Installing Hook; Operation; Maintenance - Makita DFL020F Instruction Manual

For tool with shallow driver bit hole
A = 1 2mm
B= 9 mm
For tool with deep driver bit hole
A = 1 7mm
B= 1 4 mm
A = 1 2mm
B= 9 mm
Fig.12: 1. D ri v er bit 2. S lee v e
T o install t h e d ri v er bit, pull t h e slee v e in t h e d ire c tion o f
t h e arro w an d insert t h e d ri v er bit into t h e slee v e as f ar
as it w ill go.
T h en release t h e slee v e to se c ure t h e d ri v er bit.
T o remo v e t h e d ri v er bit, pull t h e slee v e in t h e d ire c tion
o f t h e arro w an d pull t h e d ri v er bit out.
NOTE: I f t h e d ri v er bit is not inserte d d eep enoug h
into t h e slee v e, t h e slee v e w ill not return to its original
position an d t h e d ri v er bit w ill not be se c ure d . I n t h is
c ase, tr y re-inserting t h e bit a c c or d ing to t h e instru c -
tions abo v e.
NOTE: When it is difficult to insert the driver bit, pull
t h e slee v e an d insert it into t h e slee v e as f ar as it w ill
go.
NOTE: A f ter inserting t h e d ri v er bit, make sure t h at it
is firmly secured. If it comes out, do not use it.

Installing hook

Optional accessory
T h e h ook is use f ul to h ang t h e tool. I nstall t h e h ook to
t h e h oles on t h e tool bo d y .
Fig.13: 1. H ook 2. H ole

OPERATION

Hold the tool firmly and place the socket over the bolt
or nut. T h en s w it c h t h e tool on. W h en t h e c lut c h c uts
in, t h e motor w ill stop automati c all y . T h en release t h e
s w it c h trigger.
NOTE: H ol d t h e tool w it h its s q uare d ri v e pointe d
straig h t at t h e bolt or nut, or t h e bolt or nut w ill be
d amage d .
Limits of fastening capacity
U se t h e tool w it h in t h e limits o f f astening c apa c it y . I f y ou
use t h e tool be y on d t h e limits, t h e c lut c h d oes not w ork.
A n d t h e tool c annot d eli v er enoug h f astening tor q ue.
U se only th ese ty pe of d riv er
bit. F ollow th e proc ed ure
1 . ( Note) Bit-piec e is not
nec essary .
T o install th ese ty pes of d riv er
bits, f ollow th e proc ed ure 1 .
T o install th ese ty pes of d riv er
bits, f ollow th e proc ed ure 2.
( Note) Bit-piec e is nec essary
f or installing th e bit.
For model DFL020F
360°
300°
240°
2
180°
120°
60°
30°
0.5
1. R ange o f f astening c apa c it y 2. R otation angle
3. T or q ue
For model DFL063F
360°
300°
240°
2
180°
120°
60°
30°
1.5
1. R ange o f f astening c apa c it y 2. R otation angle
3. T or q ue
NOTE: T h e rotation angle is t h e angle f rom t h e point
t h at t h e bolt is tig h tene d in 5 0 %
t h e point t h at t h e bolt is tig h tene d in 1 00 %
NOTE: U se o f a c ol d batter y c artri d ge ma y gi v e
w arning f or batter y c apa c it y b y L E D in d i c ator an d
beeper an d stop t h e tool imme d iatel y , e v en i f it is f ull y
c h arge d . I n t h is c ase, t h e f astening c apa c it y ma y be
inferior to the specification on this manual.

MAINTENANCE

CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
T o maintain pro d u c t S A F E T Y an d R E L I A B I L I T Y ,
repairs, an y ot h er maintenan c e or a d j ustment s h oul d
be per f orme d b y Makita A ut h ori z e d or F a c tor y S er v i c e
C enters, al w a y s using Makita repla c ement parts.
9 ENGLISH
1
1.0 1.5
3
N•m
1
4.0
3
N•m
o f d esire d tor q ue to
tor q ue.
2.0
6.5