1. Manuals
  2. Brands
  3. Smartrise Manuals
  4. DC Drives
  5. C4
  6. Startup manual

Smartrise C4 Startup Manual

Hide thumbs Also See for C4:
Table of Contents

Advertisement

Quick Links

Download this manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the C4 and is the answer not in the manual?

Questions and answers

Related Manuals for Smartrise C4

Summary of Contents for Smartrise C4

  • Page 2 Page intentionally left blank...
  • Page 3 New document format Added secondary brake wiring November 4, 2019 Added tuning steps March 5, 2020 Updated Construction procedure to include the run box must be set to ON March 5, 2020 ©2020 Smartrise Engineering, Inc. All Rights Reserved Page i...
  • Page 4 Drive Startup Manual M1000 Page intentionally left blank Page ii © 2020 Smartrise Engineering, Inc. All Rights Reserved March 5, 2020...

  • Page 5: Table Of Contents

    Closed Loop Permanent Magnet Quick Startup Guide ........... 10 Induction Motor Key Drive Parameters ..............11 Operation ......................14 No Faults ..........................14 Proper Direction ........................15 Brake Not Lifting ........................15 Appendix ....................... 16 March 5, 2020 ©2020 Smartrise Engineering, Inc. All Rights Reserved Page iii...
  • Page 6 Figure 2: Example of Parameter Table .......................... 1 Figure 3: Ground Bus Terminal ............................2 Figure 4: Example of Construction Wiring ........................5 Figure 5: Breakers ................................6 Figure 6: Terminal Locations ............................16 Page iv © 2020 Smartrise Engineering, Inc. All Rights Reserved March 5, 2020...
  • Page 7 Table 10: Parameters for A5 Motor ..........................12 Table 11: Parameters for C1 User Switches ......................... 13 Table 12: Parameters for U8 Basic..........................14 Table 13: Parameters for U9 Autotune ........................14 March 5, 2020 ©2020 Smartrise Engineering, Inc. All Rights Reserved Page v...
  • Page 8 Drive Startup Manual M1000 Page intentionally left blank Page vi © 2020 Smartrise Engineering, Inc. All Rights Reserved March 5, 2020...

  • Page 9: M1000 Drive

    Figure 1: M1000 Drive Equipment/Settings Verification Set and verify the equipment matches the job specific parameters for proper operation. See the C4 Controller sheet 01 Getting Started Parameter Table for more information. Figure 2: Example of Parameter Table March 5, 2020 ©2020 Smartrise Engineering, Inc.

  • Page 10: Grounding Requirements

    Figure 3: Ground Bus Terminal • The building, motor, transformer, and filter(s) must all share a common ground. This removes ground loops, limits impedance, and routes noise into the ground. Page 2 © 2020 Smartrise Engineering, Inc. All Rights Reserved March 5, 2020...

  • Page 11: Wiring

    A checklist must be completed during the drive wiring process. See Appendix for terminal locations. Power Perform the following to connect power. See the C4 Controller sheet 03 Machine Room for job specific information. • Connect main line power to terminal blocks L1/L2/L3.

  • Page 12: Construction

    All safety inputs are functional during Construction mode on the C4 product. When these safety devices are installed, they are connected per the C4 Controller sheet 02 Machine Room I/O of the prints, even if still on Construction mode. The following includes instructions for when none of these devices have been installed prior to beginning on Construction mode.

  • Page 13: Figure 4: Example Of Construction Wiring

    Drive Startup Manual M1000 Figure 4: Example of Construction Wiring March 5, 2020 ©2020 Smartrise Engineering, Inc. All Rights Reserved Page 5...

  • Page 14: Powering Up

    Perform the following to power up the drive. Apply external power by closing the main disconnect. Close the two-pole breaker and all pushbutton breakers. Verify the LCD on the Smartrise board and the Magnetek Drive powers up. Figure 5: Breakers Closed Loop Induction Motor Quick Start-Up Guide This quick start-up guide outlines the general parameters that must be changed/verified when a drive is installed with information that is readily available.

  • Page 15: Induction Motor Key Drive Parameters

    If the contract speed elevator is traveling too slow, increase the value. NOTE: A power cycle may be required for this to have an effect. March 5, 2020 ©2020 Smartrise Engineering, Inc. All Rights Reserved Page 7...

  • Page 16: Table 3: Parameters For A4 Power Convert

    U9 AUTOTUNE. Motor Motor rated This parameter should be set to match the Rated FLA current on the drive motor nameplate current. This parameter nameplate model Page 8 © 2020 Smartrise Engineering, Inc. All Rights Reserved March 5, 2020...

  • Page 17: Table 5: Parameters For C1 User Switches

    Control Sets the type of Closed Closed Loop Set this parameter to Method motor control Loop Vect Closed Loop Vect. Open Loop Vector technique PM ClosedLoopVct V/f Control March 5, 2020 ©2020 Smartrise Engineering, Inc. All Rights Reserved Page 9...

  • Page 18: Closed Loop Permanent Magnet Quick Startup Guide

    • Turn on DIP 6A. The M contactor automatically engages, and the screen displays TUNE command. Press the Enter Button on the drive to start the alignment. Page 10 © 2020 Smartrise Engineering, Inc. All Rights Reserved March 5, 2020...

  • Page 19: Induction Motor Key Drive Parameters

    Table 8: Parameters for A1 Drive Parameter Description Default Units Suggested Adjustments Contract Elevator contract Set to the speed the elevator will be Car Spd speed certified at. March 5, 2020 ©2020 Smartrise Engineering, Inc. All Rights Reserved Page 11...

  • Page 20: Table 9: Parameters For A4 Power Convert

    This parameter should be set to match the Voltage voltage on the drive motor nameplate voltage. This parameter nameplate model is automatically populated after a successful U9 AUTOTUNE. Page 12 © 2020 Smartrise Engineering, Inc. All Rights Reserved March 5, 2020...

  • Page 21: Table 11: Parameters For C1 User Switches

    Encoder Connect. Encoder Type of absolute EnDat EnDat Typically, this parameter Select encoder interface Sin/Cos SerialOnly should be left at default. EnDat Sin/Cos Hiperface March 5, 2020 ©2020 Smartrise Engineering, Inc. All Rights Reserved Page 13...

  • Page 22: Operation

    Make sure the car is moving without triggering a fault either on the Smartrise MR board or the drive. If the MR board is faulted, see the C4 User Manual. If the drive is faulted, see the Magnetek M1000 Manual.

  • Page 23: Proper Direction

    A and A/ encoder wires. Brake Not Lifting If the brake is not picking, make sure that the brake is wired according to C4 Controller sheet 05 Brake Connection and if there is a second brake installed, verify that the EB terminal is jumpered to the terminal.

  • Page 24: Appendix

    Drive Startup Manual M1000 Appendix The figure below shows the terminal locations. Figure 6: Terminal Locations Page 16 © 2020 Smartrise Engineering, Inc. All Rights Reserved March 5, 2020...

This manual is also suitable for:

M1000

Table of Contents