Table of Contents
Advertisement
• Thank you very much for purchasing this product.
• To ensure correct and safe usage with a full understanding of this product's performance, please be sure to read
through this manual completely and store it in a safe location.
• Unauthorized copying or transferal, in whole or in part, of this manual is prohibited.
• The specifications of this product and the contents of this operation manual are subject to change without
notice.
• This manual and the product have been prepared and tested as much as possible. If you find any misprints or
errors, please inform Roland DG Corporation.
• Roland DG Corporation assumes no responsibility for any direct or indirect loss or damage that may occur
through use of this product, regardless of any failure to perform on the part of this product.
• Roland DG Corporation assumes no responsibility for any direct or indirect loss or damage that may occur with
respect to any article made using this product.
FA02569/R1-210423
Installation Guide
Advertisement
Table of Contents
Related Manuals for Roland Camm-1 GR2-640
Summary of Contents for Roland Camm-1 GR2-640
- Page 1 • Roland DG Corporation assumes no responsibility for any direct or indirect loss or damage that may occur with respect to any article made using this product.
-
Page 2: Table Of Contents
Uninstalling GreatCut-R ..................... 32 Copyrights and property of this software and this manual belong to Roland DG Corporation. No part of this soft- ware or publication may be reproduced, stored in a retrieval system, or transmitted—in any form or by any means, electronic, mechanical, photocopy, recording, or otherwise—without the prior written permission of the publisher. -
Page 3: Installation And Settings
1. Installation and Settings Introduction ......................3 Downloading Software ................... 3 Software License Registration ................ 4 1. Network Settings (LAN Connection) ..............6 Determining the Network Addresses ............. 6 Setting the Computer's Network..............6 Setting the Cutting Machine's Network ............8 2. Installing the Driver ..................... -
Page 4: Introduction
Introduction Downloading Software The software (Windows driver and application software) required to use the machine can be down- loaded from the following URL. After downloading the software, install it on your computer. https://downloadcenter.rolanddg.com/GR2-640 Installable Software This is a Windows-based driver required for sending data from a computer to the machine. -
Page 5: Software License Registration
Introduction Software License Registration To use GreatCut-R as its regular edition, access the following URL and register your license. https://rolandvoucher.eurosystems.lu/ ME MO License registration requires a voucher code, so make sure it is ready. Voucher code This code is the alphanumeric character string starting with "KROL" and consisting of four charac- ters-five characters-five characters-five characters-five characters. - Page 6 Introduction Enter the items indicated with the mark. Click [Request license code]. The registration information is sent to the software administrator, and the following message appears. ME MO Two email messages are sent to the registered address upon the completion of license registra- tion.
-
Page 7: Network Settings (Lan Connection)
1. Network Settings (LAN Connection) The examples used in the procedures for making the settings described in this section assume you are using one computer and one machine. The settings listed here are only an example. The pro- cedure and settings given in this manual do not match every environment. If the computer you're using is connected to a number of networked devices or to the Internet, incorrect settings may ad- versely affect the entire network. - Page 8 1. Network Settings (LAN Connection) Select [Internet Protocol Version 4 (TCP/IPv4)], and then click [Properties]. If the [Internet Protocol Version 4 (TCP/IPv4)] check box was clear, click the check box to select Select [Use the following IP address], and then enter the network address you deter- mined under P.
-
Page 9: Setting The Cutting Machine's Network
1. Network Settings (LAN Connection) Setting the Cutting Machine's Network Procedure Switch on the power. Remove any material loaded in the machine. Press [MISC] on the operation panel when the following screen appears. If the paper sensor detects material, the following screen does not appear. Off Line Setup Mode Press [ ] several times to display the screen shown below. -
Page 10: Installing The Driver
2. Installing the Driver This section explains the procedure for installing the cutting machine driver on the computer. You can connect this machine to the computer using a USB cable, Ethernet cable, or RS-232C cable. ME M O The driver cannot be installed if material is detected by the machine's paper sensor. Install the driver before setting up the material in the machine. - Page 11 3. Installing the Driver Click [OK]. Check that all other applications have been shut down, and then click [OK]. The installation begins. If the driver is already installed, the following screen will appear. Click "Yes." When the following message appears, click [OK]. The driver installation is finished.
- Page 12 3. Installing the Driver To install AAS II VBA in CorelDRAW and Adobe Illustrator, click [Install] when the fol- lowing screen appears. When the following screen appears, the installation is finished. Click [OK]. 1.Installation and Settings...
-
Page 13: Installing The Driver (Lan Connection)
3. Installing the Driver Installing the Driver (LAN Connection) Procedure Start Windows and log on as the "Administrator" or an "Administrators" account. Shut down all other programs. Open the downloaded folder, and then double-click "Cutter_Plotter_driver.exe." The file name extension (.exe) may be hidden. If a "User Account Control"... - Page 14 3. Installing the Driver Select the model of the machine, and then enter its IP address, which you determined under P. 6 "Determining the Network Addresses" Click [Save]. The installation begins. If the driver is already installed, the following screen will appear. Click "Yes." When the following message appears, click [OK].
-
Page 15: Installing The Driver (Rs-232C Connection)
3. Installing the Driver When the following screen appears, the installation is finished. Click [OK]. Installing the Driver (RS-232C Connection) Procedure Start Windows and log on as the "Administrator" or an "Administrators" account. Shut down all other programs. Open the downloaded folder, and then double-click "Cutter_Plotter_driver.exe." The file name extension (.exe) may be hidden. - Page 16 3. Installing the Driver Check that all other applications have been shut down, and then click [OK]. Select the communication port on the computer, and then use [Machine] to select the model of the machine. Click [Install]. The installation begins. If the driver is already installed, the following screen will appear.
- Page 17 3. Installing the Driver To install AAS II VBA in CorelDRAW and Adobe Illustrator, click [Install] when the fol- lowing screen appears. When the following screen appears, the installation is finished. Click [OK]. Setting RS-232C Communication Check the communication settings of the machine and ensure they are the same as those of the computer.
- Page 18 3. Installing the Driver To change communication settings, press [ ] or [ ] and select from the following combinations. Panel display • 9600, n, 7, 1, p • 19200, n, 7, 1, p • 9600, o, 7, 1, p •...
- Page 19 3. Installing the Driver Click [Ports (COM & LPT)], and then click [Communications Port (COM1)] or [Commu- nications Port (COM2)]. If [Ports (COM & LPT)] is not displayed in [Device Manager], turn on [Show hidden devices] in the [View] menu. Select the port connected to the RS-232C interface for the communication port. Select the [Port Settings] tab, and then select the same values as the communication settings for the machine set in step Select [None] for [Flow control].
-
Page 20: Installing The Software
3. Installing the Software Installing GreatCut-R Procedure Start Windows and log on as the "Administrator" or an "Administrators" account. Shut down all other programs. Open the downloaded folder, and then double-click "greatcut-r.exe." The file name extension (.exe) may be hidden. If a "User Account Control"... - Page 21 3. Installing the Software Check the installation folder, and then click [Next]. You can also click [Browse] to specify the installation folder. Specify the folder to save, and then click [Next]. To create a desktop icon, click [Yes] on the following screen. 1.Installation and Settings...
- Page 22 3. Installing the Software Click [Install]. The installation starts. Wait until the operation finishes. When the following screen appears, click [Finish]. The installation is finished. Select the [Start GreatCut-R] check box and exit the installer to start GreatCut-R and display the license authentication screen.
-
Page 23: Performing License Authentication
3. Installing the Software Performing License Authentication The license authentication screen appears the first time GreatCut-R starts. Perform license authenti- cation within 30 days of installing the software. Each computer requires a separate license to install this software. Click [License File], and then select the license file (.ecf) provided upon the completion of license registration. - Page 24 3. Installing the Software Entering License Information Manually Procedure Click [License] on the license authentication screen. Select [Enter license data], and then click [Continue]. The screen for entering the license information appears. Follow the link in the activation email sent upon the completion of license registration and enter the provided license information.
-
Page 25: Setting The Greatcut-R Connection Method
3. Installing the Software Setting the GreatCut-R Connection Method Set the device that will receive the jobs sent from GreatCut-R. Procedure Start GreatCut-R. From the [Settings] menu, click [Standard Settings], and then click [Output Devices]. The [Setup Device] screen appears. Use the [Driver] list to select the machine model. - Page 26 Introduction Configure the basic settings for output. For details on these settings, refer to the GreatCut-R online help. ME MO To add an output destination machine or to change the IP address, click under [Current Output Device], select [Add local device] or [Change] (respectively), and then configure the settings in the same manner as steps 1.Installation and Settings...
-
Page 27: What To Do If
2. What to Do If Driver ........................27 The Driver Cannot Be Installed Correctly (USB Connection) ......27 Uninstalling the Driver ................. 29 Other Information....................31 Updating the Automatic Aligning System (AAS) Plugin ........ 31 Uninstalling GreatCut-R ................32 2.What to Do If... -
Page 28: Driver
Driver The Driver Cannot Be Installed Correctly (USB Connection) When a USB cable is connected to the machine and a computer, the connection is detected auto- matically and [USB Printing Support] is displayed under [Universal Serial Bus controllers] in "Device Manager."... - Page 29 Driver Right-click [USB Printing Support], and then click [Properties]. Check that "Microsoft" is displayed for [Manufacturer] on the [General] tab. If you cannot confirm that this item is displayed with steps At the same level as [Universal Serial Bus controllers], click [USB devices], right- click [USB PRINTER], and then click [Properties].
-
Page 30: Uninstalling The Driver
Driver Uninstalling the Driver When updating the driver to a new version or reinstalling it, the installed driver must be completely removed from the computer. When uninstalling the driver, perform the following procedure. Procedure Turn off the machine. Disconnect the USB cable if it is connected. Log on to Windows as the "Administrator"... - Page 31 Driver Select the driver of the machine, and then click [Remove]. Select [Remove driver and driver package], and then click [OK]. When a removal confirmation dialog box appears, click [Yes]. When the following screen appears, click [Delete] then [OK]. The driver installed on the computer is completely removed. 2.What to Do If...
-
Page 32: Other Information
Other Information Updating the Automatic Aligning System (AAS) Plugin If Adobe Illustrator or CorelDRAW is upgraded after installing the machine's driver, follow the proce- dure below to reinstall AAS II VBA. Procedure Display the "Devices and Printers" screen. Windows 10: From the [Start] menu, click [Windows System], [Control Panel], and then click [View devices and printers]. -
Page 33: Uninstalling Greatcut-R
Other Information Uninstalling GreatCut-R Delete the target program by following the procedure exactly. Procedure Start Windows and log on as the "Administrator" or an "Administrators" account. Shut down all other programs. Display the screen for uninstalling programs. Windows 10: From the [Start] menu, click [Windows System], [Control Panel], and then click [Unin- stall a program]. - Page 34 Other Information When the following screen appears, click [OK]. 2.What to Do If...