Related Manuals for Mellanox Technologies MIS5022Q-1BFR
Summary of Contents for Mellanox Technologies MIS5022Q-1BFR
- Page 1 Dismantling Guide OPNs MIS5022Q-1BFR, MIS5022Q-1BRR Rev. 1.0 Document no. 3408 Mellanox Technologies Confidential http://www.mellanox.com...
- Page 2 Mellanox®, BridgeX®, ConnectX®, InfiniBlast®, InfiniBridge®, InfiniHost®, InfiniRISC®, InfiniScale®, InfiniPCI®, PhyX® and Virtual Protocol Interconnect® are registered trademarks of Mellanox Technologies, Ltd. CORE-Direct and FabricIT are trademarks of Mellanox Technologies, Ltd. All other marks and names mentioned herein may be trademarks of their respective companies.
-
Page 3: Table Of Contents
Figure 5 Fan Location ......................10 Figure 6 Fan Harness Locations ....................10 Figure 7 Remove Fan Module ....................11 Figure 8 Board Screw Locations ..................... 12 Figure 9 Remove Heat Sink ....................13 Mellanox Technologies Confidential 3 of 13... -
Page 4: Revision
Audience This manual is intended for technicians who dismantle the switch systems as a reference for WEEE recyclers. Mellanox Technologies emphasizes the importance of carefully following all procedures described in this guide to prevent personal injury. Switch OPNs This document is valid for all of the switch OPNs listed in Table 2. -
Page 5: Policy Statement
Mellanox Technologies is committed, therefore, to meeting the requirements of the European Union’s WEEE (waste electrical and electronic equipment) directive. -
Page 6: Dismantling Instructions
To disassemble the InfiniBand switch system you will need a small Philips screwdriver. The pictures displayed in the following pages provide visual guidance explaining how to remove the modules from the mechanical base. Mellanox Technologies Confidential 6 of 13... -
Page 7: Cover
Dismantling Guide Rev. 1.0 Cover 1. Unscrew the rear-side screws, and slide the cover to the back for opening it. 2. Slide the top to the rear and lift off. Figure 1 Remove the Cover Mellanox Technologies Confidential 7 of 13... -
Page 8: Extracting The Power Supply Unit
1. Disconnect the 3 harness connectors from the main board, the inlet and the ground. Figure 3 Harness Location for PSU 2. Disassemble the 4 screws & washers attaching the power supply to the mechanical base. Mellanox Technologies Confidential 8 of 13... -
Page 9: Figure 4 Remove The Power Supply Unit From The Switch
Dismantling Guide Rev. 1.0 Figure 4 Remove the Power Supply Unit from the Switch Mellanox Technologies Confidential 9 of 13... -
Page 10: Extracting The Fan Unit
Extracting the Fan Unit The Fan unit is located in the rear of the system. Figure 5 Fan Location 1. Disconnect the 3 harnesses from the fan unit to the board. Figure 6 Fan Harness Locations Mellanox Technologies Confidential 10 of 13... -
Page 11: Figure 7 Remove Fan Module
2. Disassemble the 2 screws attaching the Fan wall to the bottom of the mechanical enclosure base. 3. Disassemble the 4 screws attaching the Fan wall to the rear of the mechanical base. Figure 7 Remove Fan Module 4. Remove the fan unit. Mellanox Technologies Confidential 11 of 13... -
Page 12: Extracting The Board
Dismantling Guide Rev. 1.0 Extracting the Board 1. Disassemble the 5 screws and washers attaching the main board to the mechanical base. Figure 8 Board Screw Locations 2. Remove the Main board. Mellanox Technologies Confidential 12 of 13... -
Page 13: Figure 9 Remove Heat Sink
Dismantling Guide Rev. 1.0 3. Unscrew the Heat-sink screws to remove the Heat-sink. Figure 9 Remove Heat Sink Mellanox Technologies Confidential 13 of 13...