Related Manuals for BDI CORRIDOR BAR 5620
Summary of Contents for BDI CORRIDOR BAR 5620
- Page 1 CORRIDOR® BAR 5620 BAR CABINET INSTRUCTION MANUAL LET’S GET STARTED. DESIGN MATTHEW WEATHERLY...
- Page 2 Congratulations on the purchase of your Corridor Bar 5620 from BDI. Your cabinet has been designed to provide a lifetime of enjoyment. This manual will provide you with assembly instructions and other helpful information that will ensure that you get the most out of your cabinet.
- Page 3 Unpack and identify the parts listed below. Note that some components are shipped inside the cabinet. The assembly workspace should be a non-marring surface such as carpet. For missing hardware pieces, please contact BDI Customer Service at customerservice@bdiusa.com. Do not use power tools for assembly of this product.
- Page 4 HARDWARE AND COMPONENTS HARDWARE AND COMPONENTS PART # PART # C1 (right) & C2 (left) DESCRIPTION DESCRIPTION Cabinet Metal Leg QUANTITY QUANTITY 1 of each PART # PART # DESCRIPTION Crossbar DESCRIPTION Glass Top QUANTITY QUANTITY 4 | BDIUSA.COM CORRIDOR 5620...
- Page 5 STEP 1. BUILD THE BASE ASSEMBLY Slide tab of (C1 & C2) Metal Legs into PART/DESCRIPTION (C3) Crossbar and attach with 4 (H1) Screws and tighten with (T2) Hex Wrench. T2-HEX WRENCH H1-SCREW...
-
Page 6: Step 2. Attach The Base
ASSEMBLY STEP 2. ATTACH THE BASE Using 8 (H1) Screws and 1 (H2) Screw, attach base PART/DESCRIPTION assembly to (A) Cabinet with (T2) Hex Wrench. Start all screws before fully tightening all screws. T2-HEX WRENCH H1-SCREW H2-SCREW 6 | BDIUSA.COM CORRIDOR 5620... - Page 7 2 PERSON TASK STEP 3. INSTALL DOOR PULLS AND RUBBER BUMPER ASSEMBLY With help from another person, carefully position PART/DESCRIPTION (A) Cabinet upright and install (H) Door Pulls using (I) Screw and (T1) Phillips Screwdriver. Adhere T1-PHILLIPS (J) Rubber Bumper to center of the top of SCREWDRIVER (D) Cabinet.
- Page 8 ASSEMBLY STEP 4. PLACE GLASS TOP Attach (C4) Glass Top to (A) Cabinet using PART/DESCRIPTION (H4) Screws (Silver) and (T2) Hex Wrench. Do not overtighten. T2-HEX WRENCH H4-SCREW (SILVER) 8 | BDIUSA.COM CORRIDOR 5620...
-
Page 9: Adjustable Shelf
STEP 4. INSTALL BACK PANELS FINE TUNING ASSEMBLY ADJUSTABLE SHELF PART/DESCRIPTION The shelf pins located inside the right compartment may be repositioned using (T1) Phillips T1-PHILLIPS Screwdriver, allowing you to raise or lower the SCREWDRIVER Adjustable Shelf to the desired level. T3-OPEN MOUTH LEVEL CABINET WRENCH... -
Page 10: Care And Maintenance
While BDI’s stained wood finishes are stable in tone & appearance, all finishes are subject to some degree of discoloration with prolonged exposure to direct sunlight. Please take care to avoid positioning your BDI cabinet in any area with extensive direct sunlight. -
Page 11: Warranty
WARRANTY BDI warrants to the original purchaser that for the below stated warranty term, BDI will repair or replace any product, part, or component covered by this warranty which fails under normal use as a result of a defect in material or workmanship. BDI will repair or replace the aforementioned product, part or component with a comparable product, part or component. - Page 12 These distinctive product configurations are protected by US and international patents, trade dress, and/or copyright laws. Corridor & BDI are trademarks of Becker Designed, Inc. All rights reserved. ©2020, BDI | V.08.24.2020 Made in China.