Table of Contents
Advertisement
Quick Links
™
EiceDRIVER
enhanced 1EDI302xAS/1EDI303xAS
evaluation board
Z8F80037256
Preface
Scope and purpose
™
This document describes the EiceDRIVER
enhanced 1EDI302xAS/1EDI303xAS evaluation board. Please also
refer to the corresponding datasheet.
Intended audience
This document is intended for engineers who develop applications.
User manual
Please read the Important Notice and Warnings at the end of this document
Rev. 1.0
www.infineon.com/isolated-high-voltage-gate-driver
2020-12-18
Advertisement
Table of Contents
Related Manuals for Infineon EiceDRIVER 1EDI302 AS Series
Summary of Contents for Infineon EiceDRIVER 1EDI302 AS Series
-
Page 1: Preface
1EDI302xAS/1EDI303xAS evaluation board. Please also refer to the corresponding datasheet. Intended audience This document is intended for engineers who develop applications. User manual Please read the Important Notice and Warnings at the end of this document Rev. 1.0 www.infineon.com/isolated-high-voltage-gate-driver 2020-12-18... -
Page 2: Table Of Contents
™ EiceDRIVER enhanced 1EDI302xAS/1EDI303xAS evaluation board Z8F80037256 Table of contents Table of contents Preface .................1 Table of contents . -
Page 3: Safety Instructions
™ EiceDRIVER enhanced 1EDI302xAS/1EDI303xAS evaluation board Z8F80037256 Safety instructions Safety instructions ELECTRIC SHOCK HAZARD. Contact can cause an electric shock. If a voltage above 60 V is applied to the evaluation board, then only persons trained in working with voltages above 60 V are allowed to handle the evaluation board. In addition, ensure that hazardous live parts are not accessible and that accessible live parts are not hazardous. -
Page 4: Introduction
™ EiceDRIVER enhanced 1EDI302xAS/1EDI303xAS evaluation board Z8F80037256 Introduction Introduction General description The EiceDRIVER ™ enhanced 1EDI302xAS/1EDI303xAS evaluation board is a versatile evaluation platform for the ™ EiceDRIVER enhanced 1EDI302xAS/1EDI303xAS family. It features a half bridge configuration, see Figure There is the option to mount either the HybridPACK ™... -
Page 5: Eicedriver ™ Enhanced 1Edi302Xas/1Edi303Xas Overview
1EDI302xAS/1EDI303xAS is a high voltage IGBT/SiC driver for automotive motor drives with a power above 5 kW. The device is based on Infineon's Coreless Transformer (CT) technology, providing galvanic insulation between the low voltage domain and the high voltage domain. The device supports 400 V, 600 V and 1200 V IGBT/SiC technologies. -
Page 6: Operating Modes
™ EiceDRIVER enhanced 1EDI302xAS/1EDI303xAS evaluation board Z8F80037256 Introduction Operating modes ™ The EiceDRIVER enhanced 1EDI302xAS/1EDI303xAS product family offers different Operating modes, see Figure 2, providing intrusive diagnostic features and the ability to enter safe state" in case of system failure. For details please refer to the datasheet. -
Page 7: Block Diagram
™ EiceDRIVER enhanced 1EDI302xAS/1EDI303xAS evaluation board Z8F80037256 Introduction Block diagram Figure 3 Block diagram 1EDI3021AS and 1EDI3031AS Figure 4 Block diagram 1EDI3020AS, 1EDI3023AS, 1EDI3030AS and 1EDI3033AS User manual Rev. 1.0 2020-12-18... -
Page 8: Getting Started
™ EiceDRIVER enhanced 1EDI302xAS/1EDI303xAS evaluation board Z8F80037256 Getting started Getting started ™ The EiceDRIVER enhanced 1EDI302xAS/1EDI303xAS evaluation board is recommended to be used with the ™ ™ HybridPACK DSC or the AIMW120R045M1 CoolSIC MOSFET mounted. It can also be used in capacitive load emulation or with any other footprint compatible device. -
Page 9: Evaluation Board
™ EiceDRIVER enhanced 1EDI302xAS/1EDI303xAS evaluation board Z8F80037256 Evaluation board Evaluation board PCB overview Figure 6 shows an overview of the EiceDRIVER ™ enhanced 1EDI302xAS/1EDI303xAS evaluation board. A vertical line on the PCB marks the split between primary side and secondary side. The assembly applies for all variants of the EiceDRIVER ™... - Page 10 ™ EiceDRIVER enhanced 1EDI302xAS/1EDI303xAS evaluation board Z8F80037256 Evaluation board ™ Figure 7 AIMW120R045M1 CoolSIC MOSFET mounted with heat sink User manual Rev. 1.0 2020-12-18...
-
Page 11: Connectors
™ EiceDRIVER enhanced 1EDI302xAS/1EDI303xAS evaluation board Z8F80037256 Evaluation board Connectors ™ There are connectors on the primary side and on the secondary side of the EiceDRIVER enhanced 1EDI302xAS/ 1EDI303xAS evaluation board. The board requires a supply voltage of 15 V at the banana sockets on the primary side. -
Page 12: Led Indicators
™ EiceDRIVER enhanced 1EDI302xAS/1EDI303xAS evaluation board Z8F80037256 Evaluation board LED indicators ™ LEDs on the EiceDRIVER enhanced 1EDI302xAS/1EDI303xAS evaluation board indicate board health and driver status, see Figure Dedicated NFLT_x and RDY_x indicator for each driver Primary side supply indicator on VCC1 Secondary side VCC2 indicator for each driver If the driver pulls the NFLT_x signal to "low", then the NFLT-x LED is on to indicate a fault. -
Page 13: Operating Conditions
™ EiceDRIVER enhanced 1EDI302xAS/1EDI303xAS evaluation board Z8F80037256 Evaluation board Operating conditions To avoid electrical damage of the evaluation board, the operating range defined in Table 3 must be maintained. Table 3 Operating conditions Parameter Values Unit Note Min. Max. Banana socket Limited by secondary side UVLO, OVLO and supply absolute maximum rating of power switch... -
Page 14: Configuration
™ EiceDRIVER enhanced 1EDI302xAS/1EDI303xAS evaluation board Z8F80037256 Evaluation board Configuration ™ The EiceDRIVER enhanced 1EDI302xAS/1EDI303xAS evaluation board can be configured via jumpers on the board. The board provides the following configuration options for each driver: ENABLE_x ASC pull-up OCP disable AIP signal selection The reset button R triggers a power-on reset of both drivers and clears the Error_Mode, see Operating... -
Page 15: Jumper On Enable_X
™ EiceDRIVER enhanced 1EDI302xAS/1EDI303xAS evaluation board Z8F80037256 Evaluation board 4.5.1 Jumper on Enable_x Place the jumpers on ENABLE_B and ENABLE_T to enable each driver respectively. Figure 12 shows the location and the schematic symbol of the ENABLE_B jumper. If no jumper is placed, then an internal pull-down resistor pulls ENABLE_x to GND. -
Page 16: Jumper On Ocpx
™ EiceDRIVER enhanced 1EDI302xAS/1EDI303xAS evaluation board Z8F80037256 Evaluation board 4.5.3 Jumper on OCPx Overcurrent detection can be disabled by placing the jumper that connects OCPP to OCPN. The overcurrent ™ detection feature requires the HybridPACK DSC module to be mounted. Figure 14 OCPP_B jumper (low side driver example) User manual... -
Page 17: Aip_X Signal Selection Jumper
™ EiceDRIVER enhanced 1EDI302xAS/1EDI303xAS evaluation board Z8F80037256 Evaluation board 4.5.4 AIP_x signal selection jumper The AIP_x signal selection jumper is only relevant for the 1EDI3020AS, 1EDI3023AS, 1EDI3030AS, 1EDI3033AS variants. The jumper can be placed in two configurations. It is used to select an external circuit connected to the AIP_x pin. -
Page 18: Schematic And Layout
™ EiceDRIVER enhanced 1EDI302xAS/1EDI303xAS evaluation board Z8F80037256 Schematic and layout Schematic and layout Schematic Figure Figure 17 Figure 18 show the EiceDRIVER ™ enhanced 1EDI302xAS/1EDI303xAS evaluation board ™ schematics. The driver schematic depends on the variant of the EiceDRIVER enhanced 1EDI302xAS/1EDI303xAS evaluation board. - Page 19 ™ EiceDRIVER enhanced 1EDI302xAS/1EDI303xAS evaluation board Z8F80037256 Schematic and layout Figure 17 Driver schematic IGBT variant, 1EDI3020AS and 1EDI3021AS mounted User manual Rev. 1.0 2020-12-18...
- Page 20 ™ EiceDRIVER enhanced 1EDI302xAS/1EDI303xAS evaluation board Z8F80037256 Schematic and layout Figure 18 Primary and secondary supply schematic, all evaluation board variants User manual Rev. 1.0 2020-12-18...
-
Page 21: Layout
™ EiceDRIVER enhanced 1EDI302xAS/1EDI303xAS evaluation board Z8F80037256 Schematic and layout Layout ™ The EiceDRIVER enhanced 1EDI302xAS/1EDI303xAS evaluation board PCB consists of two layers: top and bottom. For ease of use there are no components placed on the bottom side. Figure 19 Assembly top view Figure 20 Top layer... - Page 22 ™ EiceDRIVER enhanced 1EDI302xAS/1EDI303xAS evaluation board Z8F80037256 Schematic and layout Figure 21 Bottom layer User manual Rev. 1.0 2020-12-18...
-
Page 23: Bill Of Materials
Keystone Electronics Corp. TP11, TP13, TP14, TP17, TP18, TP19, X3, X8, X9, X10, X11, X12, X13, X14, X15, X23, X24, X25, X26, X27, X28 T2, T3 BC857C ON Semiconductor BSL306N Infineon Technologies 7914G-1-000E Bourns R59, R61 NTCS0603E3202JLT Vishay R58, R60 CRCW06034K70... - Page 24 LED4, LED6 LTST-C190YKT Lite-On LED1, LED2, LED3 LTST-C190GKT Lite-On J1, J2, J3 MKDSN 1,5/ 2-5,08 Phoenix Contact TLE42644G Infineon Technologies AUIR2085S International Rectifier FID1, FID2, FID3 D11, D15 BZT52C5V6T-7 Diodes Inc. SS14-E3/61T Vishay Semiconductor D7, D9, D10, D12, D13, D14, D16...
-
Page 25: Restrictions
This evaluation board offers limited features only for evaluation and testing of Infineon products. The evaluation board is neither an end product nor a finished appliance, nor is it intended or authorized by Infineon to be integrated into end products. The evaluation board may not be used in any production system. -
Page 26: Revision History
™ EiceDRIVER enhanced 1EDI302xAS/1EDI303xAS evaluation board Z8F80037256 Revision history Revision history Revision Date Changes 2020-12-18 Document created User manual Rev. 1.0 2020-12-18... -
Page 27: Disclaimer
Infineon Technologies, All Rights Reserved. of any kind, including without limitation warranties of Infineon Technologies’ products may not be used in non-infringement of intellectual property rights of any any applications where a failure of the product or third party.