® 2000HD Audio System. For additional information regarding safety, installation, operation, or service, refer to the telephone numbers listed in Section 7: Daktronics Exchange and Repair & Return Programs (p�26). This manual is not specific to a particular installation. Important Safeguards Read and understand all instructions before beginning the installation process�...
2465 component is not found in the Replacement Parts (p�25), use 02/19/12 Rev. 1 the label to order a replacement. Refer to Section 7: Daktronics Exchange and Repair & Return Programs (p�26) if replacing or Figure 2: Part Label repairing any component.
Sound System Components Equipment Overview The Sportsound 2000HD audio system consists of the following elements: • Sound Cabinet Note: All products in this system are tested individually for • Fiber Conversion Box product safety approval. • Audio Control Rack •...
Cable specifications are as follows: • Minimum 2-core, multimode 50-micron fiber optic cable from fiber conversion box to the sound cabinet. If included with a Daktronics scoreboard or display, the sound system may share a fiber optic cable run, requiring additional cores. •...
Refer to DWG-330901 in Appendix A. Lift the Cabinet The Sportsound 2000HD cabinet is shipped with four (4) 5/8" lift eyes for lifting it into place (Figure 6). Note: The two smaller front lift eyes are meant only for removing the grille frame and not for lifting the cabinet.
Figure 8. Figure 8: Eyebolt Plane Load Note: Daktronics assumes no liability for damages resulting from incorrect setup or lifting methods. Eyebolts are intended for lifting only. Do not attempt to permanently support the cabinet by the eyebolts or eyebolt holes.
Aim the Speakers Reference Drawings: Speaker Adjustment Chart; 2000HD ............... DWG-1023805 Once the cabinet has been mounted in place, it may be necessary to adjust the direction of the speakers for the individual facility. DWG-1023805 in Appendix A provides speaker aiming instructions as well as recommended angles to position the speakers, based on the cabinet’s location in relation to the seating area(s).
System Riser; Electrical & Audio Notes ............. DWG-985713 Schematic; Control Enclosure/Sound Cabinet 2000HD ....... DWG-1082599 DWG-984140 details power and signal connections of the Sportsound 2000HD sound system. To gain access to internal power and signal connection points, open the far right rear access door (Figure 9).
(FCC2). Refer to Detail “C” and Detail “E” of DWG-984140. If there is no fiber splice box, the fiber is terminated directly to the media converter. If included with a Daktronics scoreboard or display, the sound system may share a fiber optic cable run, requiring additional cores.
Page 15
120/240 VAC XLR Audio IN Power IN (From Source) Fiber & Analog OUT (To Fiber Splice Box / Control Enclosure) Figure 12: External Fiber Conversion Box Connections Analog Backup - SWT2 Power Supply - PWS1 Media Converter - FCC2 (To Control Enclosure) (A-2238) (A-2580) Analog to Digital...
If the grille mesh fades or tears over time, or if new graphics/logos are desired, it may be replaced. Only qualified sign companies should be used to replace the grille mesh. Refer to DWG-983337 for mesh layout. Contact Daktronics for mesh reordering. 1� Remove Mesh Frame The front of the sound cabinet has a removable aluminum frame that secures the grille mesh (Figure 14).
Page 17
Tension Clip and rotate/tilt 3� Attach New Mesh Figure 15: Removing Tension Clips When ordered through Daktronics, the mesh has a line with a series of tick marks printed on the front (Figure 16). These tick marks indicate the location of the tension clips and mandrels.
Page 18
d� Continue to place a mandrel and tension clip on every tick mark. e� Lay the mesh across the frame and snap each clip into the tension channels (Figure 19). f� Pull on the corners of the mesh to remove any wrinkles.
Refer to the Isolation Transformer Isolation transformer failure (ANALOG BACKUP enabled) Troubleshooting Guide (DD3417357), located online at www.daktronics.com/manuals. Open CobraNet Discovery Bad digital connection and check for errors. Refer to Muffled audio from cabinet System Testing (p�17).
Page 20
-20dB. Disconnect ground at isolation transformer in the control enclosure. Refer to Humming/buzzing from audio Audio System Humming Ground loop cabinet Troubleshooting (DD3448287), located online at www.daktronics.com/manuals. For more troubleshooting steps, refer to the appropriate audio control rack manual. Troubleshooting...
Use the audio system’s Monitor Application to verify all channels of amplifiers and drivers are functioning correctly. Refer to the Sportsound Amplifier Field Guide (DD3318172), available online at www.daktronics.com/manuals, for more information. 1� With a full-range audio source (music) playing at a moderate level through the system, click the Start Monitoring button.
Page 22
If the driver checks out fine, further troubleshooting of the system is required. Note: Daktronics speaker assemblies have drivers wired in parallel. Use the following chart when measuring the DC resistance of a harness. Refer to Figure 22 for harness connector pinout.
Driver Replacement High-Frequency Driver (A-2302) Tools Required: flathead screwdriver, #2 screwdriver, 10mm wrench, utility knife, silicone 1� Remove the right-most rear access door using the flathead screwdriver. 2� Remove the internal speaker cabinet’s back panel: a� If there is a silicone seal, cut it with a utility knife. b�...
Mid-Frequency Driver (A-2305) Tools Required: flathead screwdriver, 5/32 Allen wrench, 3/16 Allen wrench, 10mm wrench, utility knife, silicone 1� Remove the center rear access door using the flathead screwdriver. 2� Remove the internal speaker cabinet’s back panel: a� If there is a silicone seal, cut it with a utility knife. b�...
Low-Frequency Driver (A-2306) Tools Required: flathead screwdriver, 5/32 Allen wrench, 3/16 Allen wrench, utility knife, silicone 1� Remove the left-most rear access door using the flathead screwdriver. 2� Remove the internal speaker cabinet’s back panel: a� If there is a silicone seal, cut it with a utility knife.
Be careful to not over-tighten the screws or the plastic hood could crack. 6� Follow the Sportsound Amplifier Field Guide (DD3318172) to verify that the correct firmware has been loaded by Daktronics Customer Service. All amplifiers present should have the firmware verified and updated to the most current version available.
Media Converters In standard audio systems, there are two media converter/network switches, one in the fiber box and one in the control enclosure, that transfer digital audio signal. Looking at the connections and LED indicators on these devices help with system troubleshooting. Figure 27: Power &...
Caution! Ensure sound cabinet is OFF during this test or damage to drivers will occur! Output a 1 kHz sine wave between 0.5 VAC–1 VAC from the mixer (go to http://dakfiles. daktronics.com/downloads/Audio/CD Test Tones/1kHz Sine Wave.wav). Measure the AC Voltage with a digital multi-meter placed between the positive and negative terminals of the male XLR connector.
24 VDC Power Supply A-2238 Industrial Media Converter / Ethernet Switch, 5 Port A-2580 Converter; Analog to Digital with CobraNet A-2898 Refer to Section 7: Daktronics Exchange and Repair & Return Programs (p�26) for information on exchanging or returning parts. Troubleshooting...
Fill out and attach the enclosed UPS shipping document. c� Ship the part to Daktronics. 3� The defective or unused parts must be returned to Daktronics within 5 weeks of initial order shipment� If any part is not returned within five (5) weeks, a non-refundable invoice will be presented to the customer for the costs of replenishing the exchange parts inventory with a new part.
Repair & Return Program For items not subject to exchange, Daktronics offers a Repair & Return Program. To send a part for repair, follow these steps: 1� Call Daktronics Customer Service� United States & Canada: 1-800-DAK-TRON (325-8766) Outside the U.S. & Canada: +1-605-275-1040 2�...
Reference Drawings Refer to Resources (p�1) for information regarding how to read the drawing number. Any contract-specific drawings take precedence over the general drawings. Reference Drawings: Harness; LF Speaker Assy; SS1500HD/SS2000HD ..........DWG-374493 Harness; MF Speaker Assy; 1500HD/2000HD ............ DWG-384426 Harness;...
Page 35
ARE CONFIDENTIAL AND PROPRIETARY. DO NOT REPRODUCE BY ANY MEANS WITHOUT THE EXPRESS WRITTEN CONSENT OF ANY MEANS WITHOUT THE EXPRESS WRITTEN CONSENT OF DAKTRONICS, INC. OR ITS WHOLLY OWNED SUBSIDIARIES. DAKTRONICS, INC. OR ITS WHOLLY OWNED SUBSIDIARIES. PIN, MATE-N-LOK, UMNL...
Page 36
ARE CONFIDENTIAL AND PROPRIETARY. DO NOT REPRODUCE BY ANY MEANS WITHOUT THE EXPRESS WRITTEN CONSENT OF PIN, MATE-N-LOK, UMNL E-1060 TYCO 350922-3 DAKTRONICS, INC. OR ITS WHOLLY OWNED SUBSIDIARIES. COPYRIGHT 2018 DAKTRONICS, INC. (USA) SPORTSOUND SYSTEMS 16 AWG, RED, PROJECT: HARNESS; MF SPEAKER ASSY; 1500HD/2000HD...
Page 37
ARE CONFIDENTIAL AND PROPRIETARY. DO NOT REPRODUCE BY ANY MEANS WITHOUT THE EXPRESS WRITTEN CONSENT OF P-1348 6 PIN MATE-N-LOK PLUG TYCO 1-480704-0 DAKTRONICS, INC. OR ITS WHOLLY OWNED SUBSIDIARIES. COPYRIGHT 2018 DAKTRONICS, INC. (USA) SPORTOUSND SYSTEMS E-1060 PIN, MATE-N-LOK, UMNL TYCO...
Page 39
3.1 DAKTRONICS SOUND CABINET IS STEEL CONSTRUCTED CABLE PROVIDED BY DAKTRONICS SKELETON WITH METAL PANELING FASTENED TO ITS EXTERIOR. INSTALLED BY DAKTRONICS 3.2 LIFT PLATES ARE PROVIDED BY DAKTRONICS. WHEN LIFTING SUBCONTRACTOR. USE 45° OR GREATER, FROM THE HORIZON, CABLE SYSTEM. 4.0 STRUCTURAL NOTES (8) REAR ACCESS DOOR FOR SERVICE 4.1 ALL STRUCTURAL STEEL SHALL BE ASTM A36, EXCEPT:...
Page 40
REQUIRMENTS. THIS DRAWING ARE CONFIDENTIAL AND PROPRIETARY. DO NOT REPRODUCE BY ANY MEANS WITHOUT THE BROOKINGS, SD 57006 EXPRESSED WRITTEN CONSENT OF DAKTRONICS, INC. 4 JUN 12 ADDED MESH PART NUMBER AND REV TO DRAWING COPYRIGHT 2011 DAKTRONICS, INC. DO NOT SCALE DRAWING...
Page 41
SERVICE 29 OCT 12 REPRODUCE BY ANY MEANS WITHOUT THE EXPRESSED FROM JB1 CHANGED DWG FROM B TO C WRITTEN CONSENT OF DAKTRONICS, INC. DATE: ADJUSTED LAYOUT AND UPDATED POWER DETAILS COPYRIGHT 2010 DAKTRONICS, INC. 20 JAN 12 ALSO ADDED FIBER SPLICE BOX...
Page 44
ARE CONFIDENTIAL AND PROPRIETARY. DO NOT REPRODUCE BY 4 FEB 15 PWS 2 ANY MEANS WITHOUT THE EXPRESS WRITTEN CONSENT OF DAKTRONICS, INC. OR ITS WHOLLY OWNED SUBSIDIARIES. A200 XP POWER COPYRIGHT 2016 DAKTRONICS, INC. (USA) FIXED WIRE COLOR LABEL ON PIN 8 OF TRX1...
Page 45
THE CONCEPTS EXPRESSED AND DETAILS SHOWN ON THIS DRAWING W-1094; 18AWG RED ARE CONFIDENTIAL AND PROPRIETARY. DO NOT REPRODUCE BY ANY MEANS WITHOUT THE EXPRESS WRITTEN CONSENT OF DAKTRONICS, INC. OR ITS WHOLLY OWNED SUBSIDIARIES. W-1092; 18AWG BLACK COPYRIGHT 2021 DAKTRONICS, INC. (USA) SPORTSOUND SYSTEMS W-1054;...
• When viewing a digital copy of this manual from www.daktronics.com/manuals, click on the appropriate manufacturer link below to view a component’s manual. If the link is broken, visit the manufacturer’s website or perform a web search for the component model number.
Daktronics Warranty & Limitation of Liability This section includes the Daktronics Warranty & Limitation of Liability statement (SL-02374)� Daktronics Warranty & Limitation of Liability...
Page 51
Warranty Coverage. Daktronics warrants to the original end user (the “End User”, which may also be the Purchaser) that the Equipment will be free from Defects (as defined below) in materials and workmanship for a period of one (1) year (the “Warranty Period”). The Warranty Period shall commence on the earlier of: (i) four weeks from the date that the Equipment leaves Daktronics’...
Page 52
In no event shall Daktronics be liable for loss, damage, or injury of any kind or nature arising out of or in connection with this Warranty in excess of the Purchase Price of the Equipment. The End User’s remedy in any dispute under this Warranty shall be ultimately limited to the Purchase Price of the Equipment to the extent the Purchase Price has been paid.
Page 53
For End User’s protection, in addition to that afforded by the warranties set forth herein, End User may purchase extended warranty services to cover the Equipment. The Extended Service Agreement, available from Daktronics, provides for electronic parts repair and/or on-site labor for an extended period from the date of expiration of this warranty. Alternatively, an Extended Service Agreement may be purchased in conjunction with this Warranty for extended additional services.