TESY EVHP Series Manual page 17

7.1.3.2.2 ECO (economy) operating mode
To manually start the ECO operating mode, carry out the
following procedure:
•
Make sure that the keyboard is not locked
(paragraph 7.1.3.3),
procedure is in progress and that the equipment is
not in the Overboost operating mode;
•
Press the
flash;
•
Press the
ECONOMY operating mode.
To exit the procedure:
•
Press the key to exit this procedure without
changing the mode.
7.1.3.2.3 OVERBOOST operating mode
To manually start the OVERBOOST operating mode,
carry out the following procedure:
•
Make sure that the keyboard is not locked
(paragraph7.1.3.3) and that no other advanced
procedure is in progress;
• key for 1 second, either "ECO" or
Press the
"Auto" starts to flash;
•
Press the
on the display;
•
Press the key again to confirm and start the
OVERBOOST operating mode.
To exit the procedure:
•
Press the key to exit this procedure without
changing the mode.
7.1.3.3 Keyboard locking/unlocking
To lock the keyboard, carry out the following procedure:
•
Make sure that no other advanced procedure is
in progress;
•
Keep the and the
second: "Loc" will be shown on the display for 1
second.
If the keyboard is locked, it will not be possible to carry
out any kind of operation on the display interface.
By pressing any key, "Loc" will be shown for 1
second on the display.
To unlock the keyboard:
•
Keep the and the
second: "UnL" will be shown for 1 second on the
display.
7.1.3.4 Temperature setting in the ECO operating
mode (SP1)
•
Make sure that the keyboard is not locked
(paragraph 7.1.3.3) and that no other advanced
procedure is in progress;
•
Press and release the
shown on the display;
•
Press and release the
LED will flash;
•
Press either the
seconds; parameters r3, r4 and r5 can be seen;
•
Press and release the
out any other operations for 15 seconds: the
compressor LED
•
Press and release the
that no other advanced
key for 1 second, "ECO" starts to
key again to confirm and start the
or
keys until "ObSt" flashes
keys pressed for 1
keys pressed for 1
key: "SP1" will be
key: the compressor
or the key
key or do not carry
will switch off;
key.
To exit the procedure before its completion:
Do not carry out any operations for 15 seconds (any
changes will be saved).
7.1.3.5 Temperature setting in the Automatic mode
(SP2)
•
Make sure that the keyboard is not locked
(paragraph 7.1.3.3) and that no other advanced
procedure is in progress;
•
Press and release the
shown on the display;
•
Press either the
is shown on the display;
•
Press and release the
LED will flash;
•
Press either the
seconds; parameters r1, r2 and r5 can also be seen;
•
Press and release the
any other operations for 15 seconds: the compressor
LED (
•
Press and release the
To exit the procedure before its completion:
•
Do not carry out any operations for 15 seconds
(any changes will be saved).
7.1.3.6 Timeslot settings for the switching on/off of
the equipment
To start the procedure:
•
Make sure that the keyboard is not blocked and
that no other advanced procedure is in progress;
•
Press and release the
shown on the display.
To set the first timeslot:
•
Press and release either the
within 15 seconds to select "HOn1" (first switching on
time) and/or "HOf1" (first switching off time); select
"HOn2" and "HOF2" for the second switching on/off
time;
•
Press and release the
•
Press and release either the
and within 15 seconds;
•
Press and release the
any other operations for 15 seconds.
within 15
Page 17 of 28
or the key
key: the compressor
or the key
key or do not carry out
) will switch off;
key.
N.B.: before proceeding
timeslot settings, set day and real time
as described in paragraph 7.1.3.14
key;
key or do not carry out
key: "SP1" will be
until "SP2"
within 15
with the
key: "SP1" will be
or the key
or the key