Riello R32 Series Installation And Technical Service Instructions
Hide thumbs
Also See for R32 Series:
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Riello R32 Series
Summary of Contents for Riello R32 Series
- Page 1 AMD P SERIES R32 INSTALLATION AND TECHNICAL SERVICE INSTRUCTIONS...
- Page 2 While your technical skills and knowledge will certainly be more than sufficient, this booklet contains all the information that we have deemed necessary for the device's correct and easy installation. Thank you again, and keep up the good work. RIELLO COMPLIANCE R AMD P heat pumps are compliant with the following European Directives: —...
-
Page 3: Table Of Contents
AMD P TABLE OF CONTENTS GENERAL INFORMATION ....p. 4 General Notices ......p. 4 Safety precautions . -
Page 4: General Information
GENERAl INfORMAtION GENERAL INFORMATION According to EU Regulation no. 517/2014 regarding certain General Notices fluorinated greenhouse gases, the total amount of refrig- erant contained within the installed system must be indi- cated. This information can be found on the unit technical When you get the product, check immediately that the con- data plate. -
Page 5: Unit Description
GENERAl INfORMAtION Unit description Identification R AMD P is a duct installation indoor unit, suitable for busi- The unit can be identified through the technical data plate: ness premises in combination with the outdoor unit AARIA PRO P with R32 e AARIA PRO with R410A. The multiple-speed fan DC motor improves performance and sound comfort. -
Page 6: Technical Specifications
GENERAl INfORMAtION Air outlet Support bracket Refrigerant connections Electric connection Air filter Condensate drain pipe (collector tray) Wired control panel Technical specifications Model 100 PB 125 PB 140 PB 125 PC 140 PC Electrical characteristics Power supply V/Ph/Hz 230/1/50 Quantity Nominal power input 0,26 0,27... -
Page 7: Cooling Circuit
GENERAl INfORMAtION Cooling circuit Outdoor unit Heat exchanger Indoor unit Heat exchanger sensor Refrigerant connections Electric fan Room air probe Connection pipes... -
Page 8: Installation
The document envelope must be kept in a safe place. Any duplicate must be requested from RIELLO S.p.A. which re- serves to charge the cost. Remove the supplied material and the control panel from... -
Page 9: Storage
INStAllAtION Model 100 PB 125 PB 140 PB Product dimensions 1500 1500 1500 Weight 35,0 52,0 52,0 MODEl 125 - 140 PC Strapping bands Cover Packaging polystyrene protection Packaging paper protection Polyethylene bag Document envelope Follow the below instructions for packing removal and product handling: —... -
Page 10: Recommended Distances
INStAllAtION Minimum floor area for ceiling installation Avoid placing the unit less than 1 metre away from radio and video systems. A min A min m² m² A detachable section cut into the suspended ceiling is re- 2,81 quired in order to access the unit. 3,09 3,38 No requirements... - Page 11 INStAllAtION • Ceiling mounting: MODEl 100 - 125 - 140 PB Model 100 PB 125 PB 140 PB template dimensions Threaded rods 1562 Fastening nut Washer — position the support rods and fix them properly to the MODEl 125 - 140 PC bearing structures —...
-
Page 12: Aeraulic Connection
INStAllAtION — keep a downward inclination toward the external side Model 125 PC 140 PC — insert a plastic tube in the hole in order to protect the con- Air duct dimensions nections 1052 — seal with stucco 1163 Make sure the wall section does not feature pipes or power lines. -
Page 13: Refrigerating Connection
INStAllAtION MODEl 100 - 125 - 140 PB MODEl 125 - 140 PC Ø 123 Fresh air connection — connect a circular duct to the prepared connection Gas line connection — connect the damper motor to the connector provided on Liquid line connection the electronic board —... - Page 14 INStAllAtION Before threading the lines through the hole in the wall, Pipe Ø tightening torque close the lines ends. inches 6,35 9,52 12,70 15,88 — cut the pipe end square using a pipe cutter — remove burrs keeping the cut edge facing down —...
-
Page 15: Condensate Discharge Connection
INStAllAtION Drain with pump (models 100 - 125 - 140 PB only) MODEl 100 - 125 - 140 PB Gas pipe Condensation discharge Liquid pipe Heat insulation Adhesive tape — insulate the liquid and gas pipes separately Condensation drain connection (pump) —... - Page 16 INStAllAtION Drop down discharging Connections MODEl 100 - 125 -140 PB Hose clamp Condensate discharge pipe (supplied) Adapter Drainage pipe Condensation drain connection (drop down) Insulating material Condensate discharge attachment Model 100 PB 125 PB 140 PB — connect the condensate drain pipe Refrigeration characteristics —...
- Page 17 INStAllAtION MODEl 100 - 125 - 140 PB 4 mm Hose clamp Insulating material — insulate the joints Inspection hole 100 mm 50 ~100 mm The discharge system must feature a suitable syphon in or- — charge 1,2 liters of water trough the inspection hole der to prevent air from entering the vacuum system.
-
Page 18: Wiring Diagram
INStAllAtION 2.12 Wiring diagram Model 100 PB INFRARED RICEVITORE REMOTE TELECOMANDO RECEIVER (WITHOUT DIGIT AL DISPALY) MOTORE VENTILATORE FAN MOTOR CN34 CN21 ROOMCARD 12345678 12345678 POMPA SCARICO CN16 CONDENSA PUMP SW01 SW03 CN41 GALLEGGIANTE CN13 SONDA TEMP. ROOM PIPING FLOA T AMBIENTE SONDA TEMP. - Page 19 INStAllAtION Model 125 PB - 140 PB POMPA SCARICO FRELAY FOR MOTORE CONDENSA FRESH AIR ARIA ESTERNA/ PUMP TRASFORMATORE MOTOR SEGN. ALLARME INFRARED RICEVITORE TRANSFORMER (CN7 Contact ESTERNO REMOTE TELECOMANDO rating-230 RECEIVER VAC,3A) / E.A.0 CN19 FUSIBILE MAIN CONTROL FUSE 1234 BOARD T3.15A/250V AC...
- Page 20 INStAllAtION Model 125 PC - 140 PC Reattore CN10 CN32 CN12 Reactor MOTORE FUSIBILE VENTILATORE CN39 FUSE DC FAN MOTOR T8A/250VAC CN16 SW01 R OOM CN37 CARD CONTATTO MAIN CONTROL FINESTRA BOARD FRESH AIR RICEVITORE MOTOR / E.A.O SCHEDA ELETRONICA TELECOMANDO MOTORE PRINCIPALE...
-
Page 21: Electrical Connection
INStAllAtION 2.13 Electrical connection MODEl 100 - 125 - 140 PB AMD P it leaves the factory completely wired, and only requires a connection to the outdoor unit. O F F Electric panel access panel MODEl 125 - 140 PC —... -
Page 22: Control Panel
INStAllAtION Model 100 PB 125 PB 140 PB 125 PC 140 PC Electrical characteristics Power supply V/Ph/Hz 230/1/50 Protection factor n. x Power cable 3 x 4 5 x 4 mm² n. x Signal cable 4 x 2,5 1,5 m mm²... - Page 23 INStAllAtION — make sure that the electrical power supply system is com- pliant with the current national safety standards — for any electrical intervention, always refer to the wiring diagrams contained within this booklet — take anti-static precautions in case of weather conditions where humidity is less than 40% CON1 Electric connections shall be made in compliance with na-...
- Page 24 INStAllAtION functions Allows you to switch the display off and on Access to the following functions is performed sequentially by pressing the key and work on Allow to select the operating mode Detected ambient humidity Decreases the value of the selected parameter Value of the desired humidity when pressing the increase and decrease keys Increases the value of the selected parameter...
-
Page 25: Commissioning And Maintenance
COMMISSIONING AND MAINtENANCE COMMISSIONING AND MAINtENANCE — all distances have been respected Preparation for first commissioning — all connections have been properly completed — power supply values are correct. Prior to commissioning, it is necessary to check that: — the earthing has been carried out correctly —... -
Page 26: Putting Into Service
COMMISSIONING AND MAINtENANCE — the unit turns off automatically, if the contact is clean SW1 (BM1)-5 “Roomcard” opens, but can be controlled by a remote Heat pump operation (OFF) or only cooling operation (ON). control Factory set is heat pump (OFF). —... -
Page 27: Temporary Shutdown
COMMISSIONING AND MAINtENANCE The compressor activates 3 minutes after unit activation. Do not open the access covers and carry out technical or cleaning activities before disconnecting the unit from the power grid by positioning the system's main switch in the Refer to the user booklet as for the use of the remote control. -
Page 28: Alarms
COMMISSIONING AND MAINtENANCE Alarms In the presence of operating abnormalities, the unit is secured • To display the code: and blocked. — press for 5 seconds Safety block can occur randomly. • The code is displayed in the top left corner: –... - Page 29 COMMISSIONING AND MAINtENANCE AMD 125 PC - AMD 140 PC LED1 Display Description Remarks Sensor disconnected Broken sensor Room probe fault Incorrect position Probe short circuit Sensor disconnected Sensor damaged Exchanger probe fault Incorrect position Probe short circuit Microprocessor disconnected Microprocessor fault Microprocessor malfunction Programming error...
-
Page 30: Disposal
RECYClING AND DISPOSAl DISPOSAl Packaging materials shall be disposed of separately so as to re- cover and recycle them. At the end of its service life, the device shall be disposed of according to the existing legislation. - Page 32 RIELLO S.p.A. - 37045 Legnago (VR) tel. +39 0442 630111 - fax +39 0442 630371 www.riello.it As the manufacturer is constantly improving its products, the aesthetic or dimensional features, the technical data, the equipment and accessories indicated could be subject to variations.