Atx motherboard supports 14nm lga1151 6th generation intel core i7/i5/i3, celeron and pentium processor, ddr4, dual independent display via vga and hdmi, dual intel gbe lan, usb 3.1 gen 1, sata 6gb/s, hd audio and rohs (18 pages)
Atx motherboard, intel pentium 4 processor with vga, dual sata, eight usb 2.0, sixcom, agp, five pci, two isa, gigabit ethernet and compactflash (248 pages)
Intel core 2 duo, pentium 4, pentium d or celeron d atx motherboard with 533 mhz, 800 mhz or 1066 mhz fsb and support dual-channel ddr2, vga, pcie x16, isa fdd, lpt, sata ii, usb 2.0 and pcie gbe (281 pages)
Atx lga1155 motherboard for intel core i3 quad/dual core cpu, intel c206 chipset, ddr3, vga/dvi/hdmi, dual intel pcie gbe, intel amt 7.0 support, two usb 3.0 ports, five com ports, two sata 6gb/s ports and rohs (209 pages)
Page 1
IMBA-H310 ATX Motherboard MODEL: IMBA-H310 ATX Motherboard Supports 8 Generation LGA1151 ® ® ® Intel Core™ i9/i7/i5/i3, Pentium or Celeron CPU, ® Intel H310 Chipset, DDR4, DVI-D, VGA, DP, SATA 6Gb/s, ® USB 3.2 Gen 1, Dual Intel GbE LAN, HD Audio and RoHS...
Page 2
IMBA-H310 ATX Motherboard Revision Date Version Changes September 16, 2020 1.00 Initial release Page ii...
Page 3
IMBA-H310 ATX Motherboard Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
Page 4
IMBA-H310 ATX Motherboard Manual Conventions WARNING Warnings appear where overlooked details may cause damage to the equipment or result in personal injury. Warnings should be taken seriously. CAUTION Cautionary messages should be heeded to help reduce the chance of losing data or damaging the product.
Page 11
IMBA-H310 ATX Motherboard List of Tables Table 1-1: Model Variations ......................3 Table 1-2: IMBA-H310 Specifications ................... 8 Table 2-1: Packing List ......................... 11 Table 2-2: Optional Items ......................13 Table 3-1: Peripheral Interface Connectors ................17 Table 3-2: Rear Panel Connectors ....................17 Table 3-3: +12V Power Connector Pinouts ................
Page 12
IMBA-H310 ATX Motherboard Table 3-27: TPM Connector Pinouts ................... 45 Table 3-28: USB 2.0 Connector Pinouts ..................46 Table 3-29: USB 3.2 Gen 1 Port Pinouts ..................48 Table 3-30: LAN Pinouts ......................48 Table 3-31: USB 2.0 Port Pinouts ....................49 Table 3-32: PS/2 Connector Pinouts ...................
Page 13
IMBA-H310 ATX Motherboard BIOS Menus BIOS Menu 1: Main ........................73 BIOS Menu 2: Advanced ......................74 BIOS Menu 3: CPU Configuration ....................75 BIOS Menu 4: PCH-FW Configuration ..................77 BIOS Menu 5: PTT Configuration ....................78 BIOS Menu 6: Trusted Computing ....................79 BIOS Menu 7: ACPI Configuration ....................
IMBA-H310 ATX Motherboard 1.1 Introduction Figure 1-1: IMBA-H310 ® The IMBA-H310 is an ATX motherboard. It accepts a Socket LGA1151 8 Gen. Intel ® ® Core™ i9/i7/i5/i3, Pentium or Celeron processor and supports two 288-pin 2666/2400 MHz dual-channel DDR4 DIMMs up to 64 GB.
IMBA-H310 ATX Motherboard 1.2 Model Variations The model variations of the IMBA-H310 are listed below. Packing List Packaging Type IMBA-H310 I/O shielding Standard SATA cable IMBA-H310-ECO I/O shielding Eco packaging Table 1-1: Model Variations 1.3 Features Some of the IMBA-H310 motherboard features are listed below: ATX form factor ...
IMBA-H310 ATX Motherboard 1.6 Data Flow Figure 1-4 shows the data flow between the system chipset, the CPU and other components installed on the motherboard. Figure 1-4: Data Flow Diagram Page 6...
Core™ i5-8500 up to 3.00 GHz CPU with 20 GB 2400/2133 MHz DDR4 memory) Operating -20ºC ~ 60ºC Temperature Storage Temperature -30ºC ~ 70ºC Operating Humidity 5% ~ 95% (non-condensing) Physical Specifications Dimensions 244 mm x 305 mm Weight (GW/NW) 1200 g/700 g Table 1-2: IMBA-H310 Specifications Page 8...
Only handle the edges of the PCB: Don't touch the surface of the motherboard. Hold the motherboard by the edges when handling. 2.2 Unpacking Precautions When the IMBA-H310 is unpacked, please do the following: Follow the anti-static guidelines above. Make sure the packing box is facing upwards when opening.
If any of the components listed in the checklist below are missing, do not proceed with the installation. Contact the IEI reseller or vendor the IMBA-H310 was purchased from or contact an IEI sales representative directly by sending an email to sales@ieiworld.com.
IMBA-H310 ATX Motherboard 2.4 Optional Items The following are optional components which may be separately purchased: Item and Part Number Image Dual USB cable (w bracket), 300 mm, p=2.54 (P/N: 19800-003100-100-RS) Dual RS-232 cable, 230 mm, p=2.54 (P/N: 32205-000702-100-RS) PS/2 KB/MS Y-cable with bracket, 220 mm...
IMBA-H310 ATX Motherboard 3.1.2 Peripheral Interface Connectors The table below lists all the connectors on the board. Connector Type Label 4-pin Molex power +12V power connector CPU12V1 connector Additional power connector 4-pin connector ATXPWR1 ATX power connector 24-pin connector ATX1...
IMBA-H310 ATX Motherboard 3.2 Internal Peripheral Connectors The section describes all of the connectors on the IMBA-H310. 3.2.1 +12V Power Connector CN Label: CPU12V1 CN Type: 4-pin Molex power connector, p=4.2 mm See Figure 3-2 CN Location: CN Pinouts: See Table 3-3 This connector provides power to the CPU.
IMBA-H310 ATX Motherboard 3.2.2 Additional Power Connector CN Label: ATXPWR1 CN Type: 4-pin connector, p=5.08 mm CN Location: See Figure 3-3 CN Pinouts: See Table 3-4 The additional power connector provides extra +12V and +5V power to the system. Figure 3-3: Additional Power Connector Location...
IMBA-H310 ATX Motherboard 3.2.3 ATX Power Connector CN Label: ATX1 CN Type: 24-pin connector, p=4.2 mm CN Location: See Figure 3-4 CN Pinouts: See Table 3-5 The ATX power connector connects to an ATX power supply. Figure 3-4: ATX Power Connector Location...
Dispose of used batteries according to instructions and local regulations. NOTE: It is recommended to attach the RTC battery onto the system chassis in which the IMBA-H310 is installed. CN Label: BAT1 CN Type: 2-pin wafer, p=1.25 mm...
IMBA-H310 ATX Motherboard Description RTC Battery+ Table 3-6: Battery Connector Pinouts 3.2.5 Chassis Intrusion Connector CN Label: CHASSIS1 CN Type: 2-pin header, p=2.54 mm CN Location: See Figure 3-6 CN Pinouts: See Table 3-7 The chassis intrusion connector is for a chassis intrusion detection sensor or switch that detects if a chassis component is removed or replaced.
IMBA-H310 ATX Motherboard 3.2.7 Digital I/O Connector CN Label: DIO1 CN Type: 10-pin header, p=2.00 mm CN Location: See Figure 3-8 CN Pinouts: See Table 3-8 The digital I/O connector provides programmable input and output for external devices. The digital I/O provides 4-bit output and 4-bit input.
IMBA-H310 ATX Motherboard 3.2.9 Fan Connector (CPU) CN Label: CPU_FAN1 CN Type: 4-pin wafer, p=2.54 mm CN Location: See Figure 3-10 CN Pinouts: See Table 3-10 The fan connector attaches to a CPU cooling fan. Figure 3-10: CPU Fan Connector Location...
IMBA-H310 ATX Motherboard 3.2.10 Fan Connectors (System) CN Label: SYS_FAN1, SYS_FAN2 CN Type: 3-pin wafer, p=2.54 mm CN Location: See Figure 3-11 CN Pinouts: See Table 3-11 Each fan connector attaches to a system cooling fan. Figure 3-11: System Fan Connector Locations...
IMBA-H310 ATX Motherboard 3.2.11 Front Panel Audio Connector CN Label: FRONT-PANEL1 CN Type: 10-pin header, p=2.54 mm CN Location: See Figure 3-12 CN Pinouts: See Table 3-13 This connector connects to speakers, a microphone and an audio input. Figure 3-12: Front Panel Audio Connector Location...
IMBA-H310 ATX Motherboard 3.2.12 Front Panel Connector CN Label: F_PANEL1 CN Type: 14-pin header, p=2.54 mm CN Location: See Figure 3-13 CN Pinouts: See Table 3-14 The front panel connector connects to the indicator LEDs and buttons on the computer's front panel.
IMBA-H310 ATX Motherboard 3.2.13 I C Connector CN Label: I2C1 CN Type: 4-pin wafer, p=1.25 mm CN Location: See Figure 3-14 CN Pinouts: See Table 3-15 The I C connector is used to connect I C-bus devices to the mainboard.
IMBA-H310 ATX Motherboard 3.2.15 Keyboard and Mouse Connector CN Label: KB_MS1 CN Type: 6-pin wafer, p=2.00 mm CN Location: See Figure 3-16 CN Pinouts: See Table 3-17 The keyboard and mouse connector connects to a PS/2 Y-cable that can be connected to a PS/2 keyboard and mouse.
IMBA-H310 ATX Motherboard 3.2.16 LAN LED Connectors CN Label: LED_LAN1, LED_LAN2 CN Type: 2-pin header, p=2.54 mm CN Location: See Figure 3-17 CN Pinouts: See Table 3-18 The LAN LED connectors are used to connect to the LAN LED indicators on the chassis to indicate users the link activities of the two LAN ports.
IMBA-H310 ATX Motherboard 3.2.17 Parallel Port Connector CN Label: LPT1 CN Type: 26-pin box header, p=2.54 mm CN Location: See Figure 3-18 CN Pinouts: See Table 3-19 The parallel port connector connects to a parallel port connector interface or some other parallel port device such as a printer.
IMBA-H310 ATX Motherboard 3.2.22 RS-232 Serial Port Connector CN Label: COM3, COM4, COM6 CN Type: 10-pin box header, p=2.54 mm CN Location: See Figure 3-23 CN Pinouts: See Table 3-20 Each of these connectors provides RS-232 connections. Figure 3-23: RS-232 Serial Port Connector Locations...
IMBA-H310 ATX Motherboard 3.2.23 RS-232/422/485 Serial Port Connector CN Label: COM5 CN Type: 10-pin box header, p=2.54 mm CN Location: See Figure 3-24 CN Pinouts: See Table 3-21 Each of these connectors provides RS-232, RS-422 or RS-485 communications. NOTE: The communication protocol of the serial port is set through the BIOS menu in “Advanced ...
IMBA-H310 ATX Motherboard Description Description Table 3-21: RS-232/422/485 Connector Pinouts Use an RS-232/422/485 cable to connect to a serial device. The pinouts of the DB-9 connector are listed below. RS-232 Pinouts RS-422 Pinouts RS-485 Pinouts Table 3-22: DB-9 RS-232/422/485 Pinouts...
IMBA-H310 ATX Motherboard 3.2.24 SATA 6Gb/s Drive Connector CN Label: S_ATA1, S_ATA2, S_ATA3, S_ATA4 CN Type: 7-pin SATA drive connector CN Location: See Figure 3-25 CN Pinouts: See Table 3-23 The SATA drive connectors can be connected to SATA drives and support up to 6Gb/s data transfer rate.
IMBA-H310 ATX Motherboard 3.2.29 USB 2.0 Connector CN Label: USB1 CN Type: 8-pin header, p=2.54 mm CN Location: See Figure 3-30 CN Pinouts: See Table 3-28 The USB 2.0 connector connects to USB 2.0 devices. Each pin header provides two USB 2.0 ports.
RJ-45 & USB 3.2 Gen 1 Type A combo CN Location: See Figure 3-31 CN Pinouts: See Table 3-29 and Table 3-30 There are four external USB 3.2 Gen 1 (5Gb/s) connectors on the IMBA-H310. Description Description USB_DATA- USB_DATA- USB_DATA+...
IMBA-H310 ATX Motherboard 3.3.3 Keyboard/Mouse and USB 2.0 Connectors CN Label: K/M_USB1 CN Type: PS/2 & USB 2.0 combo CN Location: See Figure 3-31 CN Pinouts: See Table 3-31 and Table 3-32 The USB 2.0 connector can be connected to a USB 2.0/1.1 device.
IMBA-H310 ATX Motherboard 3.3.4 Serial Port Connectors CN Label: COM1/1 CN Type: Dual DB-9 male CN Location: See Figure 3-31 CN Pinouts: See Table 3-33 The serial port connects to a RS-232 serial communications device. Description Description DATA SET READY...
IMBA-H310 ATX Motherboard 3.3.5 VGA and DVI-D Connectors CN Label: VIDEO1 CN Type: DB-15 female & DVI-D female combo CN Location: See Figure 3-31 CN Pinouts: See Table 3-34 and Table 3-35 The VGA connector connects to a monitor that accepts a standard VGA input.
Electrostatic discharge (ESD) can cause serious damage to electronic components, including the IMBA-H310. Dry climates are especially susceptible to ESD. It is therefore critical that whenever the IMBA-H310 or any other electrical component is handled, the following anti-static precautions are strictly adhered to.
Page 69
Turn all power to the IMBA-H310 off: When working with the IMBA-H310, make sure that it is disconnected from all power supplies and that no electricity is being fed into the system. Before and during the installation of the IMBA-H310, DO NOT: Remove any of the stickers on the PCB board.
IMBA-H310 ATX Motherboard 4.3 Socket LGA1151 CPU Installation WARNING: CPUs are expensive and sensitive components. When installing the CPU please be careful not to damage it in anyway. Make sure the CPU is installed properly and ensure the correct cooling kit is properly installed.
IMBA-H310 ATX Motherboard Figure 4-2: Remove Protective Cover Step 3: Inspect the CPU socket. Make sure there are no bent pins and make sure the socket contacts are free of foreign material. If any debris is found, remove it with compressed air.
IMBA-H310 ATX Motherboard Step 7: Insert the CPU. Gently insert the CPU into the socket. If the CPU pins are properly aligned, the CPU should slide into the CPU socket smoothly. See Figure 4-3. Figure 4-3: Insert the Socket LGA1151 CPU Step 8: Close the CPU socket.
IMBA-H310 ATX Motherboard Step 9: Connect the 12 V power to the board. Connect the 12 V power from the power supply to the board. Step 0: 4.4 Socket LGA1151 Cooling Kit Installation WARNING: DO NOT attempt to install a push-pin cooling fan.
Do not overtighten the screws. Step 5: Connect the fan cable. Connect the cooling kit fan cable to the CPU fan connector on the IMBA-H310. Carefully route the cable and avoid heat generating chips and fan blades.Step 0:...
IMBA-H310 ATX Motherboard 4.5 DIMM Installation CAUTION: For dual channel configuration, always install two identical memory modules that feature the same capacity, timings, voltage, number of ranks and the same brand. To install a DIMM, please follow the steps below and refer to Figure 4-6.
IMBA-H310 ATX Motherboard 4.6 System Configuration The system configuration should be performed before installation. 4.6.1 AT/ATX Power Mode Setting The AT and ATX power mode selection is made through the AT/ATX power mode switch which is shown in Figure 4-7.
IMBA-H310 ATX Motherboard 4.6.2 Clear CMOS To reset the BIOS, short the jumper for 3 seconds or more, then remove the jumper clip. Setting Description Open Keep current BIOS setup Short Clear BIOS Table 4-2: Clear BIOS Jumper Settings The location of the clear CMOS button (J_CMOS1) is shown in Figure 4-8.
IMBA-H310 ATX Motherboard 4.6.3 Flash Descriptor Security Override The Flash Descriptor Security Override jumper (J_FLASH1) allows to enable or disable the ME firmware update. Refer to Figure 4-9 and Table 4-3 for the jumper location and settings. Setting Description Short 1-2...
IMBA-H310 ATX Motherboard 4.6.4 USB Power Selection The USB power selection is made through the BIOS menu in “Chipset PCH-IO Configuration”. Use the USB Power SW1 and the USB Power SW2 BIOS options to configure the correspondent USB ports (see Table 4-4) and refer to Table 4-5 to select the USB power source.
This section outlines the installation of peripheral devices to the onboard connectors. 4.7.1 SATA Drive Connection The IMBA-H310 is shipped with two SATA drive cables. To connect the SATA drives to the connectors, please follow the steps below. Step 1: Locate the connectors.
IMBA-H310 ATX Motherboard Figure 4-11: SATA Power Drive Connection The SATA power cable can be bought from IEI. See Optional Items in Section 2.4. Page 67...
IMBA-H310 ATX Motherboard 4.8 Driver Installation All the drivers for the IMBA-H310 are available on IEI Resource Download Center (https://download.ieiworld.com). Type IMBA-H310 and press Enter to find all the relevant software, utilities, and documentation. Figure 4-12: IEI Resource Download Center 4.8.1 Driver Download...
Page 83
IMBA-H310 ATX Motherboard Step 3: Click the driver file name on the page and you will be prompted with the following window. You can download the entire ISO file ( ), or click the small arrow to find an individual driver and click the file name to download ( ...
IMBA-H310 ATX Motherboard 5.1 Introduction The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system settings. This chapter outlines the options that can be changed. NOTE: Some of the BIOS options may vary throughout the life cycle of the product and are subject to change without prior notice.
IMBA-H310 ATX Motherboard Function Page Up Move to the previous page Page Dn Move to the next page Main Menu – Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu -- Exit current page and return to Main Menu...
IMBA-H310 ATX Motherboard 5.2 Main The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an overview of the basic system information. Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc.
IMBA-H310 ATX Motherboard System Time [xx:xx:xx] Use the System Time option to set the system time. Manually enter the hours, minutes and seconds. 5.3 Advanced Use the Advanced menu (BIOS Menu 2) to configure the CPU and peripheral devices...
Page 89
IMBA-H310 ATX Motherboard Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Advanced CPU Configuration Offset from factory set Tcc activation Type Intel(R) Core(TM) temperature at which the i7-8700 CPU @ Thermal Control Circuit 3.20GHz must be activated. Tcc...
Page 90
IMBA-H310 ATX Motherboard C states [Disabled] Use the C states option to enable or disable the CPU C states. Disabled Disables the CPU C states. EFAULT Enabled Enables the CPU C states. Active Processor Cores [All] ...
IMBA-H310 ATX Motherboard 5.3.2 PCH-FW Configuration ® The PCH-FW Configuration menu (BIOS Menu 4) allows Intel Active Management Technology (AMT) options to be configured. Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Advanced > PTT Configuration --------------------- : Select Screen ↑...
IMBA-H310 ATX Motherboard 5.3.2.1 PTT Configuration Use the PTT Configuration menu (BIOS Menu 5) to configure settings related to the Trusted Platform Module (TPM). Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Advanced PTT Capability / State Select TPM device: PTT or dTPM.
IMBA-H310 ATX Motherboard 5.3.3 Trusted Computing Use the Trusted Computing menu (BIOS Menu 6) to configure settings related to the Trusted Computing Group (TCG) Trusted Platform Module (TPM). Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Advanced Configuration...
IMBA-H310 ATX Motherboard 5.3.4 ACPI Settings The ACPI Settings menu (BIOS Menu 7) configures the Advanced Configuration and Power Interface (ACPI) options. Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Advanced ACPI Settings ACPI Sleep State [S3 (Suspend to RAM)] ---------------------- : Select Screen...
IMBA-H310 ATX Motherboard 5.3.5 RTC Wake Settings The RTC Wake Settings menu (BIOS Menu 8) enables the system to wake at the specified time. Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Advanced Wake system with Fixed Time...
IMBA-H310 ATX Motherboard Wake up second After setting the alarm, the computer turns itself on from a suspend state when the alarm goes off. 5.3.6 F81866 Super IO Configuration Use the F81866 Super IO Configuration menu (BIOS Menu 9) to set or change the configurations for the parallel ports and serial ports.
IMBA-H310 ATX Motherboard 5.3.6.1 Serial Port 1 ~ 6 Configuration Use the Serial Port 1 ~ 6 Configuration menu (BIOS Menu 10) to configure the serial ports. Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Advanced Serial Port n Configuration...
IMBA-H310 ATX Motherboard 5.3.6.2 Parallel Port Configuration Use the Parallel Port Configuration menu (BIOS Menu 11) to configure the parallel port. Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Advanced Parallel Port Configuration Enable or Disable Parallel Port (LPT/LPTE)
IMBA-H310 ATX Motherboard 5.3.7 iWDD H/W Monitor The iWDD H/W Monitor menu (BIOS Menu 12) contains the fan configuration submenu, and displays operating temperature, fan speeds and system voltages. Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Advanced...
IMBA-H310 ATX Motherboard 5.3.7.1 Smart Fan Mode Configuration Use the Smart Fan Mode Configuration submenu (BIOS Menu 13) to configure the CPU/system fan temperature and speed settings. Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Advanced Smart Fan Mode Configuration...
IMBA-H310 ATX Motherboard Auto mode fan slope PWM Use the + or – key to change the Auto mode fan slope PWM value. Enter a decimal number between 1 and 8. 5.3.8 Serial Port Console Redirection The Serial Port Console Redirection menu (BIOS Menu 14) allows the console redirection options to be configured.
Page 102
IMBA-H310 ATX Motherboard The following options are available in the Console Redirection Settings submenu when the Console Redirection option is enabled. Terminal Type [ANSI] Use the Terminal Type option to specify the remote terminal type. VT100 The target terminal type is VT100 ...
Page 103
IMBA-H310 ATX Motherboard Even The parity bit is 0 if the number of ones in the data bits is even. The parity bit is 0 if the number of ones in the data bits is odd. Mark The parity bit is always 1.
IMBA-H310 ATX Motherboard 5.3.9 USB Configuration Use the USB Configuration menu (BIOS Menu 15) to read USB configuration information and configure the USB settings. Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Advanced USB Configuration Enables Legacy USB support.
IMBA-H310 ATX Motherboard 5.4 Chipset Use the Chipset menu (BIOS Menu 16) to access the PCH IO and System Agent (SA) configuration menus. WARNING! Setting the wrong values for the Chipset BIOS selections in the Chipset BIOS menu may cause the system to malfunction.
IMBA-H310 ATX Motherboard 5.4.1 System Agent (SA) Configuration Use the System Agent (SA) Configuration menu (BIOS Menu 17) to configure the System Agent (SA) parameters. Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Chipset > Memory Configuration Memory Configuration >...
IMBA-H310 ATX Motherboard 5.4.1.2 Graphics Configuration Use the Graphics Configuration (BIOS Menu 19) menu to configure the video device connected to the system. Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Chipset Graphics Configuration Select which of IGFX/PEG/PCI Graphics...
Page 109
IMBA-H310 ATX Motherboard DVMT Pre-Allocated [256M] Use the DVMT Pre-Allocated option to set the amount of system memory allocated to the integrated graphics processor when the system boots. The system memory allocated can then only be used as graphics memory, and is no longer available to applications or the operating system.
IMBA-H310 ATX Motherboard 5.4.1.3 PEG Port Configuration Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Chipset PEG Port Configuration Configure PEG 0:1:0 Max Speed PEG 0:1:0 Not Present Max Link Speed [Auto] ---------------------- PEG 0:1:1 Not Present : Select Screen...
IMBA-H310 ATX Motherboard 5.4.2 PCH-IO Configuration Use the PCH-IO Configuration menu (BIOS Menu 21) to configure the PCH parameters. Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Chipset PCH-IO Configuration Select the state system should be when restoring...
IMBA-H310 ATX Motherboard USB Power SW1 [+5V DUAL] Use the USB Power SW1 BIOS option to configure whether to provide power to the corresponding USB connectors (Table 5-2) when the system is in S3/S4 sleep state. This option is valid only when the above Power Saving Function (ERP) BIOS option is disabled.
IMBA-H310 ATX Motherboard 5.4.2.1 PCI Express Configuration Use the PCI Express Configuration submenu (BIOS Menu 22) to configure the PCIe Mini slot. Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Chipset PCI Express Configuration PCI Express Root Port Settings.
Page 114
IMBA-H310 ATX Motherboard PCIEX4_1 Slot [Enabled] Use the PCIEX4_1 Slot option to enable or disable the PCIe x4 slot (PCIEX4_1). Disabled Disables the PCIe x4 slot. Enabled Enables the PCIe x4 slot. EFAULT PCIe Speed [Auto] ...
IMBA-H310 ATX Motherboard 5.4.2.2 SATA Configuration Use the SATA Configuration menu (BIOS Menu 24) to change and/or set the configuration of the SATA devices installed in the system. Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Chipset SATA Configuration Determines how SATA controller(s) operate.
IMBA-H310 ATX Motherboard 5.4.2.3 HD Audio Configuration Use the HD Audio Configuration menu (BIOS Menu 25) to configure the PCH Azalia settings. Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Chipset HD Audio Subsystem Configuration Settings Control Detection of the HD-Audio device.
IMBA-H310 ATX Motherboard 5.5 Security Use the Security menu (BIOS Menu 26) to set system and user passwords. Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit Password Description Set Administrator Password If ONLY the Administrator’s password is set,...
IMBA-H310 ATX Motherboard 5.6 Boot Use the Boot menu (BIOS Menu 27) to configure system boot options. Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit Boot Configuration Select the keyboard...
Page 119
IMBA-H310 ATX Motherboard Quiet Boot [Enabled] Use the Quiet Boot BIOS option to select the screen display when the system boots. Disabled Normal POST messages displayed Enabled OEM Logo displayed instead of POST messages EFAULT Launch PXE OpROM [Disabled] ...
IMBA-H310 ATX Motherboard 5.7 Save & Exit Use the Safe & Exit menu (BIOS Menu 28) to load default BIOS values, optimal failsafe values and to save configuration changes. Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Main...
Page 122
IMBA-H310 ATX Motherboard DECLARATION OF CONFORMITY This equipment has been tested and found to comply with specifications for CE marking. If the user modifies and/or installs other devices in the equipment, the CE conformity declaration may no longer apply. FCC WARNING This equipment complies with Part 15 of the FCC Rules.
Page 124
IMBA-H310 ATX Motherboard CAUTION: Risk of explosion if battery is replaced by an incorrect type. Only certified engineers should replace the on-board battery. Dispose of used batteries according to instructions and local regulations. Outside the European Union–If you wish to dispose of used electrical and ...
Page 126
IMBA-H310 ATX Motherboard Below is a list of BIOS configuration options in the BIOS chapter. System Date [xx/xx/xx] ......................73 System Time [xx:xx:xx] ....................... 74 Tcc Activation Offset ......................75 Intel(R) SpeedStep(tm) [Enabled] ..................75 C states [Disabled] ....................... 76 Active Processor Cores [All] ....................
Page 127
IMBA-H310 ATX Motherboard Max Link Speed [Auto] ......................96 Detect Non-Compliance Device [Disabled] ............... 96 Restore AC Power Loss [Last State] ................. 97 Power Saving Function(ERP) [Disabled] ................97 USB Power SW1 [+5V DUAL] ....................98 USB Power SW2 [+5V DUAL] ....................98 PCIEX4_1 Slot [Enabled] ....................100...
Page 129
IMBA-H310 ATX Motherboard NOTE: The following discussion applies to DOS environment. Contact IEI support or visit the IEI website for specific drivers for other operating systems. The Watchdog Timer is provided to ensure that standalone systems can always recover from catastrophic conditions that cause the CPU to crash. This condition may have occurred by external EMIs or a software bug.
Page 130
IMBA-H310 ATX Motherboard NOTE: When exiting a program it is necessary to disable the Watchdog Timer, otherwise the system resets. EXAMPLE PROGRAM: ; INITIAL TIMER PERIOD COUNTER W_LOOP: AX, 6F02H ;setting the time-out value BL, 30 ;time-out value is 48 seconds ;...
IMBA-H310 ATX Motherboard E.1 PEI Beep Codes Number of Beeps Description Memory not Installed Memory was installed twice (InstallPeiMemory routine in PEI Core called twice) Recovery started DXEIPL was not found DXE Core Firmware Volume was not found Recovery failed...
IMBA-H310 ATX Motherboard F.1 RoHS II Directive (2015/863/EU) The details provided in this appendix are to ensure that the product is compliant with the RoHS II Directive (2015/863/EU). The table below acknowledges the presences of small quantities of certain substances in the product, and is applicable to RoHS II Directive (2015/863/EU).