Table of Contents
Advertisement
THREADED HOLES ON
RIGHT SIDE WHEN FACING
SPEAKER FRONT
ROTATED VIEW
STEP 1
STEP 1
ATTACH THREADED ROD TO YOKE AS SHOWN
1/2" FLAT WASHER
LOCK WASHER, AND NUT
**TIGHTEN THESE
REAR BOLTS 1ST**
1/2" NUT
TIGHTEN THESE
INNER NUTS LAST
STEP 2
POLE MOUNT YOKE TO POLE AS SHOWN
POINT YOKE WHERE AUDIO NEEDS TO GO
P P a a r r t t # # - - 0 0 A A - - 1 1 7 7 5 5 6 6 - - 0 0 0 0 7 7 9 9
V V e e r r s s i i o o n n - - 0 0 1 1 . . 5 5
1/2" NUT
1/2" NUT
1/2" FLAT WASHER,
LOCK WASHER, AND NUT
TIGHTEN THESE TOGETHER
TOP VIEW
STEP 1
1/2" THREADED ROD
REAR MOUNTING ANGLE
VERTICAL POLE
SPEAKER YOKE
AUDIO
DIRECTION
THREADED HOLES ON
TOP VIEW
RIGHT SIDE WHEN FACING
SPEAKER FRONT
STEP 2
D D e e s s c c r r i i p p t t i i o o n n - - P P O O L L E E M M T T G G ; ; S S P P K K - - C C X X - - 1 1 0 0 0 0 1 1 , , U U P P T T O O 1 1 5 5 . . 5 5 " " D D I I A A M M E E T T E E R R
USE DAKTRONICS LABEL
CENTER THREADED RODS
ON YOKE WITH ENOUGH GAP
BETWEEN TO GO AROUND POLE
3/8" FLAT WASHER,
LOCK WASHER, AND BOLT
***CRITICAL***
DO NOT USE ANY LUBRICANT
ON ANY MOUNTING HARDWARE
OR WARRANTY WILL BE VOIDED
NOTES:
- BOLT TORQUE: 30 FT-LB
- THREADED RODS RUN ALONG BOTH SIDES OF POLE
- NO DRILLING NECESSARY
ROTATED VIEW
STEP 2
REFERENCE DWG-4561929 FOR
DETAILS ON AIMING SPEAKER
L L i i f f e e c c y y c c l l e e S S t t a a t t e e - - F F u u l l l l P P r r o o d d u u c c t t i i o o n n
TO AIM SPEAKER
#8-32 SCREW
SIDE VIEW
STEP 3
STEP 3
MOUNT SPEAKER TO YOKE
ROTATED VIEW
STEP 3
REV:
DATE:
01
10 DEC 19
THE CONCEPTS EXPRESSED AND DETAILS SHOWN ON THIS DRAWING
SPORTSOUND SYSTEMS
PROJECT:
POLE MOUNTING; 15.5"DIAMETER AND UNDER; SPK-CX
TITLE:
04-NOV-19
DATE:
1/10
SCALE:
DOPPELT
DESIGN:
DOPPELT
DRAWN:
L L a a s s t t M M o o d d i i f f i i e e d d B B y y - - d d o o p p p p e e l l t t
THREADED HOLES ON
RIGHT SIDE WHEN FACING
SPEAKER FRONT
BY:
DESCRIPTION:
DRO
PER CN-91941, UPDATED HARDWARE SIZE FOR SPEAKER
4920
THIRD ANGLE PROJECTION
ARE CONFIDENTIAL AND PROPRIETARY. DO NOT REPRODUCE BY
ANY MEANS WITHOUT THE EXPRESS WRITTEN CONSENT OF
DAKTRONICS, INC. OR ITS WHOLLY OWNED SUBSIDIARIES.
COPYRIGHT 2019 DAKTRONICS, INC. (USA)
INCHES [MILLIMETERS]
DIM UNITS:
SHEET
REV
DO NOT SCALE DRAWING
1 OF 1
01
4306807
JOB NO.
FUNC - TYPE - SIZE
P1870
F - 10 - B
L L a a s s t t M M o o d d i i f f i i e e d d - - 2 2 0 0 1 1 9 9 - - 1 1 2 2 - - 1 1 8 8
Advertisement
Table of Contents
