HPRT PPD3 User Manual
  1. Manuals
  2. Brands
  3. HPRT Manuals
  4. Printer
  5. PPD3
  6. User manual

HPRT PPD3 User Manual

Dot matrix printer
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Xiamen Hanin Electronic Technology Co.Ltd.
ADD:
Room 305A,Angye Building, Pioneering Park,
Torch High-tech Zone, Xiamen, China 361009
Tel.： +86-(0)592-5885993
Fax:
+86-(0)592-5885992
Web:
www.hprt.com
Dot Matrix Printer
PPD3
User Manual
（Rev.1.3）
PPD3 User Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PPD3 and is the answer not in the manual?

Questions and answers

Related Manuals for HPRT PPD3

Summary of Contents for HPRT PPD3

  • Page 1 PPD3 User Manual Dot Matrix Printer PPD3 User Manual （Rev.1.3） Xiamen Hanin Electronic Technology Co.Ltd. ADD: Room 305A,Angye Building, Pioneering Park, Torch High-tech Zone, Xiamen, China 361009 Tel.： +86-(0)592-5885993 Fax: +86-(0)592-5885992 Web: www.hprt.com...
  • Page 2 PPD3 User Manual REVISION RECORDS REV. DATE DESCRIPTION Drawn Checked Approved 2014.07.02 First edition Chen Weihua Yang Kaiqu Ren Xiaowei 2015.09.14 1.Modify packing list. Lin Yun Yang Kaiqu Ren Xiaowei 2016.03.21 1.Update the printer specification. Lin Yun Yang Kaiqu Ren Xiaowei 1.

  • Page 3: Table Of Contents

    PPD3 User Manual CONTENT STATEMENT..................................1 IMPORTANT SAFETY INSTRUCTIONS..........................2 CHAPTER 1 INTRODUCTION.............................4 1.1 Packing List..............................4 1.2 Printer Components..........................5 CHAPTER 2 SPECIFICATION..............................6 CHAPTER 3 OPERATION METHODS..........................8 3.1 Connecting the Power Cord........................8 3.2 Connecting the Cable to the Printer.......................10 3.2.1 Connecting the USB Cable....................10 3.2.2 Connecting the Cash Drawer....................10...

  • Page 4: Statement

    PPD3 User Manual STATEMENT This manual content may be altered without permission, and Xiamen Hanin Electronic Technology Co., Ltd. reserves the rights to make changes without notice in technology, spare parts, hardware and software of the products. If more information is needed about the products, please contact Xiamen Hanin Electronic Technology Co., Ltd.

  • Page 5: Important Safety Instructions

    PPD3 User Manual IMPORTANT SAFETY INSTRUCTIONS This section presents important information intended to ensure safe and effective use of this product. Read this section carefully and store it in an accessible location. 1. Safety warnings WARNINGS The print head will become very hot during printing; avoid contact with the print head after printing has ...
  • Page 6 PPD3 User Manual Handling Care Be careful not to drop paper clips, pins or other foreign matter into the unit as these cause the  printer to malfunction. Do not attempt to print when either paper or ribbon cartridge is not located in the printer, ...

  • Page 7: Chapter 1 Introduction

    PPD3 User Manual CHAPTER 1 INTRODUCTION 1.1 Packing List Note: Pls do not connect the printer to the computer before the installment finished. Open the packing of printer and keep the packing material. Make sure you own all parts as follows: Fig.1.1.1 Packing List...

  • Page 8: Printer Components

    PPD3 User Manual 1.2 Printer Components Specification of Some Part Elements Power Switch  Press “0” to turn off power and press “|” to turn on power supply; Control Panel  Features one button and three indicators to indicate printer status.

  • Page 9: Chapter 2 Specification

    PPD3 User Manual CHAPTER 2 SPECIFICATION Table 2-1 General Specifications (1/2) Items Parameter Printing Method Serial impact dot matrix Head Wire 9-pin serial configuration Printing Width 63.4mm/57mm/47.5mm Printing Printing Direction Bidirectional printing (logic seeking) Printing Speed 4.7 lps (76 mm paper width, 40 columns,1/6”) USB，Cash Drawer，Bluetooth，...
  • Page 10 PPD3 User Manual Table 2-1 General Specifications(Continued) (2/2) Items Parameter Cartridge cassette Ribbon Type RC700BR: 2 colors (Black/Red) Color RC700B: Single color (Black) Ribbon Cassettes Nylon 66 (#40 denier) Ribbon Material RC700B:Black 3,000,000 characters Ribbon Life RC700BR: Black 1,500,000/Red 750,000 characters...

  • Page 11: Chapter 3 Operation Methods

    PPD3 User Manual CHAPTER 3 OPERATION METHODS 3.1 Connecting the Power Cord Note: Before connecting/disconnecting the power cord, make sure that power to the printer and all the devices connected to the printer is turned off. Also make sure the power cable plug is disconnected from the AC outlet.
  • Page 12 PPD3 User Manual...

  • Page 13: Connecting The Cable To The Printer

    PPD3 User Manual 3.2 Connecting the Cable to the Printer 3.2.1 Connecting the USB Cable 1) Confirm the power switch is turned off. 2) As shown, insert the USB cable into the USB interface, and ensure they are matched. 3) The other end of USB interface cable should connect to the host.

  • Page 14: Connecting The Interface Cable

    PPD3 User Manual 3.2.3 Connecting the Interface Cable 1) Confirm the power switch is turned off. 2) Connect the interface cable to the connector on the rear panel of the printer. 3) Fasten the connector clasps. 4) Connect the other end of the interface cable to the host.

  • Page 15: Loading The Ribbon Cartridge

    PPD3 User Manual 3.2 Loading the Ribbon Cartridge ①Turn off power to the printer. ②Open the front cover by holding the finger grips on both ends of the cover and lifting it up. Note: Do not touch the print head immediately after printing as it can be extremely hot.
  • Page 16 PPD3 User Manual ⑤Close the front cover. Note: When removing the ribbon cartridge, raise the finger grips as shown in the figure.

  • Page 17: Loading The Paper

    PPD3 User Manual 3.3 Loading the Paper ①Open the printer cover by sliding the latch toward you. Note: Do not touch the print head immediately after printing as it can be extremely hot.  ②While observing the direction of the roll, set the paper roll into the hollow, and pull on the leading edge of the paper toward you.
  • Page 18 PPD3 User Manual Auto Cutter Model: If the printer cover is closed after turning on the power, the cutter operates automatically and the front end of the paper is cut. Note: When the paper end mark appears on the paper, replace the roll paper before it runs out.

  • Page 19: Installing The Roll Paper Guide

    PPD3 User Manual 3.4 Installing the Roll Paper Guide When using paper roll with 57.5 mm or 69.5 mm width, install the attached roll paper guide in the groove in the printer.

  • Page 20: Functions Use

    PPD3 User Manual 3.5 Functions Use 3.5.1 Power On 1) Confirm that the printer is connected to power. 2) Turn ON the power switch located on the front of the printer.The power indicator on the control panel will light up.

  • Page 21: Chapter 4 Control Panel And Other Functions

    PPD3 User Manual CHAPTER 4 CONTROL PANEL AND OTHER FUNCTIONS 4.1 Control Panel ①FEED button:Press the FEED button to feed roll paper. ②POWER indicator (Green LED):Lights when the power is ON. ③ERROR indicator (Red LED):Indicates various errors in combination with POWER indicator.

  • Page 22: Adjustment Mode

    PPD3 User Manual When the error occurs: ESC/POS Mode: Recoverable error 2) Non Recoverable Error Error POWER Lamp ERROR Lamp PAPER Lamp Buzzer Description RAM R/W error Flash Flash Flash Beep Note If a non-recoverable error occurs, turn the power OFF, wait at least 10 seconds, and turn the power back ON. If the non-recoverable error continues to be indicated, consult a dealer for repairs.

  • Page 23: Chapter 5 Preventing And Clearing Paper Jam

    PPD3 User Manual CHAPTER 5 PREVENTING AND CLEARING PAPER JAM 5.1 Preventing Paper Jam The paper should not be touched during ejection and before it is cut. Pressing or pulling the paper during ejection may cause a paper jam, paper cutting failure or line feed failure.

  • Page 24: Chapter 6 Dip Switch Setting

    PPD3 User Manual CHAPTER 6 DIP SWITCH SETTING A DIP switch is provided at the bottom of the printer, and can be set as given in the table below. Be sure to set the power switch to off before changing the settings. It is recommended to use a pointed item like a pen or flat-blade driver screw to change the settings.

  • Page 25: Serial Interface（Rs-232C

    PPD3 User Manual 6.1 Serial Interface（RS-232C） ·DIP switch 1 Switches Functions Turn on Turn off Default Line feed automatic Prohibit Turn off Handshaking XON/XOFF DTR/DSR Turn off Data length 7 bit 8 bit Turn off Odd-even verify Turn off Odd-even choice...
  • Page 26 PPD3 User Manual DIP switch 2 Switches Functions Turn on Turn off Default The mode switch in both English Chinese Turn on Chinese and English Internal control beeper Permit Prohibit Turn off Auto cutter Prohibit Permit Turn off *Off-line Busy condition...

  • Page 27: Chapter 7 Interfaces Signal

    PPD3 User Manual CHAPTER 7 INTERFACES SIGNAL Printer supports cash drawer interface and many other various communicate interfaces, such as Serial interface, parallel interface, USB interface, Ethernet interface,Wi-Fi interface. The printer has the communication board with the default USB interface and cash drawer interface, and the other communication boards with the Ethernet interface, parallel interface, RS232 interface are optional.

  • Page 28: Serial Interface

    PPD3 User Manual Note：H indicates that signal comes from Host computer, P indicates that signal comes from Printer Figure 7.1.1 7.2 Serial Interface Pin Definition PIN No. Signal Name Classic Wire Color VBUS White Green Black Figure 7.2.1 7.3 Power Supply Interface Definition 1) Pin Definition PIN No.

  • Page 29: Cash Drawer Interface Signal

    PPD3 User Manual 7.4 Cash Drawer Interface Signal 1) Electrical Characteristics Driving voltage：DC 24 V  Driving current：maximum 0.8 A ( In 510 ms)  Drawer check signal：“L” = 0～0.5 V “H” = 3～5 V  2) Cash Drawer Interface Sing RJ-11 Connector Figure 7.4.1...

  • Page 30: Serial Interface And Ethernet Interface

    PPD3 User Manual 7.5 Serial Interface and Ethernet Interface Printer serial interface are all compatible with RS-232 standard, with 25 pin (D hole type) socket. User can gain the setting of interface via printing configuration sample; the default setting of serial interface is as follow, 9600 bps (baud rates), 8 bit (data bit), 1 bit (stop bit), no parity, support RTS/CTS handshaking protocol.

Table of Contents