Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Harken UniPower Radial
Summary of Contents for Harken UniPower Radial
- Page 1 Installation and Maintenance Manual MRU-D Radial UniPower...
- Page 2 Index Introduction Technical characteristics Performance data Weight Maximum working load Outline UniPower Radial Winch Installation Installation procedure Positioning the self-tailing arm Motor electric wiring Electric wiring diagrams Maintenance Washing Maintenance table Winch disassembly procedure Exploded view with maintenance products Winch assembly...
-
Page 3: Technical Characteristics
® In case of doubt the Harken Tech Service is at your disposal at techservice@harken.it This Manual is available only in English. If you do not fully understand the English language, do not carry out the operations described in this Manual. -
Page 4: Installation
Maximum working load WARNING! The maximum working load (MWL) for the UniPower Radial Winch is 900 Kg (1984 lb). Subjecting the winch to loads above the maximum working load can cause the winch to fail or pull off the deck suddenly and unexpectedly during high loads causing severe injury or death. - Page 5 1. Unscrew the central screw ( 2Nm/18 in-lb) 4. Lift off the drum n°27 3. Unscrew the three screws n°25 (4Nm/35 in-lb) and remove the self-tailing arm n°8 by rotating and lifting it. UniPower Radial Installation and Maintenance Manual - Mod.D...
- Page 6 N° 5 fixing bolts M8 B. Remove the winch and drill the five 8.5 mm diameter holes and the 140 mm hole. C. Bolt the base of the winch to the deck using five socket headed M8 (not supplied by Harken ®...
- Page 7 Dual Function Control Box manual. WARNING! Before installing and using the device, read carefully the Dual Function Control Box manual available on web site www.harken.com Refer to the following chart for wire size: Total distance between winch and battery Winch Current Under 16.4 ft...
- Page 8 10 Nm (88 in-lb). NOTICE Note that correct electrical contact sequence is: Nut – Cable Terminal – Self-Locking Washer – Lock Nut UniPower Radial Installation and Maintenance Manual - Mod.D...
-
Page 9: Maintenance
Installation and maintenance of winches must be carried out exclusively by specialized personnel. ® In the case of doubt contact Harken Tech Service at techservice@harken.it WARNING! Make sure that the power is switched off before installing or carrying out maintenance on the winch. - Page 10 10. Slide out the first planetary assy n°23, remove flange n°11 . the ring gear n°4, the o-ring n°10 and the Pay attention to the o-ring n°10 in the ring gear. pinion n°2. UniPower Radial Installation and Maintenance Manual - Mod.D...
- Page 11 Use a brush to lightly lubricate all gears, gear pins, teeth and all moving parts with grease. Lightly lubricate the pawls and springs with oil. Do not use grease on the pawls! UniPower Radial Installation and Maintenance Manual - Mod.D...
- Page 12 Apply Harken grease: 1. on assy socket screw - 2. on drum gear ® NOTICE On every gear and every component that must be greased, apply Harken grease with a brush in a proper ® quantity as shown below: NOTICE...
- Page 13 In case of doubt concerning the assembly procedure contact Harken ® Tech Service: techservice@harken.it UniPower Radial Installation and Maintenance Manual - Mod.D...
-
Page 14: Ordering Spare Parts
Harken® limited worldwide warranty - Ordering spare parts ® Harken limited worldwide warranty ® ® Refer to the Harken Limited Worldwide Warranty in the Harken Catalogue and on the website www.harken.com Ordering spare parts Spare parts can be requested from Harken ®... -
Page 15: Exploded View
Exploded view 1/2 Exploded view Winch Radial UniPower 900 A, C, CW, BBB, CCC UniPower Radial Installation and Maintenance Manual - Mod.D... - Page 16 Exploded view 2/2 Winch Radial UniPower 900 A, C, CW, BBB, CCC UniPower Radial Installation and Maintenance Manual - Mod.D...
-
Page 17: Parts List
Socket head screw M6x16 UNI 5931 M0635103 S415130085 Washer Ø7.7xØ25x5.8 Pawls carrier S490960004 Screw M8x20 UNI 6109 M0614303 Gear carrier A94904100 Gear carrier S414890080 Bushing Ø9xØ11x7 *Available with service kit; see website www.harken.com **Winch product sticker UniPower Radial Installation and Maintenance Manual - Mod.D... - Page 18 Socket head screw M6x16 UNI 5931 M0635103 S415130085 Washer Ø7.7xØ25x5.8 Pawls carrier S490960004 Screw M8x20 UNI 6109 M0614303 Gear carrier A94904100 Gear carrier S414890080 Bushing Ø9xØ11x7 *Available with service kit; see website www.harken.com **Winch product sticker UniPower Radial Installation and Maintenance Manual - Mod.D...
- Page 19 Socket head screw M6x16 UNI 5931 M0635103 Screw M8x20 UNI 6109 M0614303 Pawls carrier S490960004 Gear carrier A94904100 Gear carrier S414890080 Bushing Ø9xØ11x7 *Available with service kit; see website www.harken.com **Winch product sticker UniPower Radial Installation and Maintenance Manual - Mod.D...
- Page 20 Socket head screw M6x16 UNI 5931 M0635103 Screw M8x20 UNI 6109 M0614303 Pawls carrier S490960004 Gear carrier A94904100 Gear carrier S414890080 Bushing Ø9xØ11x7 *Available with service kit; see website www.harken.com **Winch product sticker UniPower Radial Installation and Maintenance Manual - Mod.D...
- Page 21 Socket head screw M6x16 UNI 5931 M0635103 Screw M8x20 UNI 6109 M0614303 Pawls carrier S490960004 Gear carrier A94904100 Gear carrier S414890080 Bushing Ø9xØ11x7 *Available with service kit; see website www.harken.com **Winch product sticker UniPower Radial Installation and Maintenance Manual - Mod.D...