Ingersoll-Rand 150T P Series Installation And Maintenance Information
Ingersoll-Rand 150T P Series Installation And Maintenance Information

Ingersoll-Rand 150T P Series Installation And Maintenance Information

Turbine powered starter

Advertisement

Quick Links

Form P7520
04578001
Edition 3
May 2009
Turbine Powered Starter
Series 150T( )P
Installation and
Maintenance Information
Save These Instructions

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 150T P Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Ingersoll-Rand 150T P Series

  • Page 1 Form P7520 04578001 Edition 3 May 2009 Turbine Powered Starter Series 150T( )P Installation and Maintenance Information Save These Instructions...
  • Page 2 Product Safety Information Intended Use: The 150T( )P Series Air starters are intended for use in starting reciprocating internal combustion engines. These starters are designed to be operated from a remote location after proper installation on the engine requiring starting. For Additional information refer to Air Starters Product Safety Information Manual Form 45558624.
  • Page 3 3XØ (.660) Inlet [(16.76)] 3XR (.640) [(16.26)] Ø(5.530) Ø (5.750) [(140.46)] [(146.05)] 4X R (2.675) [(67.94)] 2X (60º) 2X (120°) Flange Orientation Hole (17º 30') (2.455) [(62.36)] 2X (0º 30') 3X (3.405) [(86.49)] 4X R (.605) [(15.37)] (2.022) [(51.36)] Exhaust (Dwg.
  • Page 4: Installation

    Installation Orientation of the Starter Always make certain your Air Starter is properly installed. For maximum performance, read this manual prior to the installation or It is recommended that starters be ordered in the proper orientation operation of Series 150T Turbine-Powered Starters. for your specific mounting requirements.
  • Page 5 7. Mount the Air Pressure Gauge (150BMP-1064) on or adjacent to 13. Move the starter into position, and mount it on the flywheel the control panel. It should be located where it is readily visible to housing. Tighten the mounting bolts to 100 ft-lb (136 Nm) torque. the operator.
  • Page 6: Mounting Dimensions

    Mounting Dimensions (Dwg. TP1908) 04578001_ed3...
  • Page 7 Installation (Dwg. TP909) 04578001_ed3...
  • Page 8 Installation (Continued) (Dwg. TP1910) 04578001_ed3...
  • Page 9 150T()P Turbine-Powered Starters Exploded Diagram (Dwg. TP1912) 04578001_ed3...
  • Page 10: Part Description

    150T()P Turbine-Powered Starters Parts List Item Part Description Part Number Item Part Description Part Number Cap Screw 107-25 Cover, Gear Case 150BMP-378X Washer, Lock D02-504 O-ring 150BMP-604 Inlet Cover ST500-202 O-ring 150BMP-607 Plug HSPPS-2 Seal 150BMP-271 Gasket ST500-283 Collar 10BM-30 Motor Housing ST500-40 Shaft...
  • Page 11: Maintenance Section

    Maintenance Section WARNING Always wear eye protection when operating or performing maintenance on this tool. Always turn off the air supply and disconnect the air supply hose before installing, removing or adjusting any accessory on this tool or before performing any maintenance on this tool. Note: When reading the instructions, refer to exploded diagrams in parts Information Section (page no.
  • Page 12: Cleaning The Parts

    7. Remove the Shift Ring Retainer (34) and Shift Ring Spacer (35) 2. Wash all parts except the Start Drive or any sealed bearing in from the small bore of the Piston. clean kerosene 8. Slide the Piston forward toward the drive pinion until the two Inspection of Parts halves of the Shift Ring (37) are free.
  • Page 13: Parts And Maintenance

    Assembly of the Intermediate Gear Case Assembly of Motor Housing 1. Position the assembled Drive Housing and Gear Case on a table, 1. Before installing the Motor Assembly (8), coat the O-rings on or fixture, so that the open end of the Gear Case is oriented up, the Motor Assembly and the inside of the Motor Housing bore and the pinion is down.
  • Page 14 Notes:...
  • Page 15 Notes:...
  • Page 16 www.irtools.com © 2009 Ingersoll Rand Company...

Table of Contents