Table of Contents
Advertisement
1-13. Optional Accessories
1-13-2. Tools for Adjustment
n
The tools of Fig. No. 3 and higher that are shown in the attached table, are not used in this manual.
If they are necessary, refer to the Maintenance Manual Part 2, Volume 1.
Fig. No.
Part No.
1
3-184-527-01
2
9-919-573-01
Commercially available
The following equipment is used in the Maintenance Manual Part 2, Volume 1 only.
Fig. No.
Part No.
3
J-6001-820-A
4
J-6001-830-A
5
J-6031-840-B
6
J-6080-840-A
7
J-6086-570-A
8
J-6087-000-A
9
J-6152-450-A
10
J-6321-500-A
11
J-6322-420-A
J-6322-420-3
12
J-6323-530-A
13
J-6323-890-A
14
J-6324-030-A
15
J-6325-110-A
J-6325-380-A
16
J-6325-400-A
17
J-6325-530-A
18
J-6326-120-A
19
J-6326-530-A
20
J-6326-940-A
21
J-6329-350-A
22
J-6510-400-A
23
J-6421-440-A
24
J-7031-030-A
25
J-7031-040-A
26
J-7031-050-A
27
J-7031-260-A
28
J-7031-270-A
29
J-7031-280-A
30
J-7031-450-A
31
J-7031-460-A
32
A-8319-485-A
1-26
Description
Cleaning Cloth
Cleaning Liquid
Cleaning Tape (BCT-HD12CL)
Description
Drum Eccentricity Adjustment (3)
Drum Eccentricity Adjustment (2)
Multi Connector Cable (CIBNC)
Mirror (Small Oval Type)
Reference Flat Plate
Drum Eccentricity Adjustment (5)
Wire Clearance Check Gauge
Tape Guide Adjustment Driver
Driver (Tool) TG Adjustment (45)
Tool, 0.89 Bit (for repairing)
Stop Washer Fastening Tool
Torque Cassette (FWD back ten)
Drum Eccentricity Adjustment (7)
Torque Screwdriver Bit (For M1.4)
Torque Screwdriver Bit (For M2)
Torque Screwdriver Bit (3 kg/cm)
Drum Eccentricity Adjustment (6)
Hexagon Bit (For Torque Driver) (S:1.5)
Cassette Reference Plate
S-side Gauge
Reel Table Height Gauge (MW-935)
Extension Harness (VIDEO)
Extension Harness (AUDIO)
S-Tension Arm Positioning Tool
Weight for S-Tension Adj. (W76.7)
Weight for S-Tension Adj. (W44)
Master Block (T2)
Master Block (S2)
S-tension Adjusting Table
END Sensor Positioning Tool
Bit for Torque Driver (S:1.27)
Memory Card Box, CDS-20 Assembly
Used for
Cleaning
Used for
Adjusting the upper drum eccentricity
Adjusting the video system
Adjusting the tape path
Adjusting audio/TC head zenith
Adjusting the upper drum eccentricity
Checking the clearance
Adjusting the tape guide height
Adjusting the tape path
Installing the stop washer
Adjusting the FWD back tension
Adjusting the upper drum eccentricity
Tightening screws
Adjusting the upper drum eccentricity
Tightening screws
Adjusting the reel table height
Adjusting S4 guide height
Adjusting the reel table height
Repairing boards
Adjusting the positioning of parts
Adjusting the amount of part movement
Checking the tape guide slant
Adjusting the tension regulator
Adjusting the positioning of parts
Fastening screws
For updating software
HDW-250
Advertisement
Table of Contents
