Related Manuals for Safety Vision OBSERVER 4401-HVR
Summary of Contents for Safety Vision OBSERVER 4401-HVR
- Page 1 OBSERVER™ 4401-HVR HARDWARE USER GUIDE For system configuration, please refer to the Observer Series Configuration Guide.
- Page 2 Safety Vision reserves the right to amend the information in this document at any time without prior notice. This material is confidential and the property of Safety Vision. It is shared with your company for the sole purpose of helping you with the operation of the described equipment.
-
Page 3: Table Of Contents
OBSERVER 4401-HVR HARDWARE USER GUIDE CONTENTS Components Front Panel Rear Panel Wiring Diagram Installation Security Cover Flat Mount Removing / Inserting the SD Card Appendix A: Specifications Appendix B: Power Consumption Charts Appendix C: Dimensions FCC Compliance Statement... - Page 4 OBSERVER 4401-HVR HARDWARE USER GUIDE The Observer Series Recorders consists of two (2) separate user guides: 1. Hardware User Guide 2. Configuration User Guide This document is the Hardware User Guide. It provides wiring, installation, and components description. For system configuration, please refer to the Observer Series Configuration Guide.
-
Page 5: Front Panel
OBSERVER 4401-HVR HARDWARE USER GUIDE Components Front Panel IR Remote Sensor The IR Remote Sensor receives signals from the HVR Remote Control. Status LEDs The Status LEDs illuminate to display the current status of the HVR (see chart below). USB Port... -
Page 6: Rear Panel
OBSERVER 4401-HVR HARDWARE USER GUIDE Rear Panel WiFi Antenna Connector (SMA) Connection to an Power Port Connection for the 41-PWRHRNS main external antenna for the internal WiFi module. power harness. GPS Antenna Port Connection an external GPS AHD IN Port Connection for analog high definiton antenna. -
Page 7: Wiring Diagram
OBSERVER 4401-HVR HARDWARE USER GUIDE Wiring Diagram... -
Page 8: Installation
OBSERVER 4401-HVR HARDWARE USER GUIDE Installation Security Cover After connecting all needed cables to the rear of the HVR as shown in the wiring diagram (see page 5), snap the security cover into place and secure it using the included security Torx screw. -
Page 9: Flat Mount
OBSERVER 4401-HVR HARDWARE USER GUIDE Flat Mount Secure the HVR to the surface with four (4) #10 machine screws with nyloc nuts, self-tapping screws, or rivets. Ensure that the front panel of the NVR remains accessible and there is a minimum 2.5 inches of clearance for cables. -
Page 10: Removing / Inserting The Sd Card
NOTE: Ensure the SD card’s write protection slider is in the “unlocked” position. NOTE: Use only SD cards obtained from Safety Vision. Insert an SD card into the SD card slot label-side up, with the notch to the right, until it clicks in place. -
Page 11: Appendix A: Specifications
OBSERVER 4401-HVR HARDWARE USER GUIDE Appendix A: Specifications PART NUMBER POST-EVENT RECORDING 4401-HVR Configurable up to 30 minutes OS SUPPORT ETHERNET Linux 4.9 6-pin M12 (1 × 10/100M) CAMERA CHANNELS WI-FI (ANTENNA REQUIRED) 4 channels (AHD) + 1 IP Embedded module (802.11 b/g/n/ac) -
Page 12: Appendix C: Dimensions
OBSERVER 4401-HVR HARDWARE USER GUIDE Appendix C: Dimensions... -
Page 13: Fcc Compliance Statement
OBSERVER 4401-HVR HARDWARE USER GUIDE FCC Compliance Statement This device has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. - Page 14 CORPORATE HEADQUARTERS 6100 W. Sam Houston Pkwy. N. Houston, TX 77041-5113 Main: 713.896.6600 Toll Free: 800.880.8855 Fax: 713.896.6640 www.safetyvision.com Copyright © 2021 Safety Vision, LLC All Rights Reserved.