Related Manuals for Charder P510
Summary of Contents for Charder P510
- Page 1 Price Computing Scale P510 User Manual www.charder.com Please read this manual carefully before operating your device and retain it for future reference. CD-IN-XXXXX REV001 2020/04...
-
Page 2: Table Of Contents
P510 Series Table of Contents I. INTRODUCTION ......................2 Safety Precautions ..............................2 Level Adjustment ..............................2 II. INSTALLATION ......................2 Package Contents ..............................2 Selecting the Location ............................... 3 Display & Keypad Description ........................... 3 Operation .................................. 4 Power On ................................4 Weight Measurement ............................ -
Page 3: Introduction
P510 Series I. INTRODUCTION This manual provides detailed instructions for the installation and operation of the P510 Price Computing Scale. Please read this manual in its entirety before installing and operating the device. Safety Precautions • Do not allow liquids or foreign devices to enter device. -
Page 4: Selecting The Location
P510 Series Selecting the Location Place the device in an environment free from excessive dust and moisture. Place the device on a stable, vibration-free, level surface away from direct sunlight. If the AC adapter is used, ensure that power cable is routed to minimize tripping hazard. -
Page 5: Operation
P510 Series : Price Look Up for PLU 15-99 : Program Price Look Up for PLU 1-99 : Price Look up for PLU 1-14 : Numeric keys 0-9 Operation Power On The power switch is located on the bottom right-side panel towards the front of the device. After device is switched on, it will perform a brief display test. -
Page 6: Standard Unit Price Computation
P510 Series Standard Unit Price Computation 1. Place item on device. 2. Enter UNIT PRICE using keypad. 3. Read WEIGHT and TOTAL PRICE. 4. If label printer is connected to device, press PRINT key to print a label. 5. Remove item from measurement platform. Weight will return to zero, and price will be cleared. - Page 7 P510 Series Pre-Pack Operation with PLU Used for repetitive price-computing of items with the same unit price. 1. Select the desired PLU as above. 2. Press the PRE-PACK key. The PRE-PACK symbol will be marked on the display. 3. Place item on scale.
-
Page 8: Settings
P510 Series III. SETTINGS To access settings, press and hold the PRE-PACK key while switching the device on. Screen will display "SETUP". Use the following keys to navigate the settings: PRE-PACK ↓ Accept displayed setting, proceed to next step TARE → Toggles available settings for the current step ZERO ↑... -
Page 9: Care & Cleaning
P510 Series Setting Details Beep When turned on, device will emit "beeping" noise when keys are pressed. Press TARE to toggle between on/off, and press PRE-PACK to confirm setting. Sleep When turned on, device will enter sleep mode after a certain period of time. Press TARE to toggle between 30/60 seconds, and press PRE-PACK to confirm setting. -
Page 10: Error And Status Messages
P510 Series V. ERROR AND STATUS MESSAGES ERROR MESSAGE DESCRIPTION REMEDY Maximum capacity exceeded Remove excess weight, and use device within capacity limits. Low battery Recharge batteries and/or connect device to AC adapter Program error Contact distributor for service Zero value too high Empty measurement pan. -
Page 11: Warranty
P510 Series VI. WARRANTY If Charder is responsible for a fault or defect present upon receipt of the unit, Charder shall either repair the fault, ․ or supply a replacement unit. Should the repairs or replacement delivery fail, statutory provisions shall be valid. - Page 12 P510 Series Charder Electronic Co., Ltd. No.103, Guozhong Rd., Dali Dist., Taichung City 41262 Taiwan (R.O.C.) Tel: +886-4-2406 3766 Fax: +886-4-2406 5612 http://www.charder.com CD-IN-XXXXX REV001 2020/04...
Need help?
Do you have a question about the P510 and is the answer not in the manual?
Questions and answers