mycom i125S Instruction Manual page 62

No.
6 Gasket, Strainer Cover
7-1 O-ring see Note 1
7-2 O-ring see Note 1
12 Gasket, Bearing Head
17 Gasket, Bearing Cover
23 Gasket, End Cover
27-1 Radial Bearing M
27-2 Radial Bearing F
30 Balance Piston see Note 2
33 Sleeve, Balance Piston see Note 2
35 O-ring see Note 1
38-1 Thrust Bearing M
38-2 Thrust Bearing F
40-1 Lock Washer
40-2 Lock Washer
49 O-ring see Note 1
50 Oil Seal see Note 2
52 Gasket, Seal Cover
93 Gasket, Suction Flange
96 Gasket, Discharge Flange
100 Mechanical Seal Assembly see Note 3
150-1 O-ring see Note 1
150-2 O-ring see Note 1
216-2 Flange Gasket, Oil Inlet Port
237-1 Torsional Slip Washer M
237-2 Torsional Slip Washer F
395 Gasket, Unloader Cover
480 Strainer Element see Note 2
489 Valve Seat
491 Check Valve Shaft see Note 2
495 O-ring see Note 1
Note 1: The part code of the O-ring is the one assigned to NBR-70-1 which is standard material.
Note 2: When checking each part (No.30, 33, 50, 480, 491) and in case of malfunction's being a little
seen, that it is possible to replace, prepare beforehand. If a special malfunction is not seen, it is
possible to use in the continuation.
Note 3: Mechanical seal assembly (No.100) should be replaced if any defect is found during inspection.
Actually, however, it is sometimes difficult to find out defects on the sliding surface only through visual
inspection. In such circumstances, MAYEKAWA recommends to replace it with a new one.
Also, if it is difficult to stop the compressor operation except for scheduled inspections, MAYEKAWA
recommends replacing No.100 in the same way.
Screw Compressor i-series
Table 5-8 List of replacement parts of i160
Part name
Chapter 5 Maintenance and Inspection
Code No.
CS00900-I160 i160 t=0.5
PA12-150 JIS B 2401 G150
PA12-140 JIS B 2401 G140
CS01200-I160 i160 t=0.5
CS01700-I160 i160 t=0.5
CS02300-I160N i160 t=1.0
CS02800-FM160M FM160
CS02800-FM160F FM160
CS03000-I160 i160
CS03300-I160 i160
PA11-024 JIS B2401 P24
CS03800-I160M 7311B
CS03800-I160F 7312B
NG32-011 AW11
NG32-012 AW12
PA12-090 JIS B 2401 G90
CS05000-160VD 160*** (S55×70×9)
CS05200-160N 160*** t=0.5
PL300-125 ANSI 300 # 5"
PL300-080 ANSI 300 # 3"
CS10002-160EBS 160V BBSE
PA12-110 JIS B 2401 G110
PA12-115 JIS B 2401 G115
CR72000-025N MYCOM 25A
CS23700-FM160M FM160
CS23700-160 160***
CS39500-I160 i160 t=1.0
i160 #150 Φ160×200
CS48000-I160
CS48900-I160 i160
CS49100-I160 i160
PA11-007 JIS B 2401 P7
5.4 Compressor Disassembly Preparation
5-9
2200M4JE-HO-iS2-N_2014.04.
Remarks Qty
2
1
1
1
1
1
2
2
1
1
2
1
1
1
1
1
1
1
1
1
1set
1
1
1
1
1
2
1
1
1
1