Polaris Mazda BT-50 RW-50/15 Installation Instructions Manual

Hide thumbs Also See for Mazda BT-50 RW-50/15:

Advertisement

Quick Links

Thank you for purchasing the Polaris Mazda BT50 RW-50/15 in-dash unit.
Before removal and installation, be sure to thoroughly read these instructions.
Keep these instructions with your vehicle records for future reference.
This installation guide is for reference only. Polaris takes no responsibility for any
damage caused to any vehicle through incorrect installation, unsafe practices or poor
workmanship.
Warranty for this product is 1 year from date of purchase, however warranty will be
void if:
• The unit is tampered with, damaged or modified in anyway.
• Reverse camera cable is cut or modified in any way
• Reverse camera is subjected to over voltage
• The Navigation SD card is damaged or tampered with in any way (this includes in-
stalling foreign mapping or software onto the SD card)
The Mazda BT50 RW-50/15 is covered for 1 year and includes:
• Defective Equipment
• Defective Cables
Not Covered under warranty:
• Abuse
• Improper installation
• Alteration to cables (this includes cutting of any cables)
• Accidents
This Polaris BT50 RW-50/15 utilises the OEM CD player, AM/FM Radio and USB input.
If you have any specification or troubleshooting enquiries in regards to these func-
tions please refer to your owner's manual.
If you have any questions concerning the installation, warranty or the operation of
the unit, please contact
We hope that you enjoy the Polaris BT50 RW-50/15 in dash unit.
Mazda BT-50 RW-50/15
installation instructions
Version 3
Warranty Terms
Polaris
1300 555 514.
on
1

Advertisement

Table of Contents
loading

Summary of Contents for Polaris Mazda BT-50 RW-50/15

  • Page 1 • Alteration to cables (this includes cutting of any cables) • Accidents This Polaris BT50 RW-50/15 utilises the OEM CD player, AM/FM Radio and USB input. If you have any specification or troubleshooting enquiries in regards to these func- tions please refer to your owner’s manual.
  • Page 2: Wiring Diagram

    QUICK REFERENCE GUIDE When the manual refers to ‘TOP SECTION’ this is the area located where the OEM 3.5” screen was originally mounted When the manual refers to ‘OEM CD HOUSING AREA’ this is the area located where the OEM CD was originally mounted When the manual refers to ‘OEM’, this means original equipment manufacturer.
  • Page 3 Prior to installing the unit, please make sure that you have all the parts from the box and the necessary tools to complete the installation. Parts - Packing List 1. RW-50/15 Fascia 2. RW-50/15 8” Interface Screen 3. Wiring Harness 4.
  • Page 4 Important Installation tips • We no longer recommend mounting the GPS Antenna underneath the dashboard; please mount it on top of the dash in the right /left top corner near the windscreen. • Prior to installation, please disconnect and turn off the OEM Bluetooth function.
  • Page 5 Step 1 - Remove Air conditioning panel 2. Unplug harness and set 1. Starting from the bottom, use trim air conditioning controls aside tools to remove air conditioning controls Step 2 - Remove Fascia Panel 2. Gently pull fascia panel 3.
  • Page 6 Step 4 - Prepare all the cabling in preparation for the head unit to be installed. A. External Bluetooth Microphone 3. Use lever to drop steering 2. Mount microphone in the 1.Remove door rubber and wheel column down top right hand corner of the the driver’s pillar trim windscreen 4.
  • Page 7: External Antenna

    13. Plug harness back into 14. Reinstall trim. 12. Connect plug into OEM instrument cluster panel and NOTE: please make sure the plug located in the remount. bottom section of the trim TOP SECTION and connect plug goes underneath the two into the OEM plug located in reset dials.
  • Page 8: Rear Camera

    E. Rear Camera 1. Run your long strike through chassis rail from front to rear. 4. Attach the number plate camera 2. Tape camera cable (large 4 pin din) onto strike at the rear of the vehicle. onto number plate (as shown above) 3.
  • Page 9 F. Wiring Diagram Connects to OEM CD player Connects to OEM Radio Plugs into OEM Screen plug Connects to Connects to back of the back of the RW50/15 RW50/15 screen screen Connects to back of the RW50/15 screen Connects to OEM CD player harness Connects to OEM Radio plug Step 5 - Mount OEM CD player 3.
  • Page 10 Step 6 - Prepare the BT50 RW-50/15 OEM fascia 2. Remove the 10 screws holding the button panel and air conditioning vents in place - set aside. 1. Grab the OEM fascia and remove all 9 clips and set aside. 3.
  • Page 11: Step 7 - Fascia Installation

    Step 7 - Fascia installation 2. Plug the OEM button panel 1. Connect PLUG A & B and the 3. Make sure all the cables are harness into the back of the GPS Antenna into the back of tucked away neatly before se- OEM button panel the RW50/15 screen curing into place.
  • Page 12: Steering Wheel Controls

    Please note: The voice recognition steering wheel control will now bring up the Bluetooth feature. Or you can watch a video on how to setup the steering wheel controls, go to www.youtube.com.au and type in ‘Polaris BT50 steering wheel control setup’...

Table of Contents