Campingaz RBS ESTATE 4 Series Operation And Maintenance page 11

that the ventilation openings in the gas receptacle
housing are not obstructed, if appropriate.
that the grease trap(s) is (are) correctly inserted into its
(their) compartment and that it (they) is (are) correctly
positioned, as far as it (they) will go.
that the heat reflector is correctly installed in the
bottom of the bowl.
that the bowl's 6 removable parts are reinserted (see §
p cleaning).
h) LIGHTING THE BARBECUE BURNERS
Your barbecue is equipped with a STOPGAZ system.
This safety system automatically shuts off the gas flow
to the burner when the burner flame is blown out (wind
etc.).
Open the lid.
Make sure that the control knobs are in the "OFF"
position (O).
Open the gas cylinder valve.
Press, then turn the knob corresponding to the burner
in a counter clockwise direction to the (
Press the ignition button (
Keep the button depressed for a maximum of 10
seconds. If the burner does not light after 10 seconds,
reset the control button to the OFF (O) position. Wait
for a minute before starting the ignition procedure once
more.
When the burner is lit, keep the control button
depressed for 10 seconds and then release it. This
enables the STOPGAZ safety system to activate.
Adjust the flame to the desired height by turning the
knob to ( ) or ( ).
Do the same for all the burners.
If the electronic ignition system does not work, light the
barbecue manually (next paragraph).
Lighting the burner manually
If the electronic ignition system fails to work, use a
match to light the burner.
Open the lid.
Make sure that the control knobs are in the "OFF"
position (O).
Remove one of the cooking grids to gain access to the
burners.
) position.
).
Turn on the gas supply (valve or lever on the
regulator).
Put a lighted match in front of the burner.
Press, then rotate the knob corresponding to the
burner in a counter clockwise direction to the (
position.
When the burner is lit, keep the control button
depressed for 10 seconds and then release it.
Adjust the flame to the dimensions of the recipient by
using the two flow positions: HIGH (
Once the burner is lit, replace the grid or hotplate.
i) EXTINGUISHING THE BARBECUE
Set the control knobs to the "off" position (O), then close
the cylinder valve.
j) LIGHTING THE HOT PLATE
model)
The hot plate can be used alone or at the same time as
the grill.
Lighting:
Open the gas cylinder valve.
Check gas circuit sealing from the frame to the hot
plate (see § f).
Open the hotplate lid and retract it to the back of the
hotplate, sliding it in the grooves at the side.
Press and rotate the control lever on the stove (
to its FULL FLOW position (
Press the ignition button ( ) until the burner lights. If
the burner does not light after 10 seconds, put a match
to the edge of the burner.
Adjust the flame to the dimensions of the recipient by
using the two flow positions: HIGH (
Do not use recipients with a diameter less than 10 cm
or over 24 cm.
k) TURNING OFF THE HOT PLATE
(depending on the model)
Return the control lever (
then close the valve on the gas bottle if the grill is not in
use.
To close the lid, slide it in its grooves, pulling it upwards
until it reaches the spindle, then tip it forwards.
l) LIGHTING OF THE CONSOLE
the model)
The lighting system of the console is powered by 4 type
AA (LR06) batteries provided with the barbecue grill.
The battery box is located on the front right hand leg,
behind the right door. Remove the cover of the battery
holder box by sliding it upwards. Insert the batteries
while respecting the polarities indicated and then replace
the cover.
To turn the lighting on or off, press on the
stop start button located to the left of the
console and identified by this pictogram.
11
)
) or LOW ( ).
(depending on
)
).
) or LOW ( ).
) to the OFF (O) position,
(depending on
GB