Maintenance And Care - AL-KO Solo 7505 VR Instructions For Use Manual

GB

MAINTENANCE AND CARE

WARNING!
Danger of serious injury during main-
tenance and care work!
Persons can be seriously injured by mo-
ving machine parts.
Always switch the motor off and pull
the spark plug connector prior to any
maintenance and care work.
Motor may continue running. After
switching off, make sure that the mo-
tor has stopped.
Always wear work gloves when car-
rying out maintenance and care jobs
on the tiller blades.
Clean the appliance after every use.
Do not spray the machine with water! Pene-
trating water (ignition system, carburettor...)
can lead to malfunctions.
ADVICE
When the device is tilted to the side, the
carburettor must be pointing upwards.
CAUTION!
Danger of pollution due to waste oil
Waste oil that is illegally disposed of, e.g.
in the sewage system, in the ground or
in water, can cause serious pollution.
Always dispose of waste oil in ac-
cordance with legal requirements,
e.g. at waste oil acceptance points.
Every point of sale that sells oil is le-
gally bound to accept waste oil.
Never drain waste oil into the se-
wage system, the ground or into wa-
ter.
Expert inspection is required:
After running into an obstacle
If the motor stops suddenly
If there is gear damage
If the V-belt is defective
If a blade is bent
If the motor shaft is bent
Replacing the gear oil of the chain gear (18)
The gear oil of the chain gear must be replaced
every 100 working hours (amount: 0.5 l, viscosity
SAE 80). The cultivator must be warm in order to
replace the gear oil.
24
1. Remove the depth skid.
2. Unscrew the screw plug of the fill opening
(18/1).
3. Tilt the cultivator backwards into position A.
4. Suction up the waste oil with a pump.
5. Fill with new oil. Required oil amount approx.
0.5 l.
6. Measure the oil level to check the filled oil
amount: Tilt the cultivator backwards. Oil must
flow out of the fill opening just before the cul-
tivator touches the ground.
7. Screw the screw plug into the fill opening
(18/1) again.
8. Always dispose of waste oil in accordance
with legal requirements, e.g. at waste oil ac-
ceptance points.
Replacing the gear oil of the gearbox, 7505
V2R (19) (20)
The gear oil of the gearbox must be replaced
every 60 working hours (amount: 0.9 l, viscosity
SAE 80). The cultivator must be warm in order to
replace the gear oil.
Check the oil level:
1. Place the cultivator on a level surface.
2. Pull the oil dipstick (19/1) out and check that
the oil level is between "Min." and "Max.". If
the oil level is below the "Min." marking, oil
must be refilled.
3. Insert the oil dipstick again.
Draining oil:
1. Pull out the oil dipstick (20/1).
2. Place a collecting container (B) with a capa-
city of at least 1 litre under the manual trans-
mission (20/2).
3. Unscrew the oil drain plug (20/3).
4. Allow the oil to drain completely into the
collecting container (B).
5. Screw in the oil drain plug (20/3) again.
Filling in oil:
1. Fill the manual transmission with new oil
(amount: 0.9 l, viscosity SAE 80) again via the
fill opening (A) of the oil dipstick.
2. Insert the oil dipstick (20/1) again.
3. Check that the oil level is correct (see "Che-
cking the oil level").
Changing the engine oil
See operating instructions of the motor.
Maintenance and care
7505 VR / 7505 V2R