Table of Contents
Advertisement
DH
SSR-AM
ANNOUNCER'S MIXER KIT
0A-1756-0047
ANNOUNCER'S
HEADSET
A-2382
REAR VIEW
ANNOUNCER'S
MIXER
A-2382
A/C
CHASSIS
SETUP
OUTPUT
PAD
MIX
PHONES
MIC
12VAC
GND
SELECTOR
ON
OUTPUT
OUT
INPUT
600mA
LFT
OFF
120 VAC
CIRCUIT
XLR CABLE PROVIDED WITH ONE OF THE FOLLOWING CONTROL SYSTEM OPTIONS;
SSR-AM (12 FOOT CABLE)
SSR-100 (25 FOOT CABLE)
SSR-200 (25 FOOT CABLE)
XLR PINOUT:
PIN1 = SHLD
CONNECT TO SSR CONTROL
SYSTEM OUTPUT
PIN2 = + (RED)
PIN3 = - (BLK)
LAYOUT VIEW
SIGNAL INPUT PLATE
EC-1244
AMPLIFIER SIGNAL INPUT
CONNECTOR DETAIL
RED
BLK
SHLD
SIGNAL CABLE TERMINATION DETAIL
PT-1024 (SMALL GREEN HEATSHRINK)
PT-1009 (3/16" BLACK HEATSHRINK)
SHLD
BLK
RED
0.25"
1"
LOCAL JUNCTION BOX (LJB#) INSTALLATION DETAILS
-ATTACH SUPPLIED METAL MOUNTING TABS TO LJB#
(EC-1166) WHERE NECESSARY, OPPOSITE CORNERS
OF BOX PREFERRED.
EC-1176
-USE SUPPLIED 0.5" PLASTIC PLUG TO SEAL REAR
0.5" CABLE STRAIN RELIEF
THREADED CONDUIT CONNECTION, USE SILICONE IN
PLUG THREADS.
EC-1166
-INSTALL EC-1176 IN TOP AND BOTTOM OF BOX
1-GANG STEEL OUTDOOR ELECTRICAL BOX
-ROUTE SPEAKER WHIP AND FIELD INSTALLED
SPEAKER CABLE INTO JUNCTION BOX AS SHOWN.
*USE SUPPLIED PLUG TO SEAL HOLE*
-FOLLOW SPEAKER CABLE TERMINATION DETAIL FOR
CABLE/WIRE STRIP LENGTHS
-CONNECT WIRES AS SHOWN USING E-1184
E-1184
-INSTALL BLANK FACEPLATE WITH GASKET (EC-1081)
WIRE NUTS
-BOX MOUNTING HARDWARE PROVIDED BY OTHERS
TO SJB1
W-1745
SPEAKER CABLE
CIRCUIT 1
TOTAL POWER REQUIREMENTS:
SYSTEM VOLTAGE
120
NUMBER OF POLES
MAXIMUM WATTS
AMPERES PER LINE
W-1615, AUDIO SIGNAL CABLE, FIELD INSTALLED,
FROM EC-1244 TO ROUTABLE INPUT 1 ON AMPLIFIER
EC-1008 @2
30.2"
POWER NOTE:
-3' LOCKING POWER CORD INCLUDED WITH AMPLIFIER RACK
-DEDICATED 20A 120VAC CIRCUIT MOUNTED IN RACK
RECOMMENDED WITH DUPLEX OUTLET
-P-1127 (N5-15) PLUG PROVIDED IF POWER CORD NEEDS TO BE
ROUTED OUTSIDE OF RACK, USE EC-1008 FOR CABLE STRAIN RELIEF
PERMANENT MOUNTED AMPLIFIER RACK
AMPLIFIER REAR VIEW
AMPLIFIER TO SPEAKER
WIRING CHART
AMPLIFIER PIN T#
(CH A+) - T1
(CH A-) - T2
(CH B+) - T3
(CH B-) - T4
(CH C+) - T5
(CH C-) - T6
(CH D+) - T7
(CH D-) - T8
TO SPEAKER
RED
EC-1081
SPEAKER CABLE TERMINATION DETAIL; W-1745
1-GANG
COVER
BLK
2.0"
(+) RED
(-) BLK
0.33"
EC-1176
INDOOR MOUNTED EQUIPMENT
2
WIRES + GND
1
1300W
10.8A
(PAR1)
RACK IS SURFACE MOUNTED TO WALL
RACK DEPTH = 7.9"
24.5"
EC-1131
LAYOUT VIEW
0A-1756-0075
SPEAKER
SPK WIRE
WIRE
COLOR
SPK 1 +
RED
SPK 1 -
BLACK
SPK 2 +
RED
SPK 2 -
BLACK
SPK 3 +
RED
SPK 3 -
BLACK
SPK 4 +
RED
SPK 4 -
BLACK
OUTDOOR MOUNTED EQUIPMENT
LOCAL JUNCTION
BOX;
0A-1756-0081
SPEAKER ASSEMBLY;
(LJB1)
SEE (LJB#) DETIALS
(LJB2)
(LJB3)
W-1745, 1 PAIR, 12AWG, SPEAKER WIRE, TYP.
FIELD INSTALLED
MAX LENGTH = 250 FT PER SPEAKER (PROVIDED)
(LJB4)
SPORTSOUND
OUTDOOR AUDIO SYSTEM
SS-200
0A-1756-0074
SUBMITTAL APPROVAL
30' SPEAKER WHIP INCLUDED
APPROVED
APPROVED AS NOTED
APPROVED AS NOTED & RESUBMIT
W/ SPEAKER, TYP.
SPEAKER #1 (SPK1)
COMPANY:
SIGNED:
TITLE:
DATE:
SPEAKER (SPK#) NOTES: 0A-1756-0074
1. SPEAKER ENCLOSURE PROVIDED BY DAKTRONICS AND
INSTALLED BY INSTALL SUBCONTRACTOR.
SPEAKER WEIGHT WITHOUT MOUNT = 55 LBS ea .
2. 30 FOOT 12AWG, W-1745, SPEAKER CABLE WHIP
PRE-TERMINATED TO SPEAKER ENCLOSURE FOR FIELD
TERMINATION TO LOCAL JUNCTION BOX (LJB#).
3. 250 FOOT COIL OF W-1745 PROVIDED WITH EACH SPEAKER
(OPTIONAL) SPEAKER #2
FOR LJB# TO SJB1 CONNECTION. CUT TO LENGTH AFTER
(SPK2)
INSTALLATION.
4. IF SPEAKER IS MOUNTED WITHIN 30 FEET OF PERMANENT
AMP RACK (PAR1), WIRE CAN BE ROUTED DIRECTLY TO
PAR1, LOCAL JUNCTION BOX (LJB#) MAY NOT BE NEEDED.
5. MOUNTING YOKE PROVIDED WITH EACH SPEAKER.
SECONDARY BRACKETS WILL BE PROVIDED BASED ON SITE
SPECIFIC NEEDS; POLE VS ROOF, WALL, OR SOFFIT
MOUNTING.
SEE DWG-04306807 FOR POLE MOUNTING DETAILS.
SEE DWG-04561669 FOR ROOF, WALL, OR SOFFIT MOUNTING
DETAILS.
6. SYSTEM MAY CONTAIN ONE (1) TO FOUR (4) SPEAKERS
LOCAL JUNCTION BOX (LJB#) NOTES: 0A-1756-0081
(OPTIONAL) SPEAKER #3
(SPK3)
1. 1-GANG, LOCAL JUNCTION BOX (LJB#) PROVIDED WITH EACH
SPEAKER.
2. MOUNTED WITHIN RANGE OF PROVIDED
SPEAKER WHIP (30 FEET).
3. SEE LJB# INSTALLATION DETAILS
PERMANENT AMPLIFIER RACK (PAR1) NOTES: 0A-1756-0075
1. PERMANENT AMPLIFIER RACK PROVIDED BY DAKTRONICS.
PERMANENT AMP RACK WEIGHT = 65 LBS .
2. DO NOT ALLOW AMPLIFIER RACK TO GET WET . MOUNT
INDOORS ONLY.
3. ANY CONTROL SYSTEM (SSR-###) CONNECTED TO
ROUTBALE INPUT 1 OR ROUTABLE INPUT 2 WILL BE SENT TO
(OPTIONAL) SPEAKER #4
ALL FOUR SPEAKER OUTPUTS. SSR-AM IS SHOWN ON THIS
(SPK4)
DRAWING, BUT ANY SSR CONTROL SYSTEM CAN BE USED
WITH SS200 SYSTEM.
W-1745 DETAILS;
1 PAIR, 12 AWG, SPEAKER CABLE
OUTER DIAMETER = 0.352"
COLOR = BLACK
RATED FOR DIRECT BURIAL AND OUTDOOR USE, CONDUIT
NOT NECESSARY, IF CONDUIT IS USED SIZE ACCORDING TO
SITE CONDITIONS
W-1615 DETAILS;
1 PAIR, 22AWG WITH SHIELD, AUDIO SIGNAL CABLE
OUTER DIAMETER = 0.170"
COLOR = BLACK
CONDUIT TO BE USED AND SIZED ACCORDINGLY TO SITE
CONDITIONS
SEE DD4310070 FOR SYSTEM MANUAL
SEE DWG-04275565 FOR SYSTEM SCHEMATIC
THE CONCEPTS EXPRESSED AND DETAILS SHOWN ON THIS DRAWING
THIRD ANGLE PROJECTION
ARE CONFIDENTIAL AND PROPRIETARY. DO NOT REPRODUCE BY
ANY MEANS WITHOUT THE EXPRESS WRITTEN CONSENT OF
DAKTRONICS, INC. OR ITS WHOLLY OWNED SUBSIDIARIES.
COPYRIGHT 2019 DAKTRONICS, INC. (USA)
SPORTSOUND SYSTEMS
PROJECT:
RISER; SS-200, ELECTRICAL, PERMANENT SYSTEM
TITLE:
8 OCT 19
INCHES [MILLIMETERS]
DATE:
DIM UNITS:
SHEET
REV
NONE
DO NOT SCALE DRAWING
00
SCALE:
4306294
DESIGN:
CBRANDT
JOB NO.
FUNC - TYPE - SIZE
DRAWN:
CBRANDT
P1756
F 01 D
-
-
Advertisement
Table of Contents
