Makita DFL020F Instruction Manual page 8

Function
Motor f ailure d etec tion
D ouble-h itting d etec tion
Maintenanc e alarm
A larm f or unav ailable
d ata c ommunic ation
( w ith th e tool in c onnec -
tion w ith P C )
I nd ic ation th at d ata c om-
munic ation is av ailable
( w ith th e tool in c onnec -
tion w ith P C )
Adjusting the fastening torque
W h en y ou w is h to d ri v e ma c h ine s c re w s, h e x bolts,
et c . w it h t h e pre d etermine d tor q ue, a d j ust t h e f astening
tor q ue as f ollo w s.
1. I nstall t h e batter y c artri d ge.
2. O pen t h e c h ange plate b y h an d so t h at y ou c an
see a h ole.
Fig.7: 1. C h ange plate
3. P ull t h e s w it c h trigger an d release it so t h at t h e
a d j ust ring rotates an d t h e h ole be c omes v isible. A n d
t h en remo v e t h e batter y c artri d ge.
4. U se an optional a d j ust grip to a d j ust t h e f astening
tor q ue. I nsert t h e pin o f t h e a d j ust grip into t h e h ole
in t h e f ront o f t h e tool. A n d t h en, turn t h e a d j ust grip
c lo c k w ise to set a greater f astening tor q ue, an d c oun-
ter c lo c k w ise to set a smaller f astening tor q ue. U se t h e
y ello w line as a roug h gui d e.
Fig.8: 1. A d j ust grip 2. H ole f or a d j ust grip 3. Y ello w
line
5. I nsert t h e batter y c artri d ge an d be sure t h at a
f astening tor q ue h as been set up b y using a f astening
tor q ue tester.
6.
C lose t h e c h ange plate b y h an d se c urel y .
Adjusting no-load speed and
revolution angle etc.
Y ou c an a d j ust t h e no-loa d spee d , number o f turn, et c .
o f t h e tool w it h y our c omputer. I nstall t h e appli c ation
so f t w are in y our c omputer an d c onne c t it to t h e tool w it h
an U S B c able.
Fig. 9 : 1. U S B c able 2. U S B c o v er 3. U S B port
NOTICE:
Make sure t h at t h e U S B c o v er c lose d
w h en f astening.
NOTE: F or t h e appli c ation so f t w are, please c onta c t
Makita sales representati v e.
Status of the tool
Motor f ailure h as been F lic kers in red and green
d etec ted . A t th is time, alternativ ely .
tool d oes not w ork.
W h en th e operator L igh ts up in red .
starts to re-f asten an
alread y -f astened sc rew ,
th e tool d etec t it and
stops.
A maintenanc e time h as F lic kers in y ellow .
c ome ac c ord ing to y our
preset number of sc rew s
d riv en.
D ata c annot be F lic kers in y ellow .
ex c h anged betw een th e
tool and P C in spite of
th e c onnec tion.
T h e tool is c onnec ted to F lic kers in green.
P C and d ata c ommuni-
c ation is av ailable.
Status of the LED indicator/beeper
LED indicator
A series of sh ort beeps
A long beep
ASSEMBLY
CAUTION:
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Selecting correct socket
T h ere are d i f f erent t y pes o f so c kets f or some mo d els
d epen d ing on appli c ations. C h oose an d install a c orre c t
so c ket f or y our appli c ation.
Installing or removing socket
Fig.10: 1. S o c ket 2. H ole 3. P in
T o install t h e so c ket, pus h it onto t h e s q uare d ri v e o f t h e
tool w it h one h an d b y d epressing a pin on t h e s q uare
d ri v e w it h anot h er h an d until it lo c ks into pla c e. T o
remo v e t h e so c ket, simpl y pull it o f f d epressing t h e pin
on t h e s q uare d ri v e.
CAUTION:
the socket is properly locked onto the square
drive. I n c omplete atta c h ment o f t h e so c ket ma y
c ause in j ur y .
Installing or removing driver bit/
socket bit
Country specific
Fig.11
U se onl y d ri v er bit / so c ket bit t h at h as inserting portion
shown in the figure. Do not use any other driver bit/
so c ket bit.
8 ENGLISH
Action to be taken
Beeper
A sk y our loc al Makita
S erv ic e C enter f or repair.
– R eset th e alarm w ith th e
applic ation sof tw are.
– R estart th e applic ation
sof tw are and re-c onnec t
th e U S B c able.
–
Always be sure that the tool is
Before operation, make sure that
–
–