Table of Contents
Advertisement
Quick Links
FRANK GmbH ·
Hochdruckreinigungs- und Umwelttechnik ·Bochumer Straße 15 · 57234 Wilnsdorf
HOCHDRUCKREINIGER
HIGH PRESSURE CLEANER
FEM 718 MSE-Z
BETRIEBSANLEITUNG
OPERATING INSTRUCTIONS
Mode D` EMPLOI
Vor Inbetriebnahme die Betriebsanleitung und Sicherheitshinweise
lesen und beachten!
Read the instruction sheet and the safety instructions
before putting into operation and observe them!
Avant mise en route de l`appareil, lire et respecter les instructions de
Service et consignes de sécurité !
Reinigungsanlagen • Cleaning Systems
Reinigungsmaschinen • Cleaning Machines
SB-Waschplatzanlagen • Self Service Washing
Systems
Umwelttechnik • Environmental Technology
Reinigungsmittel • Cleaning Chemicals
Advertisement
Table of Contents
Related Manuals for Frank FEM 718 MSE-Z
Summary of Contents for Frank FEM 718 MSE-Z
- Page 1 Umwelttechnik • Environmental Technology Reinigungsmittel • Cleaning Chemicals FRANK GmbH · Hochdruckreinigungs- und Umwelttechnik ·Bochumer Straße 15 · 57234 Wilnsdorf HOCHDRUCKREINIGER HIGH PRESSURE CLEANER FEM 718 MSE-Z BETRIEBSANLEITUNG OPERATING INSTRUCTIONS Mode D` EMPLOI Vor Inbetriebnahme die Betriebsanleitung und Sicherheitshinweise lesen und beachten!
-
Page 2: Table Of Contents
- 1 - Contents Page Application Technical data Description Construction Function Installation Location Assembly dimensions Connecting the machine Operation Cleaning and preserving agent Nozzles and recoil forces Working pressures and spray flow rates Operating temperature Selection of the cleaning program Works setting 5.7. - Page 3 - 2 - Application The wall-mounted FRANK hot water high-pressure cleaner module is used for cleaning, degreasing, phosphatizing, preserving and desinfecting vehicles, machines, machine components, containers, etc. Technical data High-pressure stage HD: Working pressure max.: 180 bar Flow rate: 11,5 l/min Operating temperature max.:...
-
Page 4: Description
- 3 - Description Construction The wall-mounted FRANK hot water high-pressure module is a stationary, electrically-heated machine. The machine consists of an enamelled chassis with wall consoles, hot water tank made of stainless steel with electrical gilled pipes, high- pressure pump with electric motor, cold water tank and a separate master control cabinet. -
Page 5: Function
- 4 - Function 3.2.1 Functional diagram... - Page 6 - 5 - 3.2.2 Water and cleansing agent/Preserving agent system The incoming water from the mains flows past the float valve into the water inlet tank. The high-pressure pump collects the water and conveys it under pressure to the safety spray lance.
- Page 7 - 6 - 3.2.5 Level switch The tabular radiators in the hot water tank are monitored by the level switch. In case of lack of water the tabular radiators are switched off automatically. At hot water operation – programme “HOT” – the level switch protects also the high pressure pump, which is also automatically switched off in case of lack of water.
-
Page 8: Installation
- 7 - 3.2.9.1 Fuses The fuses protect the electrical components of the control circuit in the event of faults. 3.2.9.2 Motor protection The motor is protected against overloading by an overload release device. In the event of overloading the release device switches off the motor and restarts it again automatically after it has cooled down. -
Page 9: Assembly Dimensions
- 8 - Assembly dimensions... -
Page 10: Connecting The Machine
The long-distance piping is to be carried out by a skilled fitter for oil and water systems. Only components of the FRANK long-distance piping range are to be used as the thermal and chemical constancy can be guaranteed for these parts only. -
Page 11: Operation
- 10 - Operation Cleaning agents Only the following FRANK chemicals and possibly certain other additional agents authhorized by the manufacturer may be used, since material compatibility can only be guaranteed for these cleaning agents. FRANK Cleaning agents FRANKOCLEAN NER 0800... -
Page 12: Working Pressures And Spray Flow Rates
- 11 - Working pressures and spray flow rates, infinitely variable Working pressure Flow rate l/min 11,5 10,5 Operating temperatures The operating temperature can be adjusted infinitely on the thermostat. It can be set to maximum 70 °C. 5..5 Selection of the cleaning program ... -
Page 13: Works Setting
- 12 - Works setting The machine has been set and tested according to the technical data under section 2. The works setting and testing has been done under the following conditions: Ambient temperature (Air temperature): 18 °C Medium air pressure: 986 hPa Commissioning 5.7.1 Initial commissioning... - Page 14 - 13 - Formulation concentration 1:10 (1 part cleaning agent, 10 parts water) Dosing valve position Percentage of final concentration of the cleaning agent in the water jet 0,09 0,39 0,51 0,52 0,55 0,58 0,63 0,66 0,67 If higher concentrations are required, the formulation of the cleaning agent has to be increased.
-
Page 15: Taking The Machine Out Of Order
- 14 - 5.7.4 Operating the safety spray lance Direct high-pressure safety spray lance at the object to be cleaned. Release and actuate safety lever on the spray gun. The water is now conveyed to the nozzle. Spray pressure builds up and quickly attains the selected operating pressure. Avoid an opening and closing of the spray gun in quick succession. -
Page 16: Restarting Of The Machine
- 15 - 5.9. Restarting of the machine When restarting the machine, make sure the machine and particularly the power supply cord, the high-pressure hose and the safety spray lance are in perfectly good condition. Maintenance Maintenance and repair works may only be done by qualified personnel. -
Page 17: Troubles, Causes And Troubleshooting
- 16 - Troubles, causes and troubleshooting Trouble Possible cause What to do about it Machine is not No current; low voltage Have an expert: running or switches Interruptance in power supply check the fuse of local off during operation installation and control fuses in the circuit box of the machine, replace if necessary;... - Page 18 - 17 - Trouble Possible Cause What to do about it Pump fails to reach the Defective pump sleeves Have sleeves replaced required pressure Defective pump valves Have valves replaced Worn out spray nozzle Have nozzle replaced Wrong spray nozzle Mount correct nozzle Water filter contaminated Have filter cleaned...
-
Page 19: Checking
- 18 - Checking The machine must be checked by an expert in accordance with the " regulations for liquid spray appliances" if necessary, but at least every 12 months in order to guarantee a safe operation. The results of these tests must be recorded in writing. Prevention of accidents The machine has been designed as to exclude accidents if operated properly. - Page 20 - 19 - OPERATING INSTRUCTIONS FEM 813 - 18 kW Supplements, corrections Technical Data Maximum volume flow: 13 l/min Operating pressure: 130 bar Operating temperature: 70 °C Heat capacity: 18 kW Water temperature 70 °C after heating period: 13 min. (approx.) Constant temperature: 35 °C (approx.) Mains supply:...
- Page 21 - 20 - OPERATING INSTRUCTIONS FEM 813 - 30 kW Supplements, corrections Technical Data Maximum volume flow: 13 l/min Operating pressure: 130 bar Operating temperature: 70 °C Heat capacity: 30 kW Water temperature 70 °C after heating period: 8 min. (approx.) Constant temperature: 48 °C (approx.) Mains supply:...