KEB COMBIVERT F4-S Instruction Manual
KEB COMBIVERT F4-S Instruction Manual

KEB COMBIVERT F4-S Instruction Manual

Control circuit
Hide thumbs Also See for COMBIVERT F4-S:

Advertisement

KEB COMBIVERT F4-S Instruction Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the COMBIVERT F4-S and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for KEB COMBIVERT F4-S

  • Page 1 (217) 352-9330 | Click HERE Find the KEB / Combivert 00.F4.010-5A08 125k at our website:...
  • Page 2 C O M B I V E R T BETRIEBSANLEITUNG Steuerteil INSTRUCTION MANUAL Control circuit MANUEL D'INSTRUCTION Carte de commande MANUALE DI ISTRUZIONE Circuito di controllo MANUAL DE INSTRUCCIONES Circuito de control РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ Карта управления Erst Betriebsanleitung Teil lesen! Read Instruction manual part before!
  • Page 3 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 4 Steuerteil Seite 4 ....23 Control circuit Page 24 ....43 Carte de commande Page 44 ....63 Circuito di controllo Page 64 ....83 Circuito de control Page 84 ....103 Страница 104 ... 123 Карта управления Passwords Page 129 Artisan Technology Group - Quality Instrumentation ...
  • Page 5 Help Used to mark additional important informations. Information The KEB COMBIVERT is operated with voltages that can cause a Attention severe electric shock dangerous to life. Therefore the installation of the unit as well as of the available accessories is only permissible by Only qualified qualified electro-personnel.
  • Page 6: Table Of Contents

    Table of Contents Table of Contents Installation and Connection......26 1.1. Control circuit Version C........26 1.1.1 Assignment of Terminal Strip X1 ......26 1.1.2 Connection of the Control ........27 1.1.3 Digital Inputs............27 1.1.4 Analog Inputs ............27 1.1.5 Outputs ..............
  • Page 7: Installation And Connection

    1. Installation and Connection 1.1. Control circuit 22 23 1 2 3 4 Version C 1.1.1 Assignment of 6 7 8 9 10 11 12 13 14 15 16 17 18 Terminal Strip X1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Function Name Description X1.1...
  • Page 8: Connection Of The Control

    Installation and Connection 1.1.2 Connection of the In order to prevent a malfunction caused by interference voltage supply Control on the control inputs, the following directions should be observed: - Use shielded/drilled cables - Lay shield on one side of the inverter onto earth potential - Lay control and power cable separately (about 10...20 cm apart) - Lay crossings in a right angle (in case it cannot be prevented) Use of internal voltage supply...
  • Page 9: Control Circuit Version S

    Installation and Connection 1.2 Control circuit Version S 1 2 3 4 5 6 7 8 9 10 11 12 13 14 1.2.1 Assignment of Terminal Strip X1 Function Name Description X1.1 NO contact Relay output X1.2 Opening contact Function see parameter CP.22 X1.3 Switching contact ( factory setting: fault indication)
  • Page 10: Outputs

    Voltage supply-Plus +5V (I = 10 mA)) C/C' DGND Data reference potential TxD-A Transmitter signal A/RS485 TxD-B Transmitter signal B/RS485 Informations about other versions of operators contact KEB! Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 11: Keyboard

    Operation of the Unit When switching on KEB COMBIVERT the value of parameter CP.1 2.1.2 Keyboard appears. (See Drive mode to switch the keyboard function) The function key (FUNC) FUNC. changes between the parameter value and SPEED parameter number. With UP and DOWN the...
  • Page 12: Parameter Summary

    Operation of the Unit 2.2 Parameter Summary Display Parameter Adjust. range Resolution Factory setting CP. 0 Password input 0...9999 CP. 1 Actual frequency display - 0,1 Hz CP. 2 Inverter status display CP. 3 Actual load CP. 4 Peak load CP.
  • Page 13: Operating Display

    Operation of the Unit 2.4 Operating Display The 4 parameters below serve to control the frequency inverter during operation. Actual frequency display Display of the actual output frequency with a resolution of 0.0125 Hz. The rotation of the inverter is indicated by the sign. Output frequency 18.3 Hz, rotation forward Examples: Output frequency 18.3 Hz, rotation reverse...
  • Page 14: Basic Adjustment Of The Drive

    Operation of the Unit 2.5 Basic Adjustment The following parameters determine the fundamental operating data of of the Drive the drive. They should be checked and/or adapted to the application. With the adjusted frequency here the inverter reaches a maximal output Rated frequency voltage.
  • Page 15 Operation of the Unit Decceleration time The parameter determines the time needed in order to decelerate from 100 to 0 Hz. The actual deceleration time is proportional to the frequency change. delta f x CP. 8 = actual deceleration time 100 Hz Adjustment range: 0.01...300 s...
  • Page 16: Special Adjustments

    Operation of the Unit 2.6 Special The following parameters serve to optimize the drive and adaption onto Adjustments certain applications. These adjustments can be ignored at the initial startup. This function protects the frequency inverter against switching off by Max. ramp current overcurrent during the acceleration ramp.
  • Page 17 Operation of the Unit Speed search When connecting the frequency inverter onto a decelerating motor, an error can be triggered by the differing rotating field frequencies. At activated on speed search the inverter searches the actual motor speed, adapts its output frequency and accelerates with the adjusted ramp onto the given set value.
  • Page 18 Operation of the Unit Slip compensation Slip compensation balances the speed changes caused by the load variation. In order to activate the function, set the value at 1.00 and optimize as directed in the examples below. Adjustment range: -2.50...2.50 Resolution: 0.01 Factory setting: 0.00 (=off)
  • Page 19 DC-braking With DC-braking the motor is not decelerated by the ramp. Quick braking is caused by D.C. voltage, which is applied onto the motor winding. This parameter determines how the dc-braking is triggered. Value Activation DC-braking deactivated DC-braking at switch off of the direction of rotation and in reaching 0Hz.
  • Page 20 Relay output Relay output (terminal X1.1...X1.3) is adjusted in the factory as a fault relay. This parameter can adjust the function of the output onto any function listed in the table below. Value Function No function Generally on Fault relay Fault relay (not at under voltage error) Overload alert signal (10s before switch off) Overtemperature alert signal inverter...
  • Page 21 Operation of the Unit The set value input REF (terminal X1.17 / version C) can be driven by Reference signal various signal levels. It operates cummulatively to the difference voltage input (terminal X1.8 and X1.9 / version C), but can also serve as the sole input to the set value presetting.
  • Page 22: The Drive Mode

    Drive mode 2.7 The Drive Mode The drive mode is a operating mode of KEB COMBIVERT to start the drive manually by the operator. After switching the control release the set value and rotation presetting is done exclusively by the keyboard. In order to activate the drive mode the corresponding password in CP.0 must be...
  • Page 23: Error Diagnosis

    3. Error Diagnosis Error messages are represented with an "E. " and the corresponding error in the display of the KEB COMBIVERT. The displays and their causes are described below. Occurs, when the intermediate ciruict voltage falls below the permissible value.
  • Page 24 Quick referenz Display Parameter Adjust. range Resolution Customer setting CP. 0 Password input 0...9999 CP. 1 Actual frequency display - 0,1 Hz CP. 2 Inverter status display CP. 3 Actual load CP. 4 Peak load CP. 5 Rated frequency 0...409.58 Hz 0.0125 Hz ____________ CP.
  • Page 25 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 26: Passwords

    Password ENTER Password a) CP-Parameter "read only" FUNC ENTER Password b) CP-Parameter "read/write" FUNC ENTER Password c) Drive mode activ FUNC Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 27 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
  • Page 28 Angebote enthalten nur Richtwerte. Technische Änderungen jeder Art behalten wir uns vor. Alle Rechte vorbehalten. Nachdruck, Vervielfältigung und fotomechanische Wiedergabe sind ohne schriftliche Genehmigung durch KEB auch auszugsweise verboten. Avant la livraison tous les produits passent par différents contrôles fonctionnels et qualitatifs de manière à...
  • Page 29 Karl E. Brinkmann GmbH Försterweg 36-38 • D-32683 Barntrup fon: +49 5263 401-0 • fax: +49 5263 401-116 net: www.keb.de • mail: info@keb.de KEB Antriebstechnik GmbH & Co. KG KEB - YAMAKYU Ltd. Wildbacher Str. 5 • D–08289 Schneeberg 15–16, 2–Chome, Takanawa Minato-ku J–Tokyo 108-0074...

This manual is also suitable for:

Combivert f4-c

Table of Contents