic C1250-CC Series
- Page 1 CC-Link IE Field Basic Interface Manual This document applies to the following devices: · C1250-CC-xx-xx-xxx (SG6) (with CC-Link IE Field Basic Interface SW installed) October 2019 Doc.: 0185-1171-E_1V0_MA_CC-Link_IE_Field_Basic...
- Page 2 NTI AG. LinMot® is a registered trademark of NTI AG. Note The information in this documentation reflects the stage of development at the time of press and is therefore without obligation.
-
Page 3: Table Of Contents
5 RT LEDS ............................10 6 INTERFACE ERROR CODES ......................11 7 TROUBLESHOOTING ........................11 7.1 ANALYZING TRAFFIC IN CC-LINK IE FIELD BASIC NETWORKS ..........11 7.2 FREQUENT PROBLEMS AND SOLUTIONS ................11 NTI AG / LinMot Page 3 of 12... -
Page 4: System Overview
1 SYSTEM OVERVIEW The LinMot C1250-CC-xx-xx devices are CC-Link IE Field Basic slaves with the following parameters: Device Property Value Number of occupied stations Standard response time 1ms or less For further information on CC-Link IE Field Basic please visit: https://www.cc-link.org/en/index.html... -
Page 5: Connecting To The Cc_Link Ie Field Basic Network
Station-ID Low Nibble (0 … F). Bit 1 is the LSB, bit 4 the MSB. Setting the Station-ID high & low to 0xFF initiates resetting the drive to manufacturer settings! 3 CC-LINK IE FIELD BASIC PARAMETERS AND VARIABLES NTI AG / LinMot Page 5 of 12... -
Page 6: Parameters
The LinMot-Talk software can be downloaded from http://www.linmot.com. 3.1.1 Dis-/Enable With the Dis-/Enable parameter the LinMot device can be run without the CC-Link IE Field Basic Interface going online. So in a first step the system can be configured and run without any bus connection. -
Page 7: Monitoring Channels
UPID of the parameter channel 5. Channel 6 UPID Defines the source variable by UPID of the parameter channel 6. Channel 7 UPID Defines the source variable by UPID of the parameter channel 7. NTI AG / LinMot Page 7 of 12... -
Page 8: Variables
Value Out 4 MAPPING OF PROCESS DATA The LinMot drive is a CC-Link IE Field Basic slave. To configure it with a CC-Link master, the corresponding CSP+ file is used. The CSP+ File can be found in the installation directory. -
Page 9: Data Received From Plc
TX_Cfg_Module_Control UInt16 TX_Cfg_Module_Index_Out UInt16 TX_Cfg_Module_Value_Out UInt32 1 For a detailed description on how to use this m odule please consult the m anual “LinMot drive Configuration over Fieldbus Interfaces SG5”. 4.2 Data received from PLC Data Type Index Name Data Type... -
Page 10: Rt Leds
UInt16 RX_Cfg_Module_Index_In UInt16 RX_Cfg_Module_Value_In UInt32 1 For a detailed description on how to use this m odule please consult the m anual “LinMot drive Configuration over Fieldbus Interfaces SG5”. 5 RT LEDS Error Codes RT Bus Error Description Station is disconnected. -
Page 11: Interface Error Codes
Check if the Station-ID / IP-Address of the drive matches with the one configured in the PLC. Possible Solution: Check if the Station-ID / IP-Address of the drive is unique, and no other device in the network has the same ID. NTI AG / LinMot Page 11 of 12... - Page 12 LinMot USA Inc. N1922 State Road 120, Unit 1 Lake Geneva, WI 53147 Phone: 262-743-2555 E-Mail: usasales@linmot.com Web: http://www.linmot-usa.com/ Please visit http://www.linmot.com/contact to find the distribution close to you. Smart solutions are... Page 12 of 12 NTI AG / LinMot...
Need help?
Do you have a question about the CC-Link IE Field Basic C1250-CC Series and is the answer not in the manual?
Questions and answers