Related Manuals for SKF Linkoln Pile Driver III C Series
Summary of Contents for SKF Linkoln Pile Driver III C Series
- Page 1 User and maintenance instructions Pile Driver III pump assembly Models 2328, 2356, 84923, series “C” Date of issue February 2018 Form number 404395 Version...
-
Page 2: Table Of Contents
Contents Explanation of Safety safety signals • Read and carefully observe operating instructions before unpacking and Explanation of safety signals ..operating pump. Pump must be operated, NOTE Safety ......maintained and repaired exclusively by Emphasizes useful hints and Gland packing design . -
Page 3: Gland Packing Design
Gland packing Specifications design Pump stroke 6 in (152 mm) Output per cycle 85 in (1 393 cm Operating temperature –30 to +160 °F (–34 to +71 °C) Recommended speed max. 75 cycles/min Many industrial type materials (sealants, Output at 75 cycles/minute 27.6 gal/min (104,5 l/min) adhesives, inks, etc.) display a tendency to Wetted part materials... -
Page 4: Dimensions
Fig. 1 Dimensions Airmotors Airmotors with air brake 86810 94810 84808 94808 84806 94806 84804 94804 84803 Refer to († 404192) Refer to († 422964) ø 3.00 in (76,2 mm) 84923 / in NPTF 20 in (508 mm) ø 0.56 in (14 mm) ø... -
Page 5: Attach Airmotor To Pump Tube
Operation NOTE WARNING precautions Install pump in upright position. Do not exceed stated maximum working Use model 83727 stand pipe for bulk pressure of pump or of lowest rated material dispensing. component in system. Locate pump as close to tank as possible Do not alter or modify any part with minimum 3 in (76 mm) ID inlet hose of equipment. -
Page 6: Pump Prime
Pump prime Disassembly 6 Remove pump tube (15) from outlet body (13). 7 Remove O-ring (14) from To begin operation, pump has to be primed Standard tools required are: outlet body (13). with pumped material. Pile Driver III pump is in wrench (30) 8 Remove bleeder valve (12) from... - Page 7 Fig. IPB 1 Torque to 100–120 lbf-ft (136–163 Nm). Torque to 120–150 lbf-ft (163–204 Nm). Assemble to (17) with #242 Loctite. Torque to 24–26 lbf-ft (33–35 Nm). Install wipers (5) and U-cups (8, 23) in direction shown in enlarged views.
-
Page 8: Parts List
Parts list Item Description Quantity Part number Bolt connector, in hex 236225 Coupling nut, 1 in hex 237051 Gland nut, 4 in flats 272833 Spacer 272835 Wiper 241603 Bushing 272834 O-ring, polyurethane 239921 1) 2) 3) U-cup, polyurethane 239927 1) 2) 3) Sleeve 247272 Washer... -
Page 9: Troubleshooting
Troubleshooting Condition Possible cause Corrective action Pump does not operate. Restricted or inadequate air supply. Check air supply pressure and air hose diameter for minimum air supply hose diameter. Obstructed material output. Check output line for restrictions. Pump speeds up or runs erratically. Pump is not primed. - Page 10 This page left intentionally blank...
- Page 11 This page left intentionally blank...
-
Page 12: Warranty
| lincolnindustrial.com ® SKF and Lincoln are registered trademarks of the SKF Group. © SKF Group 2018 The contents of this publication are the copyright of the publisher and may not be reproduced (even extracts) unless prior written permission is granted. Every care has been taken to ensure the accuracy of the information contained in this publication but no liability can be accepted for any loss or damage whether direct, indirect or consequential arising out of the use of the information contained herein.
Need help?
Do you have a question about the Linkoln Pile Driver III C Series and is the answer not in the manual?
Questions and answers