Speck pumpen V 30 Assembly Instructions Manual
  1. Manuals
  2. Brands
  3. Speck pumpen Manuals
  4. Water Pump
  5. V 30
  6. Assembly instructions manual

Speck pumpen V 30 Assembly Instructions Manual

Hide thumbs Also See for V 30:
Table of Contents

Advertisement

Quick Links

Assembly Instructions
V 30 – 430
Speck Pumpen Vakuumtechnik GmbH
zertifiziert: DIN EN ISO 9001

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the V 30 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Speck pumpen V 30

Summary of Contents for Speck pumpen V 30

  • Page 1 Speck Pumpen Vakuumtechnik GmbH zertifiziert: DIN EN ISO 9001 Assembly Instructions V 30 – 430...

  • Page 2: Table Of Contents

    Speck Pumpen Vakuumtechnik GmbH Assembly Instructions V 30 - 430 zertifiziert: DIN EN ISO 9001 Contents DISMANTLING PUMP..................3 Disassembling Inter Casing from Pump Casing ..............3 1.1.1 Type V 95/ V 130/ V 155 / V 330/ V 430 ................3 1.1.2...

  • Page 3: Dismantling Pump

    Speck Pumpen Vakuumtechnik GmbH Assembly Instructions V 30 - 430 zertifiziert: DIN EN ISO 9001 General Remarks Before disassembly the pump, isolate the electrical input and disconnect the operation liquid connec- tion, and inlet and outlet connections. Disassemble and reassemble the pump on a level surface. Mark all parts as they become accessible during disassembly to ensure correct positioning for reassembly.

  • Page 4: Disassembling Impeller

    Speck Pumpen Vakuumtechnik GmbH Assembly Instructions V 30 - 430 zertifiziert: DIN EN ISO 9001 Disassembling Impeller • Block the impeller (230) at shaft seal housing (441) • Remove fixed hexagon nut from impeller adjusting screw • Remove impeller (230) from shaft •...

  • Page 5: Reassembling Pump

    Speck Pumpen Vakuumtechnik GmbH Assembly Instructions V 30 - 430 zertifiziert: DIN EN ISO 9001 Reassembling Pump (e.g. V 55) CAUTION Thoroughly clean all parts before reassembly, be sure to remove all old gasket mate- rial from mounting flanges. Remove burrs from mating surfaces and mounting faces.

  • Page 6: Reassembling Shaft Seal Housing

    Speck Pumpen Vakuumtechnik GmbH Assembly Instructions V 30 - 430 zertifiziert: DIN EN ISO 9001 Reassembling Shaft Seal Housing Set motor on air ventilation cap Install distance springs (950, with molykote coated) on the impeller adjusting screw (906). Be carefull because the distance springs should be mounted as shown in the picture above.

  • Page 7: Reassembling And Adjusting Impeller

    Speck Pumpen Vakuumtechnik GmbH Assembly Instructions V 30 - 430 zertifiziert: DIN EN ISO 9001 Reassembling and Adjusting Impeller Install impeller on motor shaft Coat the disk of impeller with liquid seal (Epple) Install washer on the coated disk of impeller Thread on nut to impeller adjusting screw Adjust impeller with the impeller adjusting screw.

  • Page 8: Reassembling Pump Case And Shaft Seal Housing

    Speck Pumpen Vakuumtechnik GmbH Assembly Instructions V 30 - 430 zertifiziert: DIN EN ISO 9001 Reassembling Pump Case and Shaft Seal Housing Coat pump casing (101) with liquid seal (Epple) Install pump case (101) on inter casing (137). Thread in five hexagon head screws (901). Tighten the screws (901) cross-wise.
  • Page 9 Speck Pumpen Vakuumtechnik GmbH Assembly Instructions V 30 - 430 zertifiziert: DIN EN ISO 9001...
  • Page 10 Speck Pumpen Vakuumtechnik GmbH Assembly Instructions V 30 - 430 zertifiziert: DIN EN ISO 9001 Title: Mounting Instructions V 30 - 430 Edition: 02/03 Address Speck Pumpen Vakuumtechnik GmbH Regensburger Ring 6 D-91154 Roth Phone: (49) 09171/809-0 Fax: (49) 09171/809-10 e-mail: info@speck-pumps.de...

This manual is also suitable for:

V 95V 130V 155V 330V 430

Table of Contents

Save PDF