WARNING: State of California to cause cancer or birth • Correct and constant voltage must be supplied to defects or other reproductive harm. the controller to maintain proper function. 2 • FLECK 5810 & 5812 XTR2 Service Manual...
NOTE: The tank should have the distributor tube installed and have the proper amount of regenerant in place. FLECK 5810 & 5812 XTR2 Service Manual • 3...
Page 4
Hot Water Grounding Soft Water Outlet Strap Hard Water Bypass Drain Line Water Heater Brine Tank Over ow Drain (Optional) Laundry Tubs Pump Meter Softener Floor Drain Figure 2 Softened Water Flow 4 • FLECK 5810 & 5812 XTR2 Service Manual...
(up to 60) or regenerations (up to 2000) until the homeowner will need to call for service. Press when finished. Figure 4 Assistance Name Screen FLECK 5810 & 5812 XTR2 Service Manual • 5...
Page 6
Month, and Year buttons to adjust the values to the correct date. Press the button when finished to return to the Home screen. Press to return to the Home screen without saving. 6 • FLECK 5810 & 5812 XTR2 Service Manual...
Cancel Vacation Mode • Press to cancel configuration and exit to previous screen • Halts all scheduled regenerations when pressed; press without saving. again to resume normal operation. FLECK 5810 & 5812 XTR2 Service Manual • 7...
Page 8
24 hour clock. Press the Day, Month, and regeneration in meter systems. Year buttons to adjust the values to the correct date. Press the button when finished to return to the Home screen. 8 • FLECK 5810 & 5812 XTR2 Service Manual...
Page 9
Figure 15 Master Settings Warning Screen parameters will be voided. • Press to continue to the Password screen or press to return to the Home screen. FLECK 5810 & 5812 XTR2 Service Manual • 9...
Figure 19 Format Screen • relay: Contains settings for Aux 1 and Aux 2 relays. • meter: Contains settings for Meter Types. • settings review: Displays a summary of all programmed settings. 10 • FLECK 5810 & 5812 XTR2 Service Manual...
Page 11
Measures water usage and regenerates the system at the selected Regeneration Time after the calculated system capacity is depleted. The control calculates the system capacity by dividing the unit capacity by the feed water hardness and subtracting the reserve. FLECK 5810 & 5812 XTR2 Service Manual • 11...
Page 12
Relay Output screen. • Alarm Based: The relay will turn on when the specified alarm condition (or any alarm condition) is met. The relay will turn off when the alarm is cleared. 12 • FLECK 5810 & 5812 XTR2 Service Manual...
Page 13
Use the navigation arrows at the top of the screen to scroll through the parameters currently set in the control. The Settings Review screens are formatted similarly to the corresponding screen where each parameter was set. Press to return to Master Settings. FLECK 5810 & 5812 XTR2 Service Manual • 13...
Page 14
Totalizer must be reset to zero Master Settings or Home screens to view the Diagnostic to continue tracking this value. screen. Figure 28 Diagnostic Screen 14 • FLECK 5810 & 5812 XTR2 Service Manual...
Select a value in seconds that the remote switch must be closed in order to trigger the regeneration. NOTE: Some items may not be shown depending on control configuration. The control will discard any changes and exit Master Settings if any button is not pressed for five minutes. FLECK 5810 & 5812 XTR2 Service Manual • 15...
See TROUBLESHOOTING for more information about error cycle from the point where power failed. If power remains conditions. off for more than eight hours, upon power restoration the regeneration is canceled and the piston returns to service. 16 • FLECK 5810 & 5812 XTR2 Service Manual...
Reset Error The valve has reset at least five Attempt to perform a manual regeneration. If error continues, call technical times in a short amount of time. support. Probable Mechanical Failure FLECK 5810 & 5812 XTR2 Service Manual • 17...
** Includes items 24 and 25. Each valve body is installed with adapters for a 4" tank base and packaged with distributor adapter kits for 1.5" distributors (items 24 and 25). 20 • FLECK 5810 & 5812 XTR2 Service Manual...
BRINE VALVE 2. BRINE/SLOW RINSE POSITION DRAIN BRINE LINE INLET BRINE LINE INLET AIR CHECK BRINE TANK RESIN TANK 5. BRINE TANK REFILL POSITION BRINE LINE INLET 24 • FLECK 5810 & 5812 XTR2 Service Manual BRINE TANK RESIN TANK...
Page 25
4. RAPID RINSE POSITION BRINE CAM BRINE VALVE DRAIN BRINE LINE 2. BACKWASH POSITION INLET AIR CHECK BRINE TANK RESIN TANK 5. BRINE TANK REFILL POSITION BRINE LINE INLET BRINE TANK RESIN TANK FLECK 5810 & 5812 XTR2 Service Manual • 25...
Page 26
3. BACKWASH POSITION 5812 Upflow 1. SERVICE POSITION 4. RAPID RINSE POSITION DRAIN 2. BRINE/SLOW RINSE POSITION BRINE LINE INLET 5. BRINE TANK REFILL POSITION BRINE LINE INLET BRINE TANK RESIN TANK 26 • FLECK 5810 & 5812 XTR2 Service Manual...
Page 27
3. BRINE/SLOW RINSE POSITION continued 5812 Downflow 1. SERVICE POSITION BRINE LINE INLET 4. RAPID RINSE POSITION DRAIN 2. BACKWASH POSITION 5. BRINE TANK REFILL POSITION BRINE LINE INLET BRINE TANK RESIN TANK FLECK 5810 & 5812 XTR2 Service Manual • 27...
Pressing the reset switch on the circuit board while power is applied to the control will have no effect on the control or stored settings. 30 • FLECK 5810 & 5812 XTR2 Service Manual...
INJECTOR FLOW DATA TR18755 REV B FLECK 5810 & 5812 XTR2 Service Manual • 31...
Page 32
All Pentair trademarks and logos are owned by Pentair, Inc. or its affiliates. All other registered and unregistered trademarks and logos are the property of their respective owners. Because we are continuously improving our products and services, Pentair reserves the right to change specifications without prior notice.