Daiichi Electronics SMLC-110L Instruction Manual page 41

Item
Impulse withstand voltage
JIS C 1111
Noise-capacity
JEA B-402
Vibration, Shock
JIS C 1102-1
Construction
Ingress Protection code
Material
Color
Mass
Blackout guarantee
Operating temperature and
humidity limits
Storage temperature limits
6.3 Option
Item
Number of output
Output specification
Output factor
Response time
Analog output
Low input cut
Output ripple
Output adjustment
Between outputs are not insulation of minus common.
Between electric circuits (An analog output is excluded)
and case (ground).
Between analog output and case (ground).
(1) Oscillatory surge voltage
If a vibration damping waveform (1 to 1.5MHz, Peak voltage：2.5 to 3kV) is repeated
and added, there needs to be no malfunction.
Voltage input circuit (Normal/Common), Auxiliary supply circuit (Normal/Common)
(2) Square wave impulse noise
If a noise (1μs, 100ns width) is repeated and added, there needs to be no malfunction.
Auxiliary supply circuit (Common / Normal) Over 1500V
Voltage input circuit (Common / Normal) Over 1500V
Alarm output (Common) Over 1000V
Operation input (Common) Over 1000V
Analog output circuit (Induction) Over 1000V
(3) Electric wave noise
If intermittence irradiation of the electric wave of a 150MHz, 400MHz band is done by
(5W, 1m), there needs to be no malfunction.
(4) Electrostatic noise
Measurement error should be within 10％ at contact discharge 8kV and air discharge 15kV,
and malfunction shall not occur.
Vibration：Single amplitude 0.15mm, 10 to 55Hz, Each minute octave in 5 times sweep.
２
Shock：490m/s Each 3 times to the X,Y,Z direction.
Dimension：110mm(Width)×110mm(Height)×103.5mm(Depth) Body diameter：99mmφ
With terminal cover
IP40
Case，Cover：ABS(V-0) ，Terminal block：PBT ，Terminal cover：Polycarbonate
Black (Munsell N1.5)
Approx. 600g
Maximum value, Minimum value, Ground fault phase detection display, Each setting value.
Data hold by nonvolatile memory.
-10 to +55℃ , 30 to 85％ RH, Non condensing.
-25 to +70℃
4 circuits
DC4 to 20mA
DC0 to 1mA
DC0 to 5V/1 to 5V (Over 600Ω)
DC0 to 10V
One of them is designated by identical ratings.
Phase voltage (RN-SN-TN)，Line voltage (RS-ST-TR)，Frequency，
Maximum zero-phase voltage，Zero-phase voltage
A phase voltage (RN-SN-TN) constitutes only phase voltage input product.
Maximum zero-phase voltage，Zero-phase voltage, Voltage (RN-SN-TN)
：Response time setting ＋ 1 second or less.
Voltage (RS-ST-TR), Frequency
：1 second or less (Time within ±1％ of final constant value.)
An output is fixed to a lower limit if input is below a cut value.
(Function ON / OFF is possible at a setting.)
However, in the case of frequency, it excludes.
Low input cut value. Zero-phase voltage：Full scale 1.0％ or less.
Within the double precision of accuracy (％ for output span)
Bias and a span adjustment are possible according to each output individual.
Adjustable range
Specification
Specification
(Below 550Ω)
(Below 10kΩ)
(Over 2kΩ)
Voltage ：Full scale 0.5％ or less.
Bias ±10.0％ (0.1％ step) ％ for output span.
Span ±10.0％ (0.1％ step) ％ for output span.
40
SMLC-213-154
5kV 1.2/50μs
Both positive and negative
polarities, for each 3 time.