Related Manuals for Munters Aerotech VX Series
Summary of Contents for Munters Aerotech VX Series
- Page 1 Aerotech VX Fan Direct Drive Instruction Manual 14” - 26” Fans VX26 VX14 - VX24 VX Fans Direct Drive Models: VX14F1 • VX16F1 • VX18F1 • VX24F1 • VX24F3 • VX26F1 • VX26F3 © Munters Corporation, July 2020 QM1105r3...
- Page 2 With the proper installation and maintenance it will provide many years of service. Please Note: To achieve maximum performance and insure long life from your Munters product it is essential that it be installed and maintained properly. Please read all instructions carefully before beginning installation. Warranty: For Warranty claims information see the “Warranty Claims and Return Policy”...
- Page 3 Fan Dimensions 2. Installation Instructions Install PT Style Shutter PZ Style Shutter 3. Electrical Wiring 4. Operation 5. Maintenance 6. Winterizing Winterizing Winter Weather Protection 7. Troubleshooting 8. Exploded View and Parts List 16-17 © Munters Corporation, July 2020 QM1105r3...
-
Page 4: Unpacking The Equipment
1.1 Parts List Each Fan includes: 1 – Direct Drive Fan 1 – Hardware Package as follows: HP1145 – VX Direct Drive Fans Qty. Cat. No. Description KS2105 #14 x 1.5” Lag Screw, SS © Munters Corporation, January 2020 QM1105r3... -
Page 5: Side View
20” ⁄ ” ⁄ ” ⁄ ” ⁄ ” ⁄ ” 28 ⁄ ”W 28 ⁄ ”H 26” ⁄ ” 22” 33” ⁄ ” ⁄ ” ⁄ ” 27” ⁄ ”W 30 ⁄ ”H © Munters Corporation, July 2020 QM1105r3... -
Page 6: Installation Instructions
Lag Screw [A} VX Fan Note: Outlet of fan comes unguarded, it is recommended that a Munters Discharge Cone with Guard, a Fan Hood with Guard or a guard by others is installed on outlet of fan at this time. OUTSIDE... - Page 7 Fasten shutter in place by rotating the side and top shutter clips over the shutter flanges. See Figure 3B. Installation is now complete, proceed to electrical wiring section. PZ/PV Shutter Figure 3A Figure 3B © Munters Corporation, July 2020 QM1105r3...
- Page 8 Fasten shutter in place by rotating the side and top shutter clips over the shutter flanges. See Figure 5B. Installation is now complete, proceed to electrical wiring section. PT Shutter Figure 5B Figure 5A © Munters Corporation, January 2020 QM1105r3...
-
Page 9: Electrical Wiring
For electrical connection requirements, refer to diagram on motor nameplate and to information enclosed with the Munters environmental control to be used. After wiring check for proper motor rotation. - Page 10 The use of a quality frequency drive and the installation of line reactors is recommended to reduce voltage spikes and harmonic distortion. Minimum operating frequency of 30 Hz. Will require three pole contractors with overload protection (by others). © Munters Corporation, January 2020 QM1105r3...
-
Page 11: Operation
1500 1020 1110 1090 1200 1750 1100 1220 1180 1350 2000 1190 1330 1260 1460 2500 1380 1600 1430 1630 3000 1600 — — 1640 — — 3170 1680 — — 1720 — — © Munters Corporation, July 2020 QM1105r3... - Page 12 — — 1750 2000 2250 2500 2750 3000 3500 4000 4500 5000 5500 6000 6500 1030 7000 1040 — — 7500 — — 1020 — — 8000 1050 — — — — — — © Munters Corporation, January 2020 QM1105r3...
-
Page 13: Maintenance
Electrical Devices. connections. Wiring should be secure and in good condition. Remove any dust build-up from control case and sensor using a soft brush or cloth. NEVER CLEAN ELECTRICAL EQUIPMENT WITH A PRESSURE WASHER! © Munters Corporation, July 2020 QM1105r3... - Page 14 Munters Product and System manufacturers recommendations. The supplier listing above is given Warranties do not cover cone or fan as a reference only. Munters does not endorse any specific snow guard product and no performance warranty is implied. damage from external sources.
-
Page 15: Troubleshooting
2. Propeller damaged 3. Repair or replace motor 3. Motor shaft bent 1. Override thermostat set incorrectly 1. Set to the correct temperature 2. Control set for continuous operation 2. Set speed control correctly © Munters Corporation, July 2020 QM1105r3... -
Page 16: Exploded View
Exploded View © Munters Corporation, January 2020 QM1105r3... - Page 17 Shutter for 14” Fan, 16³⁄₄”SQ., White Plastic PZ1618 Shutter for 16”/18” Fan, 21⁵⁄₈” SQ., White Plastic PZ24 Shutter for 24” Fan, 27⁵⁄₈” SQ., White Plastic PV26 Shutter for 26” Fan, 29.4” SQ., White Plastic © Munters Corporation, July 2020 QM1105r3...
- Page 18 VX Fan 14”, 16”, 18”, 24”, 26” with ”RC” Cone is developed and produced by Munters Corporation, Lansing, Michigan U.S.A. 1-800-227-2376 Munters Europe AB, Isafjordsgatan 1, P.O. Box 1150, SE-164 26 Kista, Sweden. Phone +46 08 626 63 00, Fax +46 8 754 56 66.
Need help?
Do you have a question about the Aerotech VX Series and is the answer not in the manual?
Questions and answers