Table of Contents
Advertisement
2.5 TRANSLATION
The operator must:
• have a general view of the path to be followed;
• stop the manoeuvre in case of hazardous situations.
ATTENTION!
Do not push or pull the appliance to move it,
as it may tip over.
2.6 PLACING THE LOAD
Before placing the load, make sure the way is free and that
the floor is flat and can take the load. Remove the appliance
from the wooden pallet, move it to one side, then slide it
onto the floor.
2.7 STORAGE
The machine and/or its parts must be stored and protected
against damp, in a non-aggressive place free of vibrations and
with room temperature between -10°C and 50°C. The place
where the machine is stored must have a flat support surface
in order to avoid any twisting of the machine or damage to
the support feet.
ATTENTION!
M a ch i n e p o s i t i o n i n g , i n s t a l l a t i o n a n d
disassembly must be carried out by a specialised
technician.
ATTENTION!
Do not make modifications to the parts supplied
with the machine. Any missing or faulty parts
must be replaced with original parts.
•
Do not store or use gasoline or other flammable
vapours, liquids or items in the vicinity of this or any other
appliance.
•
Do not spray aerosols in the vicinity of this appliance while
it is in operation.
•
Never check for leaks with an open flame.
•
The appliance is not suitable for a marine environment.
3. INSTALLATION AND ASSEMBLY
To ensure correct operation of the appliance and maintain
safe conditions during use, carefully follow the instructions
given below in this section.
ATTENTION!
The operations described below must be carried
out in compliance with the current safety
regulations, regarding the equipment used and
the operating procedures.
ATTENTION!
Before moving the appliance make sure the
capacity of the lifting equipment used is suitable
for its weight.
28
3.1 CUSTOMER'S RESPONSIBILITIES
The Customer must:
- prearrange a high-sensitivity manual-reset differential
thermal-magnetic switch. For information regarding the
electrical connection, refer to par. 5.2 "Electrical connection";
- check the flatness of the surface on which the machine is placed.
- prearrange a device lockable in the open position for the
connection to the power supply.
- prearrange the connection to a suitable earthing system
(par. 5.2.3)
- install a rapid gas shutoff cock/valve ahead of each individual
appliance. Install the cock/valve in an easily accessed place.
3.2 MACHINE SPACE LIMITS
A suitable space must be left around the machine (for
operations, maintenance, etc.). This space must be increased
in case of use and/or transfer of other equipment and/or
means or if exit routes are necessary inside the workplace.
RISK OF FIRE - Keep the area around the ap-
pliance free and clear of combustibles.
Do not keep flammable materials in the vicinity
of this appliance.
Install the appliance in a well-ventilated place to
avoid the creation of dangerous mixtures of unburnt gases
in the same room.
Air recirculation must take into account the air necessary for
combustion 2 m³/h/kW of gas power, as well as the well-being
of persons working in the kitchen.
Inadequate ventilation causes asphyxia. Do not obstruct
the ventilation system in the place where this appliance
is installed.
Do not obstruct the vents or ducts of this or other ap-
pliances.
Place emergency telephone numbers in a visible position.
3.3 POSITIONING
The installation diagram provided in this instruction manual
gives the appliance overall dimensions and the position of
connections (gas, electricity, water).
The appliance can be installed separately or combined with
other appliances of the same range.
The appliances are not suitable for recess-mounting. Leave
at least 10 cm between the appliance and side or rear walls.
Suitably insulate surfaces that are at distances less than
that indicated.
Maintain an adequate distance between the appliance and
any combustible walls. Do not store or use flammable mate-
rials and liquids near the appliance.
Install the appliance, taking all the safety precautions required
for this type of operation, also respecting the relevant fire-
prevention instructions.
If the machine is installed in places where there are corrosive
substances (chlorine, etc.), it is advisable to go over all the
stainless steel surfaces with a rag soaked in paraffin oil to
create a protective film.
The machine must be taken to the place of installation and
the packing base removed only when being installed.
Arranging the machine:
• position the machine in the required place;
• adjust the height and levelling with the adjustment feet, also
checking correct door closing
Advertisement
Chapters
Table of Contents
