Subscribe to Our Youtube Channel
Related Manuals for Ingersoll-Rand 150BMPC Series
Summary of Contents for Ingersoll-Rand 150BMPC Series
- Page 1 P6628 03532488 Edition 05 February 2014 Air Starters SERIES 150BMPC and 150BMPE Installation and Maintenance Information Save These Instructions...
-
Page 2: Installation
Either one of two lubrication systems is recommended. For typical Starter installations where the cranking cycle is less than 10 seconds, we recommend an Ingersoll-Rand No. HDL 2 Lubricator installed as shown in Dwg. TPB_688 and Dwg. TPB_389. Use either diesel or 10W non-detergent motor oil for lubricant. - Page 3 Orientation of the Air Starter 9. Using a piece of heavy duty garden hose, or some other similar large diameter hose, run it from the Relay Valve on the receiver to If the factory orientation will not fit your engine due to radial the starter location on the engine to determine the exact length location of the housing, or location of the inlet and/or exhaust of 1-1/4”...
- Page 4 Mount the HDL3 Lubricator as follows: 3. Install a 1/4” hose from the 1/8” NPT oil inlet in the side of the 1. If you are going to mount the HDL3 Lubricator on the Starter, HDL1 to the unpressurized fuel line, diesel fuel tank or separate remove one of the 3/8”...
- Page 5 Mounting Dimensions for Series 15OBMP 83LH-11 (Dwg. TPA_918-1) 03532488_ed5...
- Page 6 Mounting Dimensions for all Series (except 150BMPB83LH-11, 150BMPC81R15 and 150BMPE81R51) 3/8 PIPE TAP, LUBRICATION CONN. 1 HOLE AT 45˚ ON EACH SIDE SPECIAL WASHER 1 1/4 PIPE TAP INLET FOR 3/8 CAPSCREWS 3 9/16 2 3/8 1 1/4 R.H. ROTATION IS CLOCKWISE AND L.H.
- Page 7 Mounting Dimensions for 150LFP/150BMP - C81R15 and E81R54 (Dwg. TPA_1312-1) 03532488_ed5...
- Page 8 Pinon Data MODEL NO. Pitch Teeth Pitch View Dia. º C78RH-6, E78RH-6 2.000 18-1/32 4-7/16 3-1/4 8-11/16 12-11/32 3.624 72-1/2 º C78RH-54,E78RH-54 2.000 17-19/32 3-1/4 8-11/16 12-11/32 3.624 72-1/2 º C78RH-53, E78RH-5 2.000 17-19/32 3-1/4 8-11/16 12-11/32 3.624 72-1/2 º C78RH-5, E78RH-5 8/10 1.625...
- Page 9 Series150BMPC And150BMPE Air Starters -Exploded View Model150BMPE88 03532488_ed5...
- Page 10 SERIES 150BMPC and I50BMPE - Parts List Item Part Description Part Number Item Part Description Part Number Motor Housing Cover Assembly 150BMP-A102A Gear Case Cover Assembly (1-1/4” inlet) for E83LH-11, all 8 1 & 88 150BMP-378 Housing Cover End Plug HSPPS-3 for all others 10BM-378-1...
- Page 11 Item Part Description Part Number Item Part Description Part Number Starter Drive for C78RH-53 and E78RH-53, C78RH-54 and E78RH-54, 150BMP-A300-4 for C78RH-6, E78RH-6 101BMP-299-1 C78LH-55 and E78LH-55 C78RH-44, E78RH-44 C78RH-54 and E78RH-54 for E83LH-11 or 83RH-6 150BMP-A300-83 for C78LH-11, E78LH-11 for C88L54, C88R51, C88R53, 150BMP-A300-88 C78LH-55, E78LH-55 &...
-
Page 12: Maintenance
Maintenance WARNING Always wear eye protection when operating or performing any maintenance on this starter. Always turn off the air supply and disconnect the air supply hose before installing, removing or adjusting any accessory on this starter or before performing any maintenance on this starter. Disassembly General Instructions 4. - Page 13 4. Lubricate all open bearing and gear teeth with a liberal coat of 20. Turn the entire assembly over so that the Motor Housing Cover Ingersoll-Rand Lubricant No. 28. About 3 cc on the drive gear is is upward. sufficient. Excessive grease may rob the Starter of power during 21.
-
Page 14: Troubleshooting Guide
Assembly of the Piston 6. Apply a thin film of Ingersoll-Rand Bearing Grease No. 11 to the surface of the Drive Shaft (34). 1. Stand the Starter Drive (42), pinion end down, on the workbench. 7. Carefully take the assembled Drive Housing and install it on the... - Page 15 Notes...
- Page 16 ingersollrandproducts.com © 2014 Ingersoll Rand...
Need help?
Do you have a question about the 150BMPC Series and is the answer not in the manual?
Questions and answers