Woodstock Shop Fox M1112 Owner's Manual page 45

Model M1112 (For Machines Mfd. Since 12/20)
Operation & Work Results
Symptom Possible Cause
Entire machine 1. Workpiece is unbalanced.
vibrates exces-
sively upon start- 2. Worn or broken gear present.
up and while run- 3. Chuck or faceplate has become unbalanced.
ning.
4. Spindle bearings at fault.
Cutting tool or 1. Tool holder not tight enough.
machine com- 2. Cutting tool sticks too far out of tool holder;
ponents vibrate lack of support.
excessively dur- 3. Gibs are out of adjustment.
ing cutting. 4. Dull cutting tool.
5. Incorrect spindle speed or feed rate.
Can't remove 1. Quill had not retracted all the way back into
tapered tool from the tailstock.
tailstock quill. 2. Debris was not removed from taper before
inserting into quill.
Cross slide, com- 1. Gibs are out of adjustment.
pound rest, or 2. Handwheel is loose.
carriage feed has 3. Lead screw mechanism worn or out of adjust-
sloppy operation. ment.
Cross slide, com- 1. Gibs are loaded up with shavings or grime.
pound rest, or
carriage feed 2. Gib screws are too tight.
handwheel is
hard to move. 3. Backlash setting too tight (cross slide only).
4. Bedways are dry.
Bad surface fin- 1. Wrong RPM or feed rate.
ish. 2. Dull tooling or poor tool selection.
3. Too much play in gibs.
4. Tool too high.
Inaccurate turn- 1. Headstock and tailstock are not properly
ing results from aligned with each other.
one end of the
workpiece to the
other.
Chuck jaws won't 1. Chips lodged in the jaws.
move or don't
move easily.
Carriage won't 1. Gears are not all engaged or broken.
feed, or hard to 2. Gibs are too tight.
move. 3. Loose screw on the feed handle.
4. Lead screw shear pin has sheared.
Tailstock quill 1. Quill lock lever is tightened down.
will not feed out
of tailstock.
Corrective Action
1. Reinstall workpiece so it is as centered with the
spindle bore as possible.
2. Inspect gears and replace if necessary.
3. Rebalance chuck or faceplate; contact a local
machine shop for help.
4. Tighten or replace spindle bearings.
1. Check for debris, clean, and retighten.
2. Reinstall cutting tool so no more than
total length is sticking out of tool holder.
3. Tighten gib screws at affected component.
4. Replace or re sharpen cutting tool.
5. Use the recommended spindle speed.
1. Turn the quill handwheel until it forces taper out of
quill.
2. Always make sure that taper surfaces are clean.
1. Tighten gib screw(s).
2. Tighten handwheel fasteners.
3. Tighten any loose fasteners on lead screw mecha-
nism.
1. Remove gibs, clean ways/dovetails, lubricate, and
readjust gibs.
2. Loosen gib
bedways.
3. Slightly loosen backlash setting by loosening the
locking screw and adjusting the spanner ring at the
end of the handle.
4. Lubricate bedways and handles.
1. Adjust for appropriate RPM and feed rate.
2. Sharpen tooling or select a better tool for the
intended operation.
3. Tighten gibs.
4. Lower the tool position.
1. Realign the tailstock to the headstock spindle bore
center line.
1. Remove jaws, clean and lubricate chuck threads,
and replace jaws.
1. Adjust gear positions or replace.
2. Loosen gib screw(s) slightly.
3. Tighten.
4. Correct for cause of shear pin breakage, and replace
shear pin.
1. Turn lever counterclockwise.
-43-
⁄
1
3
screw(s) slightly, and lubricate
of the