Installation - AL-KO Solo 7505 VR Instructions For Use Manual

Installation

INSTALLATION
Assembling the transport wheel (01) (02)
1. Push the wheel mount (02/1) with the trans-
port wheel into the front support point of the
frame.
2. Push the spring (02/2) and the washer (02/3)
onto the wheel mount (02/1).
3. Push the split pin (02/4) into the hole of the
wheel mount until it fits tightly.
Assembling the depth skid (01) (03)
1. Insert the depth skid (03/1) into the hole of the
frame up to the stop from below.
2. Place the washer (03/2) on the depth skid.
3. Insert the straight end of the spring split pin
(03/3) into the hole of the depth skid until the
spring split pin locks in place and cannot be
pulled out again.
Assembling the plate for the gear display and
gear lever, 7505 V2R (04)
Assembling the plate for the gear display:
1. Insert the plate (04/1) for the gear display into
the holes in the frame (04/2).
Assembling the gear lever:
2. Insert the gear lever (04/3) into the eye (A) on
the frame (04/7).
3. Attach the gear lever on the gear shaft (04/4)
using the screw (04/5) and the nut (04/6).
Mounting the upper housing cover, 7505 V2R
(05)
1. Place the housing cover (05/1) on the trans-
mission (05/2). Ensure that the hole (A) is
above the hole (B).
2. Screw the screw (05/3) into the holes.
Mounting the handlebar (06)
1. Inserting and tightening the screw (06/1): In-
sert the screw (06/1) through the eye (06/2)
in which the Bowden cable is already located.
Put on the nut (06/3) and tighten.
2. Attaching grips (06/5) for the height adjust-
ment: Place the washers (06/6) on the screws
(06/4) and lightly screw in the grips.
3. Fixing the handlebar (06/7) to the holder
(06/8): Press the cam lever (06/9) down.
Place the handlebar (06/7) on the holder
(06/8) and screw the grips tight.
To adjust the height of the handlebar, see section
"Setting the height of the handlebar".
441582_
Mount the Bowden cable for the clutch lever
(08)
The Bowden cable is already mounted on the ap-
pliance; it only needs to be connected to the clutch
lever (08/3).
1. Insert the Bowden cable (08/1) with the T-ter-
minal (08/4) into the opening (08/2) of the pre-
mounted clutch lever (08/3).
2. Insert the T-terminal (08/4) into the middle
support (08/3) of the clutch lever (08/3) and
pull the T-terminal firmly until it locks in place.
3. Insert the plastic terminal (08/5) into the sup-
port (A) and firmly press it down until it locks
in place.
For fine adjustment of the Bowden cable, see sec-
tion "Readjusting the Bowden cable of the clutch
lever".
Mounting the Bowden cable for the reverse
gear, 7505 VR (09)
The Bowden cable is already mounted on the ap-
pliance; it only needs to be connected to the lever
(09/3) for the reverse gear
1. Insert the Bowden cable (09/1) for the re-
verse gear with the cylindrical terminal into the
opening (09/2) of the lever (09/3) for the re-
verse gear.
2. Insert the cylindrical terminal (09/4) into the
middle support (A) of the lever (09/3) for the
reverse gear and pull on the cylindrical termi-
nal firmly until it locks in place.
3. Insert the controller (09/5) of the Bowden ca-
ble into the support (B) of the lever.
Mounting the gas lever (07)
1. Insert the gas lever assembly (07/1) into the
hole on the left bar of the handlebar (07/2).
2. Place the spring washer (07/3) onto the thre-
aded pin of the gas lever assembly (07/1) and
screw the nut (07/4) firmly onto the threaded
pin.
3. Check that the gas lever (07/5) can move fre-
ely.
Mount the wide tiller set, option (10) (11)
Mounting the tiller blades:
21