Specifications - Makita DFL062F Instruction Manual

ENGLISH (Original instructions)

SPECIFICATIONS

Model:
Fastening torque
Square drive
No load speed
Rated voltage
Overall length
(Depending on the battery)
Net weight
• Due to our continuing program of research and development, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge
Charger
• Some of the battery cartridges and chargers listed above may not be available depending on your region of
residence.
WARNING:
Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
and chargers may cause injury and/or fire.
Intended use
The tool is intended for screw driving in wood, metal
and plastic.
Noise
The typical A-weighted noise level determined accord-
ing to EN62841-2-2:
Model DFL062F
Sound pressure level (L
Uncertainty (K) : 3 dB(A)
Model DFL124F
Sound pressure level (L
Uncertainty (K) : 3 dB(A)
Model DFL203F
Sound pressure level (L
Uncertainty (K) : 3 dB(A)
The noise level under working may exceed 80 dB (A).
NOTE: The declared noise emission value(s) has
been measured in accordance with a standard test
method and may be used for comparing one tool with
another.
NOTE: The declared noise emission value(s)
may also be used in a preliminary assessment of
exposure.
Hard joint
Soft joint
) : 70 dB(A) or less
pA
) : 70 dB(A) or less
pA
) : 70 dB(A) or less
pA
DFL062F
1.5 - 6 N•m
1.5 - 6 N•m
-1
470 min
1.6 - 1.9 kg
BL1415N / BL1415NA / BL1430 / BL1430B / BL1440 / BL1450 /
BL1460A / BL1460B
DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared
value(s) depending on the ways in which the tool is
used especially what kind of workpiece is processed.
WARNING:
Be sure to identify safety measures
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (tak-
ing account of all parts of the operating cycle such
as the times when the tool is switched off and when
it is running idle in addition to the trigger time).
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841-2-2:
Model DFL062F
Work mode: screwdriving without impact
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Model DFL124F
Work mode: screwdriving without impact
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Model DFL203F
Work mode: screwdriving without impact
Vibration emission (a
Uncertainty (K) : 1.5 m/s
4 ENGLISH
DFL124F DFL203F
5 - 12 N•m 8 - 20 N•m
5 - 12 N•m 8 - 20 N•m
9.5 mm
-1
410 min 220 min
D.C. 14.4 V
432 - 449 mm
1.7 - 1.9 kg
2
) : 2.5 m/s or less
h
2
2
) : 2.5 m/s or less
h
2
2
) : 2.5 m/s or less
h
2
-1