Advertisement
Quick Links
For Intermediate & Advanced Fliers.
SAFETY PRECAUTIONS
This radio control model is not a toy!
Fist-time builders should seek advice from people having building
Experience in order to assemble the model correctly and to produce
Its performance to full extent.
Assemble this kit only in places out of children's reach!
Take enough safety precautions prior to operating this model.
You are responsible for this model's assembly and safe operation!
Always keep this instruction manual ready at hand for quick
reference, even after completing the assembly.
Notice:
**This manual included Specification, Parts list in paper and CD full instruction manual.**
Before you read the CD. Please install Acrobat Reader. First.
"Acrobat Reader" logo are trademarks of Adobe Systems Incorporated
Advertisement
Related Manuals for H-KING Pacer G007
Summary of Contents for H-KING Pacer G007
- Page 1 For Intermediate & Advanced Fliers. SAFETY PRECAUTIONS This radio control model is not a toy! Fist-time builders should seek advice from people having building Experience in order to assemble the model correctly and to produce Its performance to full extent. Assemble this kit only in places out of children’s reach! Take enough safety precautions prior to operating this model.
- Page 2 Find a pair of tail control wire as show. Before you install this control wire please clean it with alcohol. Install tail control wire as show. Two control wire after install. Trim off cover film and Install control horn and glue it with Epoxy or mid CA.
- Page 3 Made sure the contort horn was vertical when the tail surface was install. Drill some hole under the tail surface angle block to made the tail surface glue more secure. Drill some hole under the tail surface angle block to made the tail surface glue more secure.
- Page 4 Install the both tail surface at the tail and fix them with Epoxy. Before you install the tail surface you must install the “ Z” push rod with control horn first. Made sure the control surface was free before you glue the control horn.
- Page 5 Install the mini servo the servo bay as show in both side. Hook on receiver and tail control servo and turn on the radio then neutral both tail servo and fix the control wire as show. Place a 3-4cm long sticker Hook on tip end of servo tray for receiver mounting.
- Page 6 Mount the receiver at the end of the servo tray as Before you install the servo tray inside the Fuse. You need to hookup the tail control servo and three-6in servo extension wire for Ailerons and throttle control. Place double stick Velcro at font end of battery tray for battery mounting as show.
- Page 7 Place the ESC. understand the battery tray. Mount the battery on the battery tray in vertical and check the battery will not hit any servo arm. You can let the Antenna out from air exit. We don’t suggest you made the Antenna out from bottom because it is easy to cut the antenna when you landing.
- Page 8 Check the center point before you drill any hole for the motor install. You may need to use power tool to make big hole for spinner and motor ball bearing. After you drill four holes for motor mount bolt you may need use bigger drill bit to made the hole out side a bit bigger.
- Page 9 Use power tool to open the cooling air exit as show. Fix motor with four-countersink screw as show. Check the center when you mount the motor. the Alum. Spinner and carbon prop. That supply with deluxe kit. If you choice an ARF. Kit .please use a 40mm diameter spinner.
- Page 10 Please check tighten spinner lock screw before your hookup the power. the ultra cooling 70AMP. ESC. The motor plug was already installed if you choice the ESC. Supply with deluxe kit. You just need to install battery plug only. If you choice other motor and ESC. Please 4.5mm good quality plug that can be handle 100AMP.
- Page 11 Drill a 2mm hole at root of both sides of fuse. Join wing penal together with solid carbon wing join that supply with the kit. Mount both wings penal on to the Fus. With 3mm wing bolt. Trim of covering from Ailerons servo bay.
- Page 12 Use a thin wire to lead out the servo extend wire as show. Hack up servo lead and secure plug then put all wire in side wing panel. Install plastic servo tray to servo bay. Fix servo tray to the servo bay with CA. glue or epoxy.
- Page 13 Install control push rob as show. After you final adjust all control push rod, fix the servo hatch with TP screw as show. Check max low Ailerons and servo control horn as show. Notice: All control throw information you can find in SEP.
- Page 14 Check Ailerons center and servo control as show. Check Ailerons max up and servo control horn as show. Notice: All control throw information you can find in SEP. sheet. Adjust Ailerons max up throw with gage as show. Notice: All control throw information you can find in SEP.
- Page 15 Use CG. Checking tray to check and adjust correct CG. Use battery to adjust CG. Point is it necessarily. Find the carbon canopy parts. Install the lock wire inside the tube then glue it together with Epoxy.
-
Page 16: Specification
SPECIFICATION CODE:G007 ITEM: Description Description WING SPAN Suggest:ENGINES CLASS 2240mm WING AREA 36.85sq dm. Suggest:Motor/ESC X 40 L B.L,motor FUS. LENGTH RTF. WEIGHT GP.Setup 1052.5mm TOTAL LENGTH RTF. WEIGHT EP.Setup 1.7KG-2.0KG 1086mm CENTER OF GRAVITY 75MM at root RUDDER AREA WING INCIDENCE 1.5 °... - Page 17 Date: 15/01/2011 Description code size QUT′Y REMARK CARBON WING JOIN ￠10x268 WIRE ANTI ROLL PIN ￠2x25mm WING BOLT 2PCS ￠5x25 & Wing WING BOLT 2PCS ￠3X10 hardware pack Aileron push rod 2PCS ￠1.7x50 clevis 2PCS ￠2 e l i servo hactch mount screw 8PCS ￠2x10 Elevator...