Operation - Makita HR2631F Instruction Manual

Bit angle (when chipping, scaling or
demolishing)
► Fig.16: 1. Action mode changing knob
The bit can be secured at the desired angle. To change
the bit angle, rotate the action mode changing knob to
the O symbol. Turn the bit to the desired angle.
► Fig.17
Rotate the action mode changing knob to the
Then make sure that the bit is securely held in place by
turning it slightly.
Depth gauge
The depth gauge is convenient for drilling holes of
uniform depth.
► Fig.18: 1. Grip base 2. Lock button 3. Depth gauge
Press the lock button on the grip base in the direction of
arrow shown in the figure and with the lock button being
pressed insert the depth gauge into the hex. hole in the
grip base.
► Fig.19: 1. Toothed side of hex hole marking on
the grip base 2. Toothed side of the depth
gauge
At this time, the depth gauge needs to be inserted so
that its toothed side is directed to the toothed side of
hex hole marking on the grip base as shown in the
figure.
► Fig.20: 1. Lock button
Adjust the depth gauge to the desired depth by moving
it back and forth while pressing the lock button. After the
adjustment, release the lock button to lock the depth
gauge.
► Fig.21: 1. Toothed side of hex hole marking on
the grip base 2. Toothed side of the depth
gauge
NOTE:
• Inserting the depth gauge with its toothed side
not directed to the toothed side of hex hole
marking on the grip base as shown in the figure
does not allow the depth gauge to be locked.
Dust cup (optional accessory)
► Fig.22: 1. Dust cup
Use the dust cup to prevent dust from falling over the
tool and on yourself when performing overhead drilling
operations. Attach the dust cup to the bit as shown in
the figure. The size of bits which the dust cup can be
attached to is as follows.
Dust cup 5
Dust cup 9
There is another type of dust cup (optional accessory)
which helps you prevent dust from falling over the tool
and on yourself when performing overhead drilling
operations.
symbol.
Bit diameter
6 mm - 14.5 mm
12 mm - 16 mm
11 ENGLISH
Installing or removing the dust cup
(optional accessory)
► Fig.23: 1. symbol 2. Grooves 3. Dust cup
Before installing the dust cup, remove the bit from the
tool if installed on the tool. Install the dust cup (optional
accessory) on the tool so that the
dust cup is aligned with the grooves in the tool.
► Fig.24: 1. Bit 2. Chuck cover
To remove the dust cup, pull the chuck cover in the
direction as shown in the figure and with the chuck
cover pulled take the bit out of the tool.
► Fig.25: 1. Attachment at the foot of dust cup
And then grab the attachment at the foot of dust cup
and take it out.
► Fig.26: 1. Bellows 2. Attachment
► Fig.27: 1. Inside periphery 2. Flat side
3. Attachment 4. Cap 5. Groove
► Fig.28: 1. Cap 2. Attachment
NOTE:
• When installing or removing the dust cup, the
cap may come off the dust cup. At that time, pro-
ceed as follows. Remove the bellows from the
attachment and fit the cap from the side shown
in the figure with its flat side facing upward
so that the groove in the cap fits in the inside
periphery of the attachment. Finally, mount the
bellows that has been removed.
► Fig.29
NOTE:
• If you connect a vacuum cleaner to your ham-
mer, cleaner operations can be performed. Dust
cap needs to be removed from the dust cup
before the connection.

OPERATION

CAUTION:
• Always use the side grip (auxiliary handle) and
firmly hold the tool by both side grip and switch
handle during operations.
Hammer drilling operation
CAUTION:
• There is a tremendous and sudden twisting
force exerted on the tool/bit at the time of hole
break-through, when the hole becomes clogged
with chips and particles, or when striking rein-
forcing rods embedded in the concrete. Always
use the side grip (auxiliary handle) and firmly
hold the tool by both side grip and switch handle
during operations. Failure to do so may result
in the loss of control of the tool and potentially
severe injury.
► Fig.30
symbol on the