Menu Survey - Danfoss EKD 316 Manual

Manual Superheat controller type EKD 316
Appendix I

Menu survey

Function
The menus from either column 1 or column 2 are shown
Normal display
During regulation the actual level of superheating is displayed.
(If you would like to see the expansion valve's actual opening degree, press the bottom button for
approx. one second.)
During control with an analogue signal the opening degree is displayed.
Reference
Units (0=°C+bar/1=°F+psig)
Correction of signal from S2
Correction of signal from S4
Start/stop of refrigeration
Alarm
Battery monitoring
Regulating parameters
Valve definition:
0 = ETS 12.5, ETS 25, KVS 15 5 = user-defined
1 = ETS 50, CCM 10, CCM 20, CCM 30 6 = Saginomiya UKV/SKV/VKV/PKV
2 = ETS 100, CCM 40 7 = ETS 6
3 = ETS 250, KVS 42 8 = CCMT 2, CCMT 4, CCMT 8
4 = ETS 400
On using external display EEKA 164A, please check page 9 section ETS valve
P: Amplification factor Kp
o56 = 1; n04 = 2.0
o56 = 2; n04 = 0.7
:
( Warning Changes to n04 are lost when changing o56)
I: Integration time T
D: Differentiation time Td (0 = off )
Max. value of superheat reference
Min. value of superheat reference
MOP (max = off )
Signal reliability during startup. Safety time period.
Should only be changed by trained staff
Signal reliability during startup – opening degree's start value. Should only be changed by trained
staff.
Stability factor for superheat control.
Changes should only be made by trained staff
Damping of amplification around reference value
Changes should only be made by trained staff
Amplification factor for superheat
Changes should only be made by trained staff
o56 = 1; n20 = 0.4
o56 = 2; n20 = 3.0
Warning :
( Changes to n20 are lost when changing o56)
Definition of superheat control mode
1 = MSS,
2 = LOADAP
Value of min. superheat reference for loads under 10%
Max. opening degree
Changes should only be made by trained staff
Number of steps from 0-100% opening degree (only if n03 = 5 (User-defined))
:
Note The display can only show three digits, but the setting value is four digits.
Only the three most important are shown, i.e. a reading of e.g. 250 means a setting of 2500. (Auto-
matic setting when valve is selected in n03).
Number of steps per second
Start backlash (extra closing steps at 0% opening (in % of n37))
Integration time for inner loop (TnT0)
Compensation for spindle play
16 DKRCC.PS.RP0.A1.02/520H7142
SW = 1.32
Fac. Application
Parameter Min. Max. set- choice
ting menu = o61
1 2
- K - 
- % -

r05 0 1 0 
r09 -10.0 K 10.0 K 0.0

r10 -10.0 K 10.0 K 0.0 
r12 Off/0 On/1 Off/0
 
A34 Off/0 On/1 Off/0  
n03 0 8 1  
n04 0.5 20 2.0/0.7

n05 30 s 600 s 120 
n06 0 s 90 s 0 
n09 2 K 15 K 10 
n10 1 K 12 K 6 
n11 0.0 bar 200 bar 20 
n15 0 sek. 90 sek 0 
n17 0% 100% 0

n18 0 10 5 
n19 0.0 1.0 0.3 
n20 0.0 10.0 0.4/3.0 
n21 1 2 1 
n22 1 K 15 K 4

n32 0 % 100 % 100 
10 990
n37 (100 (9990 262  
stp) stp)
300
n38 5 stp/s 300  
stp/s
n39 0% 100% 10  
n44 10 s 120 s 30 
n40 0 stp 100 stp 23 stp
©Danfoss A/S (AC-MCI / sw), 2014-03
Manual Superheat controller type EKD 316
Miscellaneous
Controller's address
If the valve's opening degree should be controlled with an external signal, the signal is defined as:
0: no signal
1: 0-20 mA
2: 4-20 mA
3: 0-10 V
4: 1-5 V
Manual control of outputs:
OFF: no manual control
1: Manual control with "o45" enabled
2: Simulate Alarm off : connection between 24 and 25
3: Simulate Alarm on : connection between 24 and 26
Working range for pressure transmitter – min. value
Working range for pressure transmitter – max. value
Refrigerant setting
1 = R12 6 = R13 11 = R114 16 = R401A 21 = R407A 26 = R600
2 = R22 7 = R13b1 12 = R142b 17 = R507 22 = R407B 27 = R600a
3 = R134a 8 = R23 13 = User def. 18 = R402A 23 = R410A 28 = R744
24 = R170 29 = R1270
4 = R502 9 = R500 14 = R32 19 = R404A
5 = R717 10 = R503 15 = R227 20 = R407C 25 = R290 30 = R417A
Manual control of the valve's opening degree. The function can only be operated if o18 has been set to
"1".
This function is only for manual operation. It must not be used for as a regulation function.
Selection of control mode:
1=Normal
2 = With inner loop (S media temperature less T0)
Application mode. Menus blanked out so only the shaded menus are seen. See the two columns to the
right.
1: Controlling a valve with an analogue signal
2: Superheat regulation
Service
Analog input (21-22)
Read status of input DI (20-21)
Temperature at S2 sensor
Superheat
Superheat reference
Read valve's opening degree
Read evaporating pressure
Read evaporating temperature
Temperature at S4 sensor
Configuration settings (n03, n37, n38, n39, n40, o03, o30, o56 and o61) available only when regulation is stopped (r12=off ).
Factory settings are indicated for standard unit (see code number, page 1). Other code number have customised settings.
Valve overview
n03 Valve type n37 n38
0 ETS 12½, ETS 25, KVS 15 262 300
1 ETS 50, CCM 10, CCM 20, CCM30 262 300
2 ETS 100, CCM 40 353 300
3 ETS 250, KVS 42 381 300
4 ETS 400 381 300
5 -
6 Saginomiya 24 30
7 ETS 6 24 30
8 CCMT 2, CCMT 4, CCMT 8 110 300
©Danfoss A/S (AC-MCI / sw), 2014-03 DKRCC.PS.RP0.A1.02/520H7142
o03 0 240 240

o10 0 4 0

o18 off/0 3 Off /0 
o20 -1 bar 0 bar -1.0
o21 1 bar 200 bar 12.0
31 = R422A R36 =
32 = R413A Opteon XP10
o30 0 37 0
33 = R422D 37 = R407F
34 = 427A
35 = R438A
o45 0 % 100 % 0

o56 1 2 1
o61 1 2 2 1
u06 mA (V)

u10 on/off 
u20 °C
u21 K
u22 K
u24 % 
u25 bar
u26 °C
u27 °C







2








17